The Structure of the Irreversibly Bound Adhesion Promoter-Substrate Interfacial Layer of γ-Aminopropylsilanetriol on Crystalline Si, as Measured by XPS and FTIR

The irreversibly bound interfacial layer deposited by the γ-aminopropysilanetriol adhesion promoter onto a crystalline silicon substrate, which remains even after profuse washing, was found by XPS to have resulted from the fragmentation and rearrangement of the original γ-aminopropylsilanetriol molecule. A mechanism is proposed, involving the homolytic scission of the terminal N-C bond. One of the subsequent reactions is believed to involve hydrogen loss by abstraction and the formation of a terminal vinyl group, which bonds to the substrate. Support for this mechanism is found in IR spectroscopy of this layer.     

The Interlaminar Bond Strength of Flexible Polymer-Metal Laminates

An alternative test method to the traditional 180° “T” peel test has been developed for the measurement of interlaminar bonding in three-ply (polyester/aluminium/polypropylene) flexible-packaging, laminate materials. The new test is thought to involve mixed mode I (opening) and mode II (shearing) failure, and takes into account the yielding of the polypropylene layer during testing. The method allows more direct comparisons between materials to be made, and allows the measurement of strong bonds, where a peel test would result in yield or fracture of the substrate arms before debonding.     

家电卷材涂料用HDI改性聚酯树脂的研制

以己二异氰酸酯（HDI）改性聚酯树脂与氨基树脂配制成家电用卷材涂料。阐述了氨酯键对涂膜性能的贡献。探讨了HDI用量对涂膜性能的影响。     

Compressibility of the polymer crystal

Results for the compressibilities of a wide range of polymer crystals along the fibre- and the transverse crystal axes are presented. Good agreement is found between the theoretical and the experimental results of different authors.     

聚醚型聚氨酯的氢键、微相分离及性能

用本体一步法合成了5种不同硬段含量(11.0％～46.9％)的二苯甲烷-4,4′-二异氰酸酯/环氧乙烷封端型聚环氧丙烷聚醚/乙二醇的聚醚型聚氨酯,并借助于IR,DSC,DMS和材料试验机等手段对该聚氨酯的氢键、微相分离及力学性能进行了表征。结果表明:随着硬段含量的增加,其>NH与微区中的>C=O的氢键化程度逐渐提高,软段微区中—O—的氢键化程度逐渐降低;微相分离程度逐渐提高;拉伸强度及硬度随之增加,扯断伸长率在硬段含量40％左右出现极大值。     

Effects of apitong (Dipterocarpus spp.) extractives on bond strength development and curing rate of adhesives

Emulsion polymer isocyanate ( ), polyvinyl acetate ( ) and resorcinol-formaldehyde ( ) adhesives were used to produce single lap shear specimens using resinous and non-resinous apitong (Dipterocarpus spp.) timbers. Tests showed that joints made with highly resinous apitong were about 40% weaker than similar joints made with non-resinous apitong. The resinous apitong was treated with different solvents to yield five different extractives which were characterized by infra-red analysis. Apitong extractives were then added to and adhesives and joints made with buna (Fagus crenata), a timber known to be low in extractives and easy to bond. Joints prepared using extractive-containing adhesives were generally weaker than those made with the unmodified adhesives. RF adhesives containing extractives cured more slowly than unmodified . It is thought that the acidic nature of the extractives changes the pH of the system sufficiently to affect the curing mechanism     

无烟煤熔融盐催化气化反应特性研究

根据煤催化气化原理及熔融盐特性,设计了一套小型熔融盐催化煤气化实验装置。针对无烟煤燃烧特性差的特点,在实验中研究了温度和二氧化碳流量对气化结果的影响,并对影响机理进行分析。     

Corrosion resistance of austenitic stainless steel separator for molten carbonate fuel cell

STS310S and SC-STS310S (simultaneously co-deposited chromium and aluminum onto 310S austenitic stainless steel substrate by pack-cementation process) were used as separator materials on the cathode side of a molten carbonate fuel cell. With the STS310S, corrosion proceeded via three steps; a formation step of unstable corrosion product, a protection step against corrosion until breakaway, and an advance step of corrosion after breakaway. The final corrosion product was LiFeO₂ and the loss of mass was 6.5 mg/cm² after a corrosion test of 480 hr at 650°C. The SC-STS310S showed more effective corrosion resistance, however, than did common STS310S. There was especially no corrosion loss on the SC-STS310S after the 480 hr corrosion test. It is anticipated that it will be very useful as an alternative separator on the cathode side off the MCFC in the future.     

三元硝酸熔盐高温粘度的计算

三元硝酸熔盐是一种重要的传热蓄热介质,粘度物性数据对其在工业中应用非常重要.但是由于硝酸熔盐熔点高,腐蚀性强,测试条件苛刻,粘度测量结果偏差较大,故利用计算方法确定熔盐粘度.本文首先通过大量实验数据拟合了纯物质KNO3,NaNO3和NaNO2的粘度,再利用Arrhenius混合规则确定的经验公式计算三元硝酸熔盐的粘度.与前人实际测量值进行比较.结果发现:利用简单经验公式估算的结果与实际测量值比较接近,表明这种熔盐热物性变化受外界影响较小,可以利用Arrhenius简单混合规则确定熔盐粘度.     

Recent development and applications of an optical method for measurements of thermophysical properties

The experimental determination of thermophysical properties has been greatly improved by the introduction of laser technology. The laser beam is used for sensing and also for heating (or exciting) the specimen. The advantage of using a laser beam is most strongly felt in the measurement of the thermal conductivity or the thermal diffusivity, which are some of the most difficult properties to measure. Interesting features of new techniques for investigating various aspects of thermal conductivity in fluids and solids are reviewed. An optical method, the so-called forced Rayleigh scattering method, or the laser-induced optical-grating method, has been developed and used extensively by the present author's group. The method is a high-speed remote-sensing method which can also quantitatively detect anisotropy, namely, direction dependence of heat conduction in the material. It was used for determination of the thermal diffusivity and its anisotropic behavior for high-temperature materials such as molten salts, liquid crystals, extended polymer samples, and flowing polymer melts under shear. Interesting applications of the method were demonstrated also for thermal diffusivity mapping and microscale measurement.Invited paper presented at the Twelfth symposium on Thermophysical Properties, June 19–24, 1994, Boulder, Colorado, U.S.A.