Stability of hydrogenated nanodiamonds under extreme ultraviolet irradiation

It is generally accepted that diamond is resistant to a wide spectrum of electromagnetic radiation from the ultraviolet through to the soft X-ray range, which makes it very attractive for the fabrication of diamond-based photodetectors. However the effect of photon radiation on the diamond structure has not yet been examined. In the work presented here, photoelectron spectroscopy has been used to study the graphitization of nanodiamond crystallites exposed to extreme ultraviolet radiation. Under such irradiation, the surface hydrogen groups and graphite species are found to prevent graphitization. The mechanism of radiation-induced nanodiamond graphitization is discussed.     

Threshold and growth mechanism of fatigue cracks under mode II and III loadings

ABSTRACT The fatigue crack growth behaviour of 0.47% carbon steel was studied under mode II and III loadings. Mode II fatigue crack growth tests were carried out using specially designed double cantilever (DC) type specimens in order to measure the mode II threshold stress intensity factor range, ΔK_IIth. The relationship ΔK_IIth > ΔK_Ith caused crack branching from mode II to I after a crack reached the mode II threshold. Torsion fatigue tests on circumferentially cracked specimens were carried out to study the mechanisms of both mode III crack growth and of the formation of the factory‐roof crack surface morphology. A change in microstructure occurred at a crack tip during crack growth in both mode II and mode III shear cracks. It is presumed that the crack growth mechanisms in mode II and in mode III are essentially the same. Detailed fractographic investigation showed that factory‐roofs were formed by crack branching into mode I. Crack branching started from small semi‐elliptical cracks nucleated by shear at the tip of the original circumferential crack.     

Effective lightning protection schemes for distribution line

The causes of lightning outage are subdivided into direct lightning strokes and induced lightning strokes, which are identified by the characteristics of the lightning overvoltage. In the past, lightning protection devices were directed mainly toward the latter, and attention has been focused on the installation of lightning protection devices, ground wires, and reinforcement of insulators. However, lightning outages continue to occur. Thus it is extremely important to clarify the fault characteristics of lightning surges and to study the effectiveness of various lightning protection devices by considering both direct lightning stroke and induced lightning stroke in order to prevent lightning outage in the future. In this research, the electromagnetic transients program (EMTP) has been applied to the direct lightning stroke, and the induced lightning outage analysis program for multiple conductor systems has been applied to the induced lightning stroke to study the effectiveness of lightning protection devices provided by combination of various lightning protection devices. The most effective lightning protection schemes are analyzed and evaluated based on verification tests on the full scale models as well as economic considerations.     

高速钢高温形变诱发析出的研究

本文探讨了高速钢在高温形变过程中碳化物析出的行为及奥氏体组织状态对析出的影响。用透射电镜和扫描电镜分析了不同热处理状态奥氏体的组织结构,分析了高温形变过程中碳化物析出的部位,颗粒尺寸及形态。试验表明, 碳化物主要在奥氏体的缺陷处呈点状和点列状析出,大小为20mμ。处于回复状态的奥氏体缺陷诱发碳化物析出,析出碳化物钉札缺陷阻止再结晶进行。当再结晶驱动力较大时,由于动态再结晶充分发展,使缺陷大量消除,碳化物析出显著地减少。     

Ionoluminescence decay measured with single ions

A new ion beam analysis-based, single ion technique called the time to first photon has been developed to measure the decay of the luminescence signal of phosphors. Such measurements are currently needed to study luminescence decay mechanisms following high-density excitations and to identify strongly luminescent phosphor coatings with short lifetimes for ion photon emission microscopy (IPEM). The samples for this technique consist of thin phosphor layers placed or coated on the surface of PIN diodes. Single ions from an accelerator strike this sample and simultaneously create ion beam induced luminescence (IBIL) from the phosphor that is measured by a single-photon-detector, and an ion beam induced charge collection (IBICC) signal in the PIN diode. In this case, the IBICC signal provides the start pulse and the IBIL signal the stop pulse to a time to amplitude converter. It is straightforward to show that this approach also measures a signal proportional to activity versus time with an accuracy of 5% as long as the number of detected photons per ion is less than 0.1, which usually requires the use of absorbers for the IBIL detector or electronic discrimination for the IBIL signals. Details of the new analysis are given together with examples of luminescence decay measurements of several ceramic phosphors being considered to coat IPEM samples. IPEM is currently being developed at Sandia National Laboratory (SNL), the University of North Texas in Denton, and the Universities and INFN of Padova and Torino.     

Measurements of turbulent mass transport of a circular wall jet

The results of a laboratory investigation on the turbulence characteristics of a circular three-dimensional turbulent wall jet are presented. Measurements were taken up to 50 nozzle diameters using combined particle image velocimetry and planar laser induced fluorescence. The results showed that the induced turbulence was still evolving in the present range and had not achieved similarity. While the turbulent intensity for both velocity and concentration increased downstream, the turbulent mass transport showed a decline over distance for both the streamwise and spanwise directions, implying weakening dispersion from the jet core.     

水文自动测报系统防雷的探讨

水文自动测报系统若配备有线／无线（GSM，GPRS）双通道，可提高系统的可靠性，保证系统的畅通。然而，有线组网方式最致命弱点是防雷能力差，针对防雷问题，在实践中探讨其有效途径，论述接地装置的设计、安装中应注意的几个问题，并介绍在实践中电话线防雷从一级防护发展到三级防护，提高防雷的效果，有待在实践中，再认识，再提高。     

轴对称问题线元上分布奇点的诱导速度势和诱导速度

本文给出轴对称问题线元上高次分布源和偶极在无界域中的诱导速度势和诱导速度的计算公式,可供用分布奇点法求解轴对称势流问题时参考.     

An investigation of induced voltages to an underground gas pipeline from an overhead transmission line

This paper investigates induced voltage characteristics from an overhead transmission line by applying a method of modeling of induced voltages proposed by the authors. EMTP simulation results obtained by the modeling method agree with analytical results obtained from a well‐known formula. The induced voltages are significantly dependent on the configuration of the overhead line. A horizontal line induces the largest voltage in a gas pipeline, and the voltage induced by a vertical twin‐circuit line is about 20% smaller than that induced by a vertical single‐circuit line. The method is applied to a real pipeline system and the simulation results show reasonable agreement with field test results. © 2008 Wiley Periodicals, Inc. Electr Eng Jpn, 164(1): 43–51, 2008; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20465