Low cycle fatigue behavior of a eutectic 80Au/20Sn solder alloy

The eutectic 80Au/20Sn solder alloy is widely used in high power electronics and optoelectronics packaging. In this study, low cycle fatigue behavior of a eutectic 80Au/20Sn solder alloy is reported. The 80Au/20Sn solder shows a quasi-static fracture characteristic at high strain rates, and then gradually transforms from a transgranular fracture (dominated by fatigue damage) to intergranular fracture (dominated by creep damage) at low strain rates with increasing temperature. Coffin-Manson and Morrow models are proposed to evaluate the low cycle fatigue behavior of the 80Au/20Sn solder. Besides, the 80Au/20Sn solder has enhanced fatigue resistance compared to the 63Sn/37Pb solder.     

Defocusing image to pattern contact holes using attenuated phase shift masks

The patterning of contact holes by selecting out-of-focus image plane (defocus) using attenuated phase shift masks (APSM) has been studied. Defocus is found to enhance the image modulation at low partial coherence for contact holes with negative local average of mask function. Semi-dense holes up to 130 nm in 8% APSM have been printed by 0.5 μm defocus at a partial coherence of 0.31 using KrF scanner with highest numerical aperture of 0.68. However, these holes were closed with in-focus imaging. Defocus is also found to be beneficial for patterning the pitches that have extensive side lobes with in-focus imaging.     

X射线光刻掩模背面刻蚀过程中的形变仿真

开发了理论模型以验证有限元方法用于X射线光刻掩模刻蚀过程数值仿真的正确性。利用相同的有限元技术，对X射线光刻掩模的背面开窗、Si片刻蚀过程进行数值仿真。结果表明，图形区域的最大平面内形变(IPD)出现在上、下边缘处，最大非平面形变(OPD)出现在左、右边缘处。此外对Si片单载荷步刻蚀和多载荷步刻蚀的仿真进行比较，结果表明图形区域最终的形变量与Si片刻蚀的过程无关。     

数字电视用中分辨率74cm纯平彩色显像管BC配列不良的分析与对策

通过对74cm中分辨率纯平彩色显像管BC配列局部严重群散不良的调查分析,确定荫罩受力塌陷是主要原因,通过改良设计、工艺优化及其它方面的综合对策,使以上技术难题得到满意的解决,整管不良率由4.78%下降到0.172%。     

Interfacial reactions in In-Sn/Ni couples and phase equilibria of the In-Sn-Ni system

The In-Sn-Ni alloys of various compositions were prepared and annealed at 160°C and 240°C. No ternary compounds were found; however, most of the binary compounds had extensive ternary solubility. There was a continuous solid solution between the Ni₃Sn phase and Ni₃In phase. The Sn-In/Ni couples, made of Sn-In alloys with various compositions, were reacted at 160°C and 240°C and formed only one compound for all the Sn-In alloys/Ni couples reacted up to 8 h. At 240°C, Ni₂₈In₇₂ phase formed in the couples made with pure indium, In-10at.%Sn and In-11at.%Sn alloys, while Ni₃Sn₄ phase formed in the couples made of alloys with compositions varied from pure Sn to In-12at.%Sn. At 160°C, except in the In/Ni couple, Ni₃Sn₄ formed by interfacial reaction.     

Low-cycle fatigue properties of eutectic solders at high temperatures

This paper details the deformation mechanism and low‐cycle fatigue life of eutectic solder alloys at high temperature (around 0.8T_m). Grain boundary sliding generally nucleates a wedge‐type cavity that reduces the low‐cycle fatigue life of metals. In this study, grain boundary sliding has promoted intergranular failure contributing to the reduction in fatigue life of Sn–Ag–Cu alloy. However, grain boundary sliding has exerted no deleterious effects on fatigue resistance of eutectic Pb–Sn and Bi–Sn alloys. The phase boundary sliding with very fine microstructure induces exceptional ductility in these alloys leading to superior low‐cycle fatigue endurance for theses eutectic Pb–Sn and Bi–Sn alloys.     

Effect of strain waveform on creep-fatigue life for Sn–8Zn–3Bi solder

This paper describes the creep‐fatigue life of Sn–8Zn–3Bi under push–pull loading. Creep‐fatigue tests were carried out using Sn–8Zn–3Bi specimens in fast–fast, fast–slow, slow–fast, slow–slow and hold–time strain waveforms. Creep‐fatigue lives in the slow–slow and hold‐time waveforms showed a small reduction from the fast–fast lives but those in the slow–fast and fast–slow waveforms showed a significant reduction from the fast–fast lives. Conventional creep‐fatigue life prediction methods were applied to the experimental data and the applicability of the methods was discussed. Creep‐fatigue characteristics of Sn–8Zn–3Bi were compared with those of Sn–3.5Ag and Sn–37Pb.     

晶体管的计算机辅助设计

将晶体管设计中繁琐的纵向、横向参数的设计计算以及参数验算,采用Basic人机对话方式,由计算机完成。并用BAsic语言绘制出所需的七块光刻掩膜图。既大大地减轻了设计人员繁琐劳动、缩短了设计时间、提高设计质量,又便于修改。还可广泛用于同种结构的不同动率要求的各种晶体管的设计中。     

印制板液态感光阻焊油墨的工艺控制

本文介绍印制板液态感光阻焊油墨的工艺流程、工艺控制，并对生产中较常出现的几种质量问题进行讨论，进而提出解决措施。     

Effect of Cu concentration on the reactions between Sn-Ag-Cu solders and Ni

The reaction between the Sn-Ag-Cu solders and Ni at 250°C for 10 min and 25 h was studied. Nine different Sn-Ag-Cu solders, with the Ag concentration fixed at 3.9 wt.% and Cu concentrations varied between 0.0–3.0 wt.%, were used. When the reaction time was 10 min, the reactions strongly depended on the Cu concentration. At low-Cu concentrations (≦0.2 wt.%), only a continuous (Ni_1−xCu_x)₃Sn₄ layer formed at the interface. When the Cu concentration increased to 0.4 wt.%, a continuous (Ni_1−xCu_x)₃Sn₄ layer and a small amount of discontinuous (Cu_1−yNi_y)₆Sn₅ particles formed at the interface. When the Cu concentration increased to 0.5 wt.%, the amount of (Cu_1−yNi_y)₆Sn₅ increased and (Cu_1−yNi₆)₆Sn₅ became a continuous layer. Beneath this (Cu_1−yNi_y)₆Sn₅ layer was a very thin but continuous layer of (Ni_1−xCu_x)₃Sn₄. At higher Cu concentrations (0.6–3.0 wt.%), (Ni_1−xCu_x)₃Sn₄ disappeared, and only (Cu_1−yNi_y)₆Sn₅ was present. The reactions at 25 h also depended strongly on the Cu concentration, proving that the strong concentration dependence was not a transient phenomenon limited to a short reaction time. The findings of this study were rationalized using the Cu-Ni-Sn isotherm. This study shows that precise control over the Cu concentration in solders is needed to produce consistent results.