基于局部分型面的电器外壳注塑模具设计

电器外壳制品形状结构复杂,有两处侧凸(孔)较难处理。通过对矩形孔内侧凸的结构分析,在其局部设计了分型面,避免了使用侧向抽芯机构;对侧孔部位设计了斜顶杆侧向抽芯机构,其结构简单、紧凑。模具采用一模二腔、平衡式布局,采用经扁推杆由制品内部进料的潜伏式浇口,S型流道。在NX 8.0中完成了模具结构设计。经实践证明,该模具结构合理,产品合格。     

石化装置蒸汽发生系统的仪表工程设计

主要探讨了某石化装置蒸汽发生系统的仪表工程设计，提出了复杂控制方案、联锁方案设计，同时也详述了影响系统设计的因素，如测量补偿和迁移等。     

PVC四通管注射模设计

介绍了PVC四通管注射模设计 ,阐述了弯型芯的旋转抽芯过程以及模具顶出、回程及冷却系统设计。实践证明 ,该模具结构合理 ,生产的塑件可以满足设计要求     

2×750 m3高炉冷风保安系统

介绍了2×750m3高炉冷风保安系统工艺流程、设计选型计算、可行性分析及实施效果。     

KYN44-12型中置柜联锁装置的改进设计

介绍了12kV中置柜联锁装置的设计原则,分析了现有中置柜联锁装置在实际运行中存在的问题和不足,提出了改进和完善中置柜联锁装置的设计方法。实际应用表明,改进后的中置柜联锁装置的功能更加完善,安全性更加可靠,完全达到了五防闭锁要求。     

Curing behavior and mechanical behavior of fully and semi-interpenetrating polymer networks based on polyurethane and acrylics

Polyurethane (PU) was made by reacting stoichiometric equivalent of trimethylol propane (TMP) and desmodur L. Fully interpenetrating polymer networks (fully IPN's) of various compositions based on PU and poly(ethylene glycol) diacrylate (PEGDA) were prepared by blending various ratios of PU/PEGDA, and cured by benzoyl peroxide (BPO). Semi-interpenetrating polymer networks based on PU and poly(ethylene glycol) monomethyl ether of acrylate (PEGMEA) were prepared in a similar way. Shift of exothermic peaks during IPN formation were examined with dynamic DSC. Viscosity increases were investigated with a Brookfield RVT type viscometer. Dynamic mechanical properties were probed via a rheometric dynamic spectroscopy (RDS).Expermintal results revealed a good compatibility of both IPN systems, as evidenced from the single damping peak of the RDS curves for each composition. Shifts of exothermic peaks to higher temperatures during the formation of fully IPN were observed, especially for the composition of PU/PEGDA = 50/50, which showed an exothermic peak at the highest temperature. Experimental results also revealed delayed viscosity increases and decreased gel fractions for all fully IPN's. On the contrary, the semi-IPN did not exhibibt similar phenomena. All these findings supported an effect of network interlock during fully IPN formation. The existence of a network not only provided a sterically hindered environment, but also restrained the chain mobility of the growing network, and vice versa, thus retarding the curing rates of both networks. Network interlock also broadened the width of the half damping peak, T_1/2, and subsequently led to improved mechanical properties such as the impact resistance and Young's modulus of fully IPN material.     

ECS-100 DCS控制系统在离子膜制碱装置中的应用

介绍某公司引进的离子膜制碱装置采用国产DCS系统的原由，系统的结构及特点。详细论述ECS-100 DCS在装置的特殊控制、顺序控制、联锁等方面的应用情况。     

催化裂化装置自保的改进方案

介绍催化裂化装置自保系统,以及自保系统的校验与维护。     

大型化肥厂燃煤锅炉DCS控制系统

详细介绍燃煤锅炉ＤＣＳ控制系统的配置情况，并着重分析燃烧控制系统的组态回路。论述ＣＥＮ－ＴＵＭ－ＸＬ的重要功能及其在生产中的重要地位。     

杯盖内衬塑料注射模设计

分析了磁化杯盖内衬塑件的工艺特点 ,介绍了适合于该塑件注射成型的特殊模具结构设计 ,同时说明了模具的工作过程。