岩石物理横波速度曲线计算技术

横波速度是地震勘探中的重要参数。针对实际生产中缺乏横波速度测井曲线资料，利用经验公式计算精确度不高的问题，通过对横波速度计算理论模型的研究分析，选择Blot-Gassman模型法，利用岩石矿物成分、流体成分、孔隙度及密度等测井曲线进行横波速度测井曲线的计算，并对横波速度计算技术和流程进行研究。在实际工区进行了横波速度曲线计算，计算结果与实测横波吻合程度较高，误差小于10％，该技术在储层和流体识别预测的应用中取得了较好效果。     

滚动式冷床在高钢级油管生产线中的应用

根据石油开采业对石油机械产品的需求 ,利用机械理论基础知识 ,通过实践设计 ,提出了对几何尺寸长的金属管类进行调质处理后的均匀冷却方法 ,以满足其性能要求。     

δ－Al_2O_3纤维／Al－12Si复合材料室温拉伸强度分析

对δ－Ａｌ２Ｏ３纤维／Ａｌ－１２Ｓｉ复合材料室温拉伸强度的分析表明，在实验条件下该复合材料存在δ－Ａｌ２Ｏ３纤维的最小体积分数Ｖｍｉｎ和临界体积分数Ｖｃｒｉｔ，并求出其基体强度σ＇ｍ和室温强度σｃ－δ－Ａｌ２Ｏ３纤维体积分数Ｖｆ直线方程及纤维的临界长度ｌｃ和复合材料的剪切应力τｉ．确定复合材料的ＲＯＭ预测曲线，应首先判断σ＇ｍ是否等于未增强合金的强度σｕｍ才能得出正确的结论     

具有细小组织的高强度和高延性钢管的开发

介绍了日本川崎制铁公司技术研究所开发出的电焊钢管采用热张力减径工艺的特性 ,及这种钢管的高强度、高延性等基本特性。用这种钢管制造的汽车零部件 ,经弯曲、冲击和疲劳特性等实验 ,证明具有良好的机械加工性能 ,是制造汽车用零部件的优良材料。     

提高自蔓延高温合成陶瓷内衬钢管性能的研究

在概括了自蔓延高温合成陶瓷内衬钢管的制备原理基础上，从降低陶瓷层孔隙率，减少陶瓷层裂纹和提高陶瓷层结合强度等方面，论述了提高自蔓延高温合成陶瓷内衬钢管性能的措施，对自蔓延高温合成陶瓷内衬钢管的应用现状及展望进行了评述。     

The suitability of round clinching tools for high strength structural steel

The use of light gauge steel framing is increasing rapidly. New methods for joining frames are being sought. One of the most promising methods is clinching. Clinching has been used for almost 20 years. There has been much research into the method, the tools, suitable materials and applications. Few articles have been published concerning clinching of high strength structural steels, which are currently the most relevant materials for house construction.This study included 11 different clinching methods. In total, 469 test pieces were produced. Despite the high strength of the materials, all the clinching methods that were examined could be used satisfactorily. The most significant result was that a round tool is appropriate for all the materials tested. In fact, in comparison with results obtained using other types of tool, when the methods were ranked by maximum shear load capacity, the round design appeared in the top three classes seven times out of nine.     

摩擦强度对薄膜表面形态的作用:原子力显微镜下的观察

展示了摩擦强度对聚酰亚胺薄膜表面形态的影响，原子力显微图像显示，机械摩擦会使聚酰亚胺薄膜表面上形成微沟槽，这些沟槽的表面具有丰富的表面精细构造。原子显微图像还揭示了机械摩擦可以改变被磨擦聚酰亚胺膜的表面形态。     

Effects of solidification structure on fatigue crack initiation and fatigue strength in Al−Si−Mg cast alloys

Rotating-bending uniaxial fatigue tests and micro-fatigue crack initiation tests were carried out using a permanent mold cast (PMC) and semi-solid die cast (SDC) with Al−7%Si−0.35%Mg composition in order to examine the relationship between solidification structures and fatigue behaviors. The crack length was measured using a replication method. Fatigue strength was improved in SDC, which was almost consistent with the predicted fatigue strength using the size of Si particle cluster. Resistance to fatigue crack initiation and fatigue strength were improved in SDC owing to the finer Si cluster and to higher ultimate tensile strength. Fatigue crack in PMC was preferentially initiated at pores. For SDC, the fatigue crack was initiated at the Si particle/matrix interface, and then sucessively grew along eutectic cell boundaries.     

纤维混凝土在水工建筑工程中的应用(上)

概述改性混凝土垢发展情况，介绍纤维混凝土在国内外水工建筑物上的应用实例，提出钢纤维增强钢筋混凝土水工建筑结构强度计算方法。包括受弯构件正截面强度，斜截面抗剪强度的计算；重点介绍了网状钢纤维增强混凝土（FOC）在水工建筑物上的应用，包括在渡槽，闸门，小型拦河坝，轻型岸型等工程上的应用实例，T新梁正斜截面的强度计算，板材承载力计算的方法。     

TP130TT高抗挤套管研究与应用

为了提高盐层段固井质量 ,中原油田研究开发了 TP130 TT高抗挤套管 ,性能试验评价表明 ,其抗挤强度超过 16 0 MPa,并给出了其固井质量评价标准。在中原油 346口井中的应用表明 ,该套管有效地解决了盐层段套管损坏问题 ,延长了油气水井寿命 ,经济效益和社会效益显著。