Numerical Investigation of the Capture of Polydisperse Particles by Charged Droplets

The capture of particles by charged droplets was simulated by considering the electrostatic interactions of droplet-droplet and droplet-particle. The results indicate that the electrostatic repulsion between droplets leads to a dynamic accumulation mode of particles. However, the droplet spacing has an insignificant effect on the capture efficiency when the electrostatic deposition predominates. The increase of droplet charge remarkably improves the capture efficiency, in which the capture of fine particles accounts for the largest proportion. Compared to the droplet charge, the droplet size shows a limited improvement in the capture efficiency. Reducing the droplet velocity prolongs the capture time instead of enhancing the capture capacity per unit time, thereby improving capture efficiency.     

Low cycle fatigue behavior of a eutectic 80Au/20Sn solder alloy

The eutectic 80Au/20Sn solder alloy is widely used in high power electronics and optoelectronics packaging. In this study, low cycle fatigue behavior of a eutectic 80Au/20Sn solder alloy is reported. The 80Au/20Sn solder shows a quasi-static fracture characteristic at high strain rates, and then gradually transforms from a transgranular fracture (dominated by fatigue damage) to intergranular fracture (dominated by creep damage) at low strain rates with increasing temperature. Coffin-Manson and Morrow models are proposed to evaluate the low cycle fatigue behavior of the 80Au/20Sn solder. Besides, the 80Au/20Sn solder has enhanced fatigue resistance compared to the 63Sn/37Pb solder.     

基于云概率密度分布估计的大坝监测数据分析

大坝运行监测易受自然环境和监测条件影响，存在时间和空间上的变异性，监测数据具有不确定性。以云理论的随机性和不确定性分析方法为基础，并与空间数据辐射思想相结合，建立了云滴概率密度分布估计模型，然后导出云概率密度分布函数，依据样本监测数据推求母体空间数据的分布特征，并设计了基于逆向云算法云变换的计算程序。分析陆浑水库1979~1999年测压管监测数据和位移变形数据的云概率密度分布特征和云数字特征，得出了20 a来大坝的数据分布特征和运行状态。监测数据分析结果表明，云概率密度分布估计不仅能有效合理地分析大坝的运行状态，而且能够依据云数字特征来判断监测状态和监测环境的异常变化。      

In situ measurements of human cough aerosol hygroscopicity

The airborne dynamics of respiratory droplets, and the transmission routes of pathogens embedded within them, are governed primarily by the diameter of the particles. These particles are composed of the fluid which lines the respiratory tract, and is primarily mucins and salts, which will interact with the atmosphere and evaporate to reach an equilibrium diameter. Measuring organic volume fraction (OVF) of cough aerosol has proved challenging due to large variability and low material volume produced after coughing. Here, the diametric hygroscopic growth factors (GF) of the cough aerosol produced by healthy participants were measured in situ using a rotating aerosol suspension chamber and a humidification tandem differential mobility analyser. Using hygroscopicity models, it was estimated that the average OVF in the evaporated cough aerosol was 0.88 ± 0.07 and the average GF at 90% relative humidity (RH) was 1.31 ± 0.03. To reach equilibrium in dry air the droplets will reduce in diameter by a factor of approximately 2.8 with an evaporation factor of 0.36 ± 0.05. Hysteresis was observed in cough aerosol at RH = ∼35% and RH = ∼65% for efflorescence and deliquescence, respectively, and may depend on the OVF. The same behaviour and GF were observed in nebulized bovine bronchoalveolar lavage fluid.     

