An investigation into the effect of various chemical and physical treatments of a South African phosphogypsum to render it suitable as a set retarder for cement

The work describes various physical and chemical treatments to eliminate the deleterious effects of impurities in phosphogypsum on the delayed setting time and impaired strength development behaviour of cement to which it was added as a set regulator. The physical treatments included washing, milling, and ultrasonic treatment of the material, while the chemical treatments dealt with acidic and basic additions to the phosphogypsum during the washing stage. It was found that chemical treatment with a milk of lime solution, which is often recommended in literature, was ineffective in reducing set retardation. Treatment with ammonium hydroxide or sulphuric acid was more effective in this regard. Intergrinding phosphogypsum with slaked lime improved its effectiveness in reducing set retardation, but the use of unslaked lime was less effective and also resulted in marked reductions in compressive strengths. A combined treatment of wet milling phosphogypsum with a lime slurry in a ball mall was derived from these experiments and is recommended for full-scale plant applications.     

NaY晶化母液制备硅铝胶的技术探讨

在导向剂法合成Y型分子筛的工艺下，晶化母液中SiO₂的含量为50～55g/l,Na₂O含量为20～25g/l，相当于模数为1.65～2.58的稀水玻璃，将晶化母液分离处理后，在晶化母液中加入一定量的硫酸铝溶液使硅沉淀,经过滤和水洗后即可制备出合格的硅铝胶，以便进行重新利用。     

硅钢片模具设计及其线切割加工

论述了电磁铁铁芯 (硅钢片 )模具的设计要点及其线切割加工的技巧 ,提出了提高模具加工精度和使用寿命的有效措施。     

大方坯连铸机离线检修设备对中台的改进与完善

介绍了大方坯连铸机离线设备对中台及样规的改进方案.改进后,大大缩短了设备检修时间,降低了工人的劳动强度.     

PTC热敏电阻的现状与发展趋势(续一)

基于对1995年以来,国内外PTC热敏电阻的研究,介绍了PTC热敏电阻用原料(BaCO3、TiO2、BaTiO3、SrCO3、PbO、Pb3O4、SrTiO3、PbTiO3、Y2O3、Nb2O5、CaCO3、SiO2等);材料(BaTiO3系、V2O3系及高分子);生产技术(瓷粉制造、烧成、芯片制造、质量评定、理化分析、片式PTC生产);重点产品(消磁、马达启动、限流及加热等用)以及基础研究(相变应力模型、表面势垒模型)等方面的现状及今后的发展趋势。     

Monoacylglycerols derived from butter oil by Penicillium roquefortii in suspension cultures

Structural isomers of monoacylglycerols (monoglycerides, MAGs) were identified and compared after degradation of butter oil by two strains of Penicillium roquefortii and a commercial lipase from P roquefortii (EC 3.1.1.3) at pH 7.0 and 10 °C. The conditions were selected as they were comparable with those used in the manufacture of blue mould‐ripened cheese. The commercial lipase was selected to compare with the fungal strains in terms of acyl migration. Results showed that the main isomers formed by lipolysis with the commercial lipase were sn‐2 MAGs (64 mol%), whilst spores and emerging mycelia of P roquefortii produced mainly sn‐1(3) MAGs (83–90 mol%). The work reported here may lead to further assessment of different MAG structural isomers as natural preservatives in foods and dairy products. © 2002 Society of Chemical Industry     

Viscosity estimation for slags containing calcium fluoride

Based on recently published experimental data, the Riboud model was modified for viscosity estimation of the slags containing calcium fluoride. The estimated values were in good agreement with measured data. Reasonable estimation can be achieved using the modified Riboud model for mould fluxes and ESR (eletro slag remelting) slags. Especially for ESR slags, the modified Riboud model can provide much more precise values than the original Riboud model.     

滑模施工在尼尔基厂房混凝土工程中的应用

尼尔基水利枢纽发电厂房的混凝土施工中，对闸墩和胸墙等部位的混凝土采用了滑模施工工艺，这样既加快了厂房施工进度，也保证了施工质量，挽回了发电厂房总体滞后的施工进度，取得了良好的效果，值得推广和借鉴。     

Method to Characterize the Air Flow and Water Removal Characteristics During Vacuum Dewatering. Part II—Analysis and Characterization

This is part II of a study reported earlier on a method to characterize the air flow and water removal characteristics during vacuum dewatering. This article presents experimental data and analysis of results from the use of a cyclically actuated vacuum dewatering device for removing moisture from wetted porous materials such as paper with the intermittent application of vacuum and accompanying air flow though the material. Results presented include sheet moisture content as a function of residence time and hence water removal rate under a variety of process conditions. Also, experimental results on air flow through the wet porous structure and hence the role and importance of air flow during vacuum dewatering are presented. Vacuum dewatering process conditions include exit solids content between 11 and 20% solid under applied vacuum conditions of 13.5 to 67.7 kPa (4 to 20 in. Hg). Regression analysis indicated that the exit sheet moisture content exhibited a nonlinear relationship with residence time with exit solids reaching a plateau after a certain residence time. Final moisture content correlated linearly with the average overall flow rate of air through the paper sample and the basis weight of the material.