Simulation of Strength Distribution in Ground Ceramics by Incorporating Residual Stress Effect

Strength of ground ceramics may be affected by residual stress as well as surface flaws induced by grinding. Strength prediction for ground ceramics is convenient for mechanical design of ceramic components. In this article, a numerical procedure based on fracture mechanics was proposed to estimate strength distribution of ground ceramics by considering grinding-induced residual stress. Bending strength and residual stress of ground ceramics were measured for three grinding-conditions. By comparison of simulated results with experimental ones, it was revealed that strength characteristics in experiments were well simulated by using the proposed procedure.     

Eigenspannungen als Messgröße zur Qualitätssicherung

Residual stress as measured quantity in quality assurance The x‐ray method is used in the Volkswagen Automotive Group at different world‐wide locations as a standard procedure to determine residual stress. As an important measured quantity in the quality assurance residual stresses are specified in drawings of different components (e.g. gears, coil springs). Measurements are carried out during quality assurance, production, damage analyse, technical development department and design control of components from suppliers. An optimum efficiency can be achieved, if it exists a unique correlation between residual stress values and loading capacity of components, and if the processes to introduce residual stress can be optimized using residual stress measurements during the production.     

苏北-南黄海盆地构造演化

苏北及南黄海盆地是由多期、多类盆地叠加的复合残留盆地,地质概况基本相似,成因演化近同,自元古界下扬子板块形成后,主要经历了古-中生代地台、中生代前陆盆地、走滑拉分盆地时期以及新生代断陷、坳陷盆地时期.在古生代-中生代发展过程中是一个整体,晚白垩世盆地演化出现分化,发育伸展盆地群,形成一系列叠置在中、古生代盆地之上的箕状断陷,箕状断陷的发育及分布明显受中-古生界内部先存逆冲断裂的控制.     

Life Calculations for Header – PGV-1000 Steam Generator Connector Weld Joints under NPP Service Conditions

The procedure for calculating the life of header – steam generator connector weld joints is proposed. It allows for running out the material plasticity reserve upon static cyclic elastoplastic loading as well as operating conditions, local stress concentrations, and residual stresses after welding.     

UHE电炉炼钢的冶炼工艺特点及其发展的几个问题

从实践上论述了UHE电弧炉炼钢的工艺特点,提出UHE电炉的“新三期”的新观点,并作了定量的描述;对正在发展中的UHE电炉工艺与设备提出了策略性的意见.     

柔性冗余度机器人残余振动主动控制

研究柔性冗余度机器人的残余振动主动控制问题，设计了具有压电作动器与应变传感器的机敏杆件，建立了受控系统的状态空间表达式，采用独立模态空间控制理论设计LQR状态反馈控制器，并基于对偶原理设计了具有指定收敛特性的Luenberger全维状态观测器，最后，以平面3R柔性冗余度机器人为例进行了计算机仿真，结果表明，采用这种主动控制方法可以显著改善柔性冗余度机器人的动力学品质。     

Peculiarities of erosion-corrosion processes

Investigations have been carried out on an erosion-corrosion apparatus to investigate the behaviour of corrosion-resistant highalloy iron-base materials containing hard phases. These materials had been optimized for increased wear resistance under complex stress conditions. As expected, in dry erosion tests, very low mass losses were established; there was little difference between the materials. Also, in corrosive environments (NaCl, H₂SO₄), the materials showed good stability; however, the duplex structures were superior to the martensitic ones. The combination of erosion and corrosion produced large differences and, in some cases, markedly reduced resistance to damage. These results confirmed observations that it is impossible to deduce the environmentally influenced mechanical behaviour of an alloy from its behaviour in separate corrosion and erosion experiments. The basic mechanisms underlying these processes have been investigated only tentatively.     

Residual Stress Simulation of Injection Molding

In this study, distribution and history of residual stresses in plaque-like geometries are simulated based on linear thermoviscoelastic model, which helps to understand the mechanics and evolution of the residual stresses in the injection molding process. The numerical calculation of direction, combined with the specified boundary conditions. Results show that the stress variation across the thickness exhibits a high surface tensile value changing to a compressive peak value close to the surface, with the core region experiencing a parabolic tensile peak. Residual stress distribution throughout the thickness is almost same along the flowpath and the final residual stresses value near the gate is lower than the value near the end of flowpath.     

Structure modification of rapidly solidified Al-11 wt% Si alloy by the addition of 2 wt% Fe

An investigation of the structure formation of as-cast Al-11 wt% Si (AlSi11) and Al-11 wt% Si-2 wt% Fe (AlSi11Fe2) rapidly solidified (RS) ribbons is performed. Ribbon samples are examined in detail using Auger electron spectroscopy (AES) and transmission electron microscopy (TEM). A nanoscale thickness layer of Si-precipitations, at both Al-grains boundary and oxide/Al-matrix interface, is found to be characteristic for “pure” AlSi11 ribbons. For Fe-doped ribbons, this layer comprises Fe-containing phase also, which appears to possess amorphous nature and is situated between the Si-grains and Al-matrix. A possible mechanism of altering the thermally activated volume diffusion of elements, due to the effect of Fe on the structure modification, is speculated based on the obtained results.