Interfacial reactions in In-Sn/Ni couples and phase equilibria of the In-Sn-Ni system

The In-Sn-Ni alloys of various compositions were prepared and annealed at 160°C and 240°C. No ternary compounds were found; however, most of the binary compounds had extensive ternary solubility. There was a continuous solid solution between the Ni₃Sn phase and Ni₃In phase. The Sn-In/Ni couples, made of Sn-In alloys with various compositions, were reacted at 160°C and 240°C and formed only one compound for all the Sn-In alloys/Ni couples reacted up to 8 h. At 240°C, Ni₂₈In₇₂ phase formed in the couples made with pure indium, In-10at.%Sn and In-11at.%Sn alloys, while Ni₃Sn₄ phase formed in the couples made of alloys with compositions varied from pure Sn to In-12at.%Sn. At 160°C, except in the In/Ni couple, Ni₃Sn₄ formed by interfacial reaction.     

Two‐phase production of cyclohexene and cyclooctene oxides in water as an approach to pollution prevention

Liquid–liquid two‐phase epoxidation from cyclohexene and cyclooctene in aqueous potassium peroxymonosulfate (commercially available as Oxone^®) solution was studied as an application in pollution prevention. To avoid potential emissions of volatile organic compounds an aqueous solution was employed to replace the usual chlorinated solvents used in epoxide production. A droplet column reactor and stirred tank reactor were used to investigate two‐phase synthesis of epoxide. An aqueous Oxone^® solution was used to oxidize a dispersion of alkene droplets and form epoxide. The study of aqueous epoxidation in both reactors showed that the epoxidation of alkenes can be represented as a first order reaction with respect to alkene. The salting out effect of Oxone^® concentration was studied in both reactors and found to be very similar at optimal conditions. In comparing the two reactors, it was found that the droplet column reactor produces larger quantities of product per unit reactor volume for the same reaction time. The objective of this study is to provide an alternative reactor design and synthesis route that can meet pollution prevention goals. Copyright © 2004 Society of Chemical Industry     

Low-cycle fatigue properties of eutectic solders at high temperatures

This paper details the deformation mechanism and low‐cycle fatigue life of eutectic solder alloys at high temperature (around 0.8T_m). Grain boundary sliding generally nucleates a wedge‐type cavity that reduces the low‐cycle fatigue life of metals. In this study, grain boundary sliding has promoted intergranular failure contributing to the reduction in fatigue life of Sn–Ag–Cu alloy. However, grain boundary sliding has exerted no deleterious effects on fatigue resistance of eutectic Pb–Sn and Bi–Sn alloys. The phase boundary sliding with very fine microstructure induces exceptional ductility in these alloys leading to superior low‐cycle fatigue endurance for theses eutectic Pb–Sn and Bi–Sn alloys.     

Effect of strain waveform on creep-fatigue life for Sn–8Zn–3Bi solder

This paper describes the creep‐fatigue life of Sn–8Zn–3Bi under push–pull loading. Creep‐fatigue tests were carried out using Sn–8Zn–3Bi specimens in fast–fast, fast–slow, slow–fast, slow–slow and hold–time strain waveforms. Creep‐fatigue lives in the slow–slow and hold‐time waveforms showed a small reduction from the fast–fast lives but those in the slow–fast and fast–slow waveforms showed a significant reduction from the fast–fast lives. Conventional creep‐fatigue life prediction methods were applied to the experimental data and the applicability of the methods was discussed. Creep‐fatigue characteristics of Sn–8Zn–3Bi were compared with those of Sn–3.5Ag and Sn–37Pb.     

印制板液态感光阻焊油墨的工艺控制

本文介绍印制板液态感光阻焊油墨的工艺流程、工艺控制，并对生产中较常出现的几种质量问题进行讨论，进而提出解决措施。     

一种制备磁性粉末的新技术--均匀颗粒成型法

采用均匀颗粒成型法（Uniform Dropler Spray-UDS）制备Fe基合金粉末，该方法制备的颗粒粒度分布均匀，性能一致，大大优于传统的粉末制备方法（如破碎法、气雾化），具有广阔的应用前景。本文分析了粉末制备过程中颗粒尺寸的影响因素，结果表明：颗粒的大小主要取决于坩埚底部小孔、坩埚内外气体压强差以及振荡频率三个独立变量。