Piezoelectric properties of PVDF-conjugated polymer nanofibers

This study presents the development and characterization of PVDF-conjugated polymer nanofiber-based systems. Five different conducting polymers (CPs) were synthesized successfully and used to create the nanofiber systems. The CPs used are polyaniline (PANI), polypyrrole (PPY), polyindole (PIN), polyanthranilic acid (PANA), and polycarbazole (PCZ). Nanofiber systems were produced utilizing the Forcespinning® technique. The nanofiber systems were developed by mechanical stretching. No electrical field or post-process poling was used in the nanofiber systems. The morphology, structure, electrochemical and piezoelectric performance was characterized. All of the nanofiber PVDF/CP systems displayed higher piezoelectric performance than the fine fiber PVDF systems. The PVDF/PPY nanofiber system displays the highest piezoelectric performance of 15.56 V. The piezoelectric performance of the PVDF/CP nanofiber systems favors potential for an attractive source of energy where highly flexible membranes could be used in power actuators, sensors and portable, and wireless devices to mention some.     

Influence of surfactants on rheological behaviors of polyacrylonitrile/dimethyl sulfoxide/silicon blending polymer solutions

KH550, KH560, CTAB, and F127 were adopted to modify silicon (Si) to improve the dispersity and stability of Si in the polyacrylonitrile/dimethyl sulfoxide (PAN/DMSO) polymer solutions. The influence of surfactants on rheological behaviors of PAN/DMSO/Si blending polymer solutions was investigated by an advanced solution and melt rotation rheometer. The homogeneity and stability were also studied. The results showed that the surfactants could change the viscosity dependence of blending polymer solutions on shear rate, temperature and storage time by increase the steric hindrance of Si. Among the four solutions, PAN/DMSO/Si blending polymer solution with F127 exhibited the lowest viscosity, activation energy and the smallest structural viscosity index and exhibited the trend close to the Newtonian fluids. Moreover, PAN/DMSO/Si blending polymer solution with F127 exhibited the best dispersity and stability, indicating its best physical properties and machinability.     

Teaching and Learning Electrochemistry

Numerous conceptual difficulties and misconceptions have been reported in the science and chemistry education literature about electrochemistry concepts such as electrolytes, redox equations, and about electrochemical (galvanic and electrolytic) cells. Other studies have considered teaching approaches aimed at improving learning and at overcoming misconceptions. This paper reviews these studies and considers strategies and approaches for the effective teaching of electrochemistry. Then, the review focuses on problem solving in equilibrium electrochemistry, especially problems involving the Nernst equation. The main findings of four studies with Greek university chemistry students, dealing with: (i) algorithmic problem‐solving ability; (ii) practice on problem solving; (iii) the effect of the format of a problem; and (iv) the construction and evaluation of a website devoted to electrochemistry problem solving, are reported.     

Study of planar structure applying reciprocity technique combined with MGEC and analysis of discontinuity

The 3D structure electromagnetic computation presents several difficulties related to the volume mesh. In fact, the entire volume space must be taken into account even the smallest details. In this article, we propose a formulation based on the reciprocity theorem combined with the generalized equivalent circuit method to model a planar 3D structure with both coaxial and planar excitation. The major advantage of this formulation is the fact to reduce the computational volume into 2D ones in the discontinuity plane. In addition, we focused on the calculation of the discontinuity between the excitation source and the planar structure to determine the exact behavior of the electric coaxial excitation model. The obtained current density, electric field distributions, and the input impedance are presented and discussed in the following sections. An approximately good agreement of input impedance with those obtained by the simulator and measurement is shown.     

