Structural study of degraded ZnMgSSe blue light emitters

Using electroluminescence (EL) topography and transmission electron microscopy (TEM), we investigated the nonluminescent regions which form while current is being injected into ZnMgSSe/ZnSSe/ZnCdSe-based blue light emitters. Small dark spots were observed just after turn-on and spread out forming rough nonluminescent triangles in the <100> directions in the EL image of the active region. TEM studies showed that the small dark spots are pre-existing stacking faults originating at the substrate/epitaxial layer interface. The nonluminescent triangles were found to be a dense region of dislocation dipoles and dislocation loops. Each dipole was aligned along two <110> directions in the {111} planes. The Burgers vectors were of the type a/2<011> inclined at 45° to the (001) junction plane.     

The importance of the compression test procedure for plastic drums for dangerous goods

Packagings for the transport of dangerous goods are tested by four tests:- free fall, leakproofness, hydraulic pressure and stacking. However, the test procedures can be interpreted in different ways, particularly the stacking test. Some test authorities apply a guided load to the top of the package and others, including the LNE in France, use non-guided loads. The objective of recent research carried out at LNE was to evaluate the risk (in terms of stack stability for dangerous goods packagings) if the stacking tests are performed with guided loads rather than non-guided loads. The stacking tests were carried out on a limited number of plastic drums (200 of four types) submitted for qualification testing using the above four tests, with either guided or non-guided loads. From the results we conclude that:

• i for the transport of dangerous goods of Danger Group I, the field of use is not altered when tested by either procedure.
• ii with goods of Danger Groups II and III, the use of either procedure does not alter the position as far as transport is concerned. However, there is a risk in warehousing: the non-guided procedure being preferred.

     

Crystalline complex between poly(γ-methyl l-glutamate) and dimethyl phthalate

The crystalline complex between poly(γ-methyl l-glutamate) (PMLG) and dimethyl phthalate (DMP) has been formed in films cast from a solution in dichloroethane. It has the stoichiometry of 1 mol of DMP to three or four residues of PMLG and shows two definite characteristics in X-ray diffraction patterns; one is the large hexagonal unit cell with the edge of around 28 Å and another the ‘extra’ 5.07 Å meridional reflection which can not be interpreted by a PMLG α-helical conformation. The structural examination for the films with various DMP contents is carried out by X-ray, viscoelastic, and d.s.c. measurements and the following structure is proposed for the crystalline complex. Four PMLG are associated to form a group which is hexagonally packed and DMP molecules, located in the gaps between groups, form a specific favourable helical structure along PMLG chains in which the van der Waals stacking of benzene rings of DMP is significant.     

复合材料船用螺旋桨设计与CFD/FEM计算

将基于RANS方程的计算流体力学方法与有限元方法相结合,沿着螺旋桨水动力性能计算、复合材料螺旋桨建模及结构铺层设计、CFD/FEM载荷传递、复合材料螺旋桨结构力学性能计算,水动力性能收敛判定的设计分析流程,完成了某种螺旋桨桨叶的初步的设计过程.提出一种预变形策略以改进复合材料螺旋桨的综合性能.计算结果表明,该复合材料螺旋桨能够满足预定设计指标的要求,在达到传统金属螺旋桨水动力性能要求的同时,减重30%,运行效率增加.研究结果充分说明了所采用设计方法的可行性.     

TiNb（Y_2O_3）长纤维增强Ti－48Al－2Cr－2Nb合金复合材料的弯曲变形与界面

研究了ＴｉＮｂ（Ｙ２Ｏ３）连续纤维增强Ｔｉ－４８Ａｌ－２Ｇｒ－２Ｎｂ合金复合材料的界面及显微组织。研究发现：复合材料的弯曲强度比基体略有提高，弹性模量和挠度有所下降。在纤维和基体之间形成一层约１０～２０μｍ厚的α２－Ｔｉ３Ａｌ性层，近界面基体组织有片层化倾向。大量变形层错带和孪晶出现及界面位错墙的形成成为塑变及强化的主要机制。     

铝电解槽大修渣场污染防范措施

针对铝电解槽大修渣淋溶液具有毒性 ,处理不慎将污染地下水环境的情况 ,以遵义电解铝厂的电解渣场设计为例 ,指出只要对电解渣场做好防渗处理 ,即可解决电解渣淋溶液对地下水环境的污染问题。     

Cu—Zn—Al合金贝氏体的初生态及三维台阶

利用透射电镜研究了Cu—25.9Zn—3.75Al(wt-%)合金的贝氏体相变机制结果表明,贝氏体α_1在形成初期内部没有层错,早期典型形态为一侧比较平直,另一侧则存在三维巨型台阶,台阶宽面与贝氏体惯习面平行,其高度和间距分别约为10—40和50—230nm,台阶是可动的,贝氏体通过台阶的移动而增厚     

L12型Al3Ti合金室温变形超位错的分解及计算机图像模拟

利用透射电子显微镜和计算机图像模拟技术研究了ＬＩ２型Ａｌ３Ｔｉ合金室温变形的位错核心结构，结果表明：α（１１０）超位错在｛１１１｝面上分解成两个α／３｛１１２｝型超偏位错，其间为超点阵内禀层错。     

30万吨横切生产线堆垛机控制程序优化

随着钢材市场的竞争日趋激烈,对产品质量的要求越来越高,首钢京唐热轧板厂横切30万吨生产线堆垛机的控制精度已不能满足目前的质量要求。为此对其自动化控制程序进行了优化、打包。经过自动控制程序的优化后,横切机组堆垛机自动控制程序及堆垛机运行正常,设备冲击缺陷和产品缺陷同时得到了控制,在提高生产率和产品质量的同时,获得了良好的经济效益。