硅钢片模具设计及其线切割加工

论述了电磁铁铁芯 (硅钢片 )模具的设计要点及其线切割加工的技巧 ,提出了提高模具加工精度和使用寿命的有效措施。     

大方坯连铸机离线检修设备对中台的改进与完善

介绍了大方坯连铸机离线设备对中台及样规的改进方案.改进后,大大缩短了设备检修时间,降低了工人的劳动强度.     

Monoacylglycerols derived from butter oil by Penicillium roquefortii in suspension cultures

Structural isomers of monoacylglycerols (monoglycerides, MAGs) were identified and compared after degradation of butter oil by two strains of Penicillium roquefortii and a commercial lipase from P roquefortii (EC 3.1.1.3) at pH 7.0 and 10 °C. The conditions were selected as they were comparable with those used in the manufacture of blue mould‐ripened cheese. The commercial lipase was selected to compare with the fungal strains in terms of acyl migration. Results showed that the main isomers formed by lipolysis with the commercial lipase were sn‐2 MAGs (64 mol%), whilst spores and emerging mycelia of P roquefortii produced mainly sn‐1(3) MAGs (83–90 mol%). The work reported here may lead to further assessment of different MAG structural isomers as natural preservatives in foods and dairy products. © 2002 Society of Chemical Industry     

Viscosity estimation for slags containing calcium fluoride

Based on recently published experimental data, the Riboud model was modified for viscosity estimation of the slags containing calcium fluoride. The estimated values were in good agreement with measured data. Reasonable estimation can be achieved using the modified Riboud model for mould fluxes and ESR (eletro slag remelting) slags. Especially for ESR slags, the modified Riboud model can provide much more precise values than the original Riboud model.     

板栅模具设计中的几个问题

通过对板栅模具设计中遇到的几个实际问题的分析提出处理意见 ,从而达到科学合理地设计板栅模具。     

基于B/S模式矿山管理信息系统构建技术研究

在全面分析以往矿山管理信息特点的基础上，提出了基于B／S模式开发矿山信息系统的思路。对基于B／S模式开发矿山信息系统的关键技术及开发步骤进行了详细的介绍。     

天铁炼钢厂四流中间包流场的水模实验及优化

介绍了天铁炼钢厂中间包水模实验原理和过程，分析了斜、直、圆三种型式挡渣墙模拟结果，提出了合理的挡渣控流方案，在生产实践中使用效果良好。     

铸造Ti—0.2Pd合金SF—1000双级风机叶轮的研制

Ｔｉ－０．２Ｐｄ合金ＳＦ－１０００双级风机叶轮是大型盐酸再生设备的主要部件，采用整体铸造方法制造，无论在技术上还是经济上都是十分有利的。本文主要介绍采用加工石墨，铸铁组合型，真空电弧凝壳熔炼铸造工艺，成功地研制出整体铸造风机叶轮。     

基于注塑件收缩率预测的模具型腔尺寸生成方法研究

针对注射模具CAD/CAM系统普遍采用平均收缩率来计算模具型腔尺寸所存在的不足，提出基于注塑件的收缩率预测结果生成模具成型尺寸的方法，并给出注塑件尺寸与模具成型尺寸之间的换算方法。最后通过反求工程中的曲面重构技术完成模具型腔表面的造型。