Crosslinked quaternized poly(arylene ether sulfone) copolymer membrane applied in an electric double-layer capacitor for high energy density

The low energy density of supercapacitors, especially supercapacitors based on aqueous electrolytes, is the main factor limiting their application, and the energy density is closely related to the operating potential window of the supercapacitor. The polymer electrolyte is the main contributor to the safe operation and good ion conductivity of the supercapacitor. In this study, a crosslinked quaternized poly(arylene ether sulfone) (PAES) membrane was prepared via crosslinking during membrane formation with a thermal-only treatment and applied in an electric double-layer capacitor (EDLC). The pre-prepared PAES membrane formed a polymer electrolyte with 1 mol/L Li₂SO₄ and was then fabricated into an EDLC single cell. The properties of both the membrane and ELDC were investigated. The preferred cPAES-N-0.2 polymer electrolyte showed an ionic conductivity of 1.18 mS/cm. The optimized EDLC exhibited a single-electrode gravimetric capacitance of 104.92 F/g at a current density of 1.0 A/g and a high operating potential window (1.5 V); it, thereby, achieved a high energy density of 8.20 W h/kg. The EDLC also exhibited excellent cycling properties over 3000 charge–discharge cycles. The crosslinked structures promoted the tensile strength and thermal stability of the PAES membranes; this was accompanied by a slight decrease in the ionic conductivity. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 47759.     

凝汽器铜管FeSO4镀膜监测系统的开发

为了减缓凝汽器铜管的腐蚀，通常采用FeSO4造膜保护，而FeSO4膜质量很难控制，作者通过凝汽器铜管FeSO4镀膜成膜工艺，影响因素的深入研究，建立了以电化学响应为特征的镀膜控制系统，选择了相应的传感器，形成以计算机处理为核心的监测系统，应用表明，该系统方便，可靠。     

Electrochemical Aspects of Electroosmotic Dewatering of Clay Suspensions

An attempt is made to elucidate the electrochemical aspects of the electroosmotic dewatering (EOD) of clays as reported in some recent work, especially that on interrupted DC power electroosmotic dewatering published by Rabie, Mujumdar and Weber (2). These authors showed that the dewatering by EOD stops after the DC power has been on for several minutes or hours; on interruption of their power and on short-circuiting of the electrodes, conditions can be created again for some further dewatering by DC power EOD. This discovery, of Rabie et al. is interpreted as a fuel cell effect and it is shown that it affords clues to several other electrochemical strategies for the possible enhancement of the efficiency of the EOD by DC power.

Further, the open circuit potentials observed by Rabie et al. (2) on the interruption of DC power are given an electrochemical interpretation which leads to quantitative estimates in agreement with the experimental values.     

添加剂对尖晶石型锰酸锂性质表征的影响

以LiOH·H_20和MnO_2为原料,分别掺入H_2BO_3、Al_2O_3、SiO_2和P_2O_5等添加剂,用固相分段法制备尖晶石型锰酸锂。结果表明,SiO_2和P_2O_5可以有效地改善LiMn_2O_4的电化学性能,H_3BO_3对锰酸锂的电化学性能影响不大,而Al_2O_3破坏了LiMn_2O_4的电化学性能。面扫描结果显示,Si或P元素各自都均匀地分散于LiMn_2O_4的物相中。从元素电负性和原子半径的角度分析了B、Si、P和Al元素对尖晶石型LiMn_2O_4结构和性能的影响。     

油气田开发中的CO2腐蚀及防护技术

综述了二氧化碳均匀腐蚀和局部腐蚀的机理，分析了二氧化碳腐蚀的各种影响因素，并对二氧化碳腐蚀的防护技术进行了概括，着重介绍了缓蚀剂防护技术研究进展，并提出了研究CO2腐蚀及其缓蚀剂应注意的几个问题。     

Ti基MnO_x型DSA析氧电极材料的性能

本文报导了新型 Ti/SnO_2+MnO_x+RuO_2/MnO_x(DSA)电极材料的各种性能,其中包括电极的导电性、表面粗糙度、电化学活性表面积、析氧阳极特性等,并用 X 射线衍射法进行了物相分析、用 SEM观察了表面形貌。确认该电极性能良好,加之成本较低,可作为酸性介质中的析氧电极材料。