磨料有序排布电镀砂轮的制备及其把持力研究

为解决电镀砂轮磨削加工中容屑空间不足的问题，采用点胶微粘接的方法制备了磨料有序排布的电镀砂轮，分析了磨料粘接效果和镀层力学性能。通过SEM分析了磨料/镀层/导电胶的结合界面，并进行了干磨削试验。研究结果表明，直径约为磨料粒径40%的胶点可粘接住磨料，单个胶点上粘接多颗磨料的占比小于6%；双脉冲电镀工艺制备的镀层显微硬度大于500HV，表层残余应力小于100MPa，磨料/镀层/导电胶之间的界面贴合紧密，无明显缺陷；砂轮在磨削时没有出现磨料脱落现象。     

Study on the non-uniform contact during ELID groove grinding

This paper introduces the potential feasibility that ELID (electrolytic in-process dressing) grinding replaces superfinishing in bearing manufacturing, but ELID grinding will bring new challenges. Different regions present distinguish surface profile due to the non-uniform contact in ELID groove grinding. However, few reports explaining the non-uniform contact are available. This article explores the mechanisms of the non-uniform contact during ELID groove grinding. Experiments on the non-uniform contact between bearing raceway and grinding wheel have been carried out under different conditions. The results show that non-uniform contact exists in ELID groove grinding process and it exerts influence on the profile of the raceway surface. Non-uniform contact influences the Rsk and Rku value all the time, but it influences the Ra value occasionally. Improvement strategies of eliminating the non-uniform contact are also discussed based on the experimental study.     

游梁式抽油机间歇供电装置的研制与应用

针对游梁抽油机电动机效率低和井场窃电问题,研制了具有节电和防井场窃电功能的游梁抽油机调压+间歇供电装置。该装置通过控制可控硅的导通角实现在电动机做功期调压供电,在电动机发电期不供电。分析了间歇供电对电动机、抽油机和电网的影响;根据现场实测数据分析了该装置的节电效果及现场应用情况。该装置节电效果显著,能防止井场窃电,可用于对游梁抽油机电动机的长期驱动。     

Simulation of Strength Distribution in Ground Ceramics by Incorporating Residual Stress Effect

Strength of ground ceramics may be affected by residual stress as well as surface flaws induced by grinding. Strength prediction for ground ceramics is convenient for mechanical design of ceramic components. In this article, a numerical procedure based on fracture mechanics was proposed to estimate strength distribution of ground ceramics by considering grinding-induced residual stress. Bending strength and residual stress of ground ceramics were measured for three grinding-conditions. By comparison of simulated results with experimental ones, it was revealed that strength characteristics in experiments were well simulated by using the proposed procedure.     

成形磨削中砂轮修整精度的研究

成形磨削一般采用金刚石笔来修整所需要的砂轮形状，金刚石笔在安装中的位置误差将影响被加工工件的精度，本文对此误差的大小进行了分析。     

在线磨辊辊面粗糙度的实验研究

影响轧辊表面粗糙度的因素很多，为此对影响辊面粗糙度的因素进行了系统分析和实验研究，得出了轧辊和砂轮的速度、砂轮粒度、砂轮直径及磨削液等主要因素对轧辊表面粗糙度影响的一般规律。利用回归分析的方法建立了轧辊表面粗糙度的数学模型，并将计算值与实测值进行了比较，发现两者基本一致。此项研究为适时控制冷轧带钢在线磨辊辊面粗糙度提供了计算模型。     

1 000 t/d湿磨干烧生产线工艺特点和调试

湿法生产线的技术更新改造有异地新建新型干法生产线和原地改成湿磨干法生产线二种。浙江虎山集团(?)3.0 m×88.68 m湿法线的改造,经方案比较和生产原料的状况,采用了湿磨干烧方案。其中,料浆脱水采用了真空吸滤法,浇成系统采用了南京院专有技术。改造投产后,获得了优质、高产、低耗和安全生产的技改效果。     

钢管打捆包装机的设计

为了提高包装质量，取代原人工打捆，设计开发了钢管打捆包装机，该包装机采用碾拉工艺，通过综合分析拉紧与绞纽组合动作的传动，实现了钢管的打捆包装机械化，使钢管包装质量达到了ISO9000标准要求，同时降低了劳动强度。     

Modified oil agglomeration process for coal beneficiation. III. Grinding and agglomeration using different szego mill designs

The simultaneous grinding/agglormeration process has been used to beneficiate Minto coal. Experiments with the Szego Mill, a planetary ring-roller mill with grooved rollers, have given good results. Different roller ridge/groove sizes have been tested and favourable oil-coal-water ratios established. Ash removal is closely related to grinding performance. Very short mill residence times, of the order of 10 seconds, are sufficient for microagglomerate formation. Considerable equipment and operating cost savings are possible with the modified process.     

磨机大齿轮对缝处产生张口的初探

针对大中型磨机大齿轮对缝处在使用中会产生张口现象而降低其使用寿命的问题,从分析产生张口的原因入手,通过理论计算,提出设计的配合间隙,并指出在安装与使用中应注意的问题.