用于远程激光测距机的板条激光器

研制了用于远程激光脉冲测距机的板条激光器。使用半导体泵浦的MOPA激光结构实现了大于250 mJ的脉冲激光输出,输出脉冲宽度为12.83 ns,最终输出激光光束束散角为0.18 mrad。该激光测照器可应用于远程激光测距。对激光测距机的测距与照射能力进行了理论计算与分析。理论分析表明,应用于机载平台时,该激光测照器能够实现50 km距离的激光测距。该型激光测距机具有测距距离远,重量轻,结构紧凑等特点,具有广泛的应用前景。     

寒冷地区高温干燥条件下混凝土面板裂缝控制

希尼尔水库位于新疆巴音郭楞蒙古族自治州境内，气候特点为高温、干燥、冬季寒冷。根据混凝土面板产生裂缝的原因，并结合工程区的气候特点，认为控制面板的塑性收缩、干缩与冷缩裂缝是防止裂缝产生的重点。通过采用高性能混凝土，合理的养护措施(微喷灌洒水技术)，有效地防止了裂缝的产生，保证了工程质量。     

射频板条CO_2激光器并联谐振技术的研究

本文利用周期性网络模型计算了射频板条CO2激光器电极的纵向电压分布．探讨了并联谐振技术在板条器件中获得成功运用的原因．提出了利用并联谐振技术进一步提高电压分布均匀性的两个途径．     

广钢转炉分厂2号方坯连铸机拉速问题的探讨

通过分析钢水在结晶器内凝固的不均匀性及对钢水结晶的热量平衡计算，讨论连铸中间包钢水温度、结晶器冷却水流量及进出水温差对拉坯速度的影响。     

大方坯连铸机离线检修设备对中台的改进与完善

介绍了大方坯连铸机离线设备对中台及样规的改进方案.改进后,大大缩短了设备检修时间,降低了工人的劳动强度.     

峡口水库沥青混凝土面板的施工与试验

以灌溉、防洪为主的峡口水库大坝，为沥青混凝土面板堆石坝，为研究低温抗裂性能，对沥青混凝土面板破损取样，进行了配比和多种力学性能试验，并与原面板设计指标进行了对比。由于面板经受住了－20℃以下的低温考验，其所用沥青指标、破损取样试验结果，特别是冻断低温指标，对确定水工沥青混凝土低温抗裂检验标准有重要参考价值。     

钢纤维喷射混凝土作为面板材料的可行性研究

钢纤维混凝土作为一种新型增强材料，以其较好的受力变形特性在水利水电，交通，海岸防护，港口及军事等诸多工程中得到了广泛的应用。针对混凝土面板堆石坝面板的受力变形特点，为改善水布垭面板堆石坝面板的受力条件，提高其防渗能力，同时方便施工，现提出采用钢纤维喷射混凝土作为水布垭面板堆石坝面板材料的新构想，并通过对钢纤维喷射混凝土的物理力学特性及堆石坝面板受力变形进行分析，为钢纤维喷射混凝土在水布垭面板堆石坝面板中的实际应用提出了建议方案。     

薄板坯连铸连轧流程Ti微合金化高强钢开发与应用

在薄板坯连铸连轧流程上，经过对Ti微合金化技术研究，有效解决了Ti微合金化强度性能波动大的问题，开发出屈服强度450～700MPa高强钢。对试制钢组织性能和工业应用分析研究，表明该产品通板性能良好，通板强度差30MPa左右；成形性能良好，d=0时冷弯测试全部合格；同时还具有良好焊接性能，焊接后，强度波动较小，均在母材部位断开；试制钢显微组织为珠光体和铁素体，晶粒均匀细小，平均尺寸为4～8／μm；实物质量满足集装箱和汽车制造行业要求，具有广阔市场前景。     

Investigation of Centreline Segregation and Centreline Porosity in CC ‐ Slabs

Improvements of solidification processing in conventional or near net shape casting depend on sophisticated methods of macroscopic examination of central unsoundness and inhomogeneity of the cast material. As long as remarkable deviations referring to the quality features exist between the slab centre and the bulk material such methods should be looked after. Two semi‐macroscopic methods of segregation analysis are discussed in this paper: firstly, the potential of the emission spectral analysis combined with sectioning of a sample and secondly, the computer aided micro‐probe analysis. Both methods are restricted to small local areas. The proneness of elements and steel grades with respect to micro‐ and macrosegregation as well as distribution‐ and segregation coefficients are determined. The effect of a diffusion anneal on homogenisation of segregation is studied. Last not least the precipitation of sulphides, phosphides or carbonitrides is estimated. Ultrasonic detection of the central unsoundness of conventional slabs or thin slabs is a new approach towards a quantitative macroscopic examination. The sample size is 400 mm x 300 mm x 30 mm. To achieve a low ultrasonic noise using a 5 MHz‐transducer the samples are heat treated for grain refinement. “Dog bone porosity”, macroscopic topographical misfit between the upper and lower solidifying shells, periodical corner cracks or systematic transverse centre cracks are detected. Obviously, segregations do not reflect the ultrasonic beam. However, it can be presumed that an interrelation exists between porosity and segregation, although these might be locally apart from each other. This new ultrasonic test of the central unsoundness of continuous cast (c.c.) slabs gives valuable arguments to machine builders and maintenance people to decide on the right concepts for strand guidance, support rollers and secondary cooling. Soft reduction can be optimized and variations in casting speed counteracted by dynamic means. R&D service of this kind can help steelmakers when decisions are impending to build new casting machines or revamp old ones.     

街面水电站混凝土面板堆石坝主要技术问题探讨

街面水电站拦河坝为混凝土面板堆石坝,在面板止水结构型式、面板防裂措施、上游面的施工方法、趾板开挖处理及趾板灌浆等方面,根据工程实际情况,结合国内外的新技术新工艺进行了探讨。