在无铅环境中的热风整平

当电子工业走向无铅焊接的时候,热风焊料整平仍然是继续可焊性保护的优选方法。     

从PZT体系看无铅压电陶瓷的可能应用

总结了主要以(Bi0.5Na0.5)TiO3和NaNbO3为基的无铅压电陶瓷的性能，以Pb(Ti，Zr)TiO3基二元系、三元系压电陶瓷的性能与应用为参考，分析了无铅压电陶瓷可能的器件应用。此外，还对拓宽无铅压电陶瓷应用需要改进的性能提出了建议。     

Interfacial reactions in In-Sn/Ni couples and phase equilibria of the In-Sn-Ni system

The In-Sn-Ni alloys of various compositions were prepared and annealed at 160°C and 240°C. No ternary compounds were found; however, most of the binary compounds had extensive ternary solubility. There was a continuous solid solution between the Ni₃Sn phase and Ni₃In phase. The Sn-In/Ni couples, made of Sn-In alloys with various compositions, were reacted at 160°C and 240°C and formed only one compound for all the Sn-In alloys/Ni couples reacted up to 8 h. At 240°C, Ni₂₈In₇₂ phase formed in the couples made with pure indium, In-10at.%Sn and In-11at.%Sn alloys, while Ni₃Sn₄ phase formed in the couples made of alloys with compositions varied from pure Sn to In-12at.%Sn. At 160°C, except in the In/Ni couple, Ni₃Sn₄ formed by interfacial reaction.     

Low-cycle fatigue properties of eutectic solders at high temperatures

This paper details the deformation mechanism and low‐cycle fatigue life of eutectic solder alloys at high temperature (around 0.8T_m). Grain boundary sliding generally nucleates a wedge‐type cavity that reduces the low‐cycle fatigue life of metals. In this study, grain boundary sliding has promoted intergranular failure contributing to the reduction in fatigue life of Sn–Ag–Cu alloy. However, grain boundary sliding has exerted no deleterious effects on fatigue resistance of eutectic Pb–Sn and Bi–Sn alloys. The phase boundary sliding with very fine microstructure induces exceptional ductility in these alloys leading to superior low‐cycle fatigue endurance for theses eutectic Pb–Sn and Bi–Sn alloys.     

Effect of strain waveform on creep-fatigue life for Sn–8Zn–3Bi solder

This paper describes the creep‐fatigue life of Sn–8Zn–3Bi under push–pull loading. Creep‐fatigue tests were carried out using Sn–8Zn–3Bi specimens in fast–fast, fast–slow, slow–fast, slow–slow and hold–time strain waveforms. Creep‐fatigue lives in the slow–slow and hold‐time waveforms showed a small reduction from the fast–fast lives but those in the slow–fast and fast–slow waveforms showed a significant reduction from the fast–fast lives. Conventional creep‐fatigue life prediction methods were applied to the experimental data and the applicability of the methods was discussed. Creep‐fatigue characteristics of Sn–8Zn–3Bi were compared with those of Sn–3.5Ag and Sn–37Pb.     

低熔封接玻璃组成及其发展

综述了低熔封接玻璃的组成特点，给出了大量低熔玻璃组成实例，批出了低熔封接玻璃的封接低温化和无铅化发展方向，磷酸盐玻璃是首选组成之一。新的制备工艺和新的玻璃形成体系将对封接玻璃发展起着十分重要的作用。     

Effect of Cu concentration on the reactions between Sn-Ag-Cu solders and Ni

The reaction between the Sn-Ag-Cu solders and Ni at 250°C for 10 min and 25 h was studied. Nine different Sn-Ag-Cu solders, with the Ag concentration fixed at 3.9 wt.% and Cu concentrations varied between 0.0–3.0 wt.%, were used. When the reaction time was 10 min, the reactions strongly depended on the Cu concentration. At low-Cu concentrations (≦0.2 wt.%), only a continuous (Ni_1−xCu_x)₃Sn₄ layer formed at the interface. When the Cu concentration increased to 0.4 wt.%, a continuous (Ni_1−xCu_x)₃Sn₄ layer and a small amount of discontinuous (Cu_1−yNi_y)₆Sn₅ particles formed at the interface. When the Cu concentration increased to 0.5 wt.%, the amount of (Cu_1−yNi_y)₆Sn₅ increased and (Cu_1−yNi₆)₆Sn₅ became a continuous layer. Beneath this (Cu_1−yNi_y)₆Sn₅ layer was a very thin but continuous layer of (Ni_1−xCu_x)₃Sn₄. At higher Cu concentrations (0.6–3.0 wt.%), (Ni_1−xCu_x)₃Sn₄ disappeared, and only (Cu_1−yNi_y)₆Sn₅ was present. The reactions at 25 h also depended strongly on the Cu concentration, proving that the strong concentration dependence was not a transient phenomenon limited to a short reaction time. The findings of this study were rationalized using the Cu-Ni-Sn isotherm. This study shows that precise control over the Cu concentration in solders is needed to produce consistent results.     

环氧基的PCB对无铅组装的兼容性

综述了环氧树脂基的PCB与无铅化组装的兼容性问题。经过大量试验表明,常规的FR-4基材和双氰胺固化的高Tg基材是不能满足无铅化组装要求的,而采用酚醛固化的中等-Tg的环氧树脂基材是可能成为无铅化组装用基材的。同时,PCB制造过程也起着重要的作用。PCB设计和再(回)流焊的加热梯度也影响着无铅化的性能。     

Structural integrity in electronics

With continuing miniaturisation, increased performance demands and the requirement to remove lead from solder alloys, the challenges to structural integrity and reliability of electronic equipment are substantial and increasing. This paper outlines typical features in electronic equipment of which the structural integrity community may be generally unaware. Potential failure modes in service are described, and the problems of scale and material characteristics are considered. Progress in the application of fracture mechanics to the life prediction of interconnections is reviewed. The limited evidence available suggests that the crack growth resistance of silver‐containing lead‐free solders is superior to that of the traditional Sn‐37Pb under cycle‐controlled conditions but there is no difference when time‐dependent conditions prevail. In several respects, it is contended that the electronics sector is faced with challenges at least equivalent to those encountered in gas turbines and nuclear power generation.     

Microstructure and mechanical properties of Pb-free solder alloys for low-cost electronic assembly: A review

Lead-free solders, including Sn-58Bi, Sn-52In, and Sn-3.5Ag, are potential replacements for Sn-37Pb solder in low-cost electronic assembly. This paper reviews the literature on the microstructure and mechanical properties of these alloys. Because of the processing and testing conditions, many of the data are not predictive for electronic assembly applications. However, eutectic Sn-Bi seems to have properties approaching those of eutectic Sn-Pb under most conditions, while eutectic Sn-In seems far inferior in most respects. Eutectic Sn-Ag has many promising characteristics, but its relatively high melting temperature may preclude its use for this type of application.