Waveguide external cavity narrow linewidth semiconductor lasers

Narrow linewidth light source is a prerequisite for high-performance coherent optical communication and sensing.Waveguide-based external cavity narrow linewidth semiconductor lasers(WEC-NLSLs)have become a competitive and attractive candidate for many coherent applications due to their small size,volume,low energy consumption,low cost and the ability to integrate with other optical components.In this paper,we present an overview of WEC-NLSLs from their required technologies to the state-of-the-art progress.Moreover,we highlight the common problems occurring to current WEC-NLSLs and show the possible approaches to resolving the issues.Finally,we present the possible development directions for the next phase and hope this review will be beneficial to the advancements of WEC-NLSLs.     

定距螺旋桨对船用主机外特性的要求分析

为解决定距螺旋桨与船用主机在船舶运行工况的机桨匹配问题,结合船舶系泊和航行试验的相关标准,分析和归纳船舶运行数据,将实船测试与船机桨匹配理论计算相结合,得出运输船和拖轮在常用工况及特殊工况下定距螺旋桨对主机外特性的定量要求,为配套不同细分市场时船用主机的优化和开发提供参考依据。     

大直径平底负压容器优化设计

通过对大直径平底负压容器平底板的设计计算,平底板计算厚度很厚。通过分析,提出了对平底板采取加强措施,从而减薄平底板计算厚度的方法。该容器在实际生产过程中性能可靠、稳定,对类似设备设计具有借鉴意义。     

光照水电站装设筒形阀分析

筒形阀是一种新型的水轮机进水阀,它与球阀或蝴蝶阀相比较有防止机组飞逸事故扩大效果明显、减轻导叶全关时导水机构的快速破坏并减少漏水量,以及动水开启方便、所需时间短等优点,但对运行条件也有一定的要求。光照水电站是贵州省第1个拟采用筒形阀的电站,为此对装设筒形阀的可行性和必要性进行了认真的分析。     

移动通信系统中功率控制研究

在阐述功率控制在移动通信系统中的发展过程的基础上，着重研究了WCDMA系统的功率控制，最后对功率控制未来的研究方向做了简要的分析。     

双缸式气动-手动楔式闸阀在柴油罐上的应用

文章简单介绍了气动阀的结构、工作原理及特点,并时堆修保养注意事项以及可能发生的故障和排除故障的方法做了详细讲解。最后,将气动阀在柴油罐上的应用情况与普通闸阀相比较,分析其使用性能和优点,进一步推广气动闽在锦西石化分公司的应用。     

国产风机盘管空调系统常见问题分析

分析了国产风机盘管使用中常见的问题,指出机组因风量不足、冷量风量匹配不合理以及风机盘管某些设备故障,导致了风机盘管精度低、舒适性差、能耗高等一系列问题。指出应引起空调设计和运行维护人员的注意。     

THE STATISTICAL DISTRIBUTION OF EXTREME VALUES OF WAVE-CURRENT FORCES ACTING ON SLENDER CIRCULAR CYLINDER IN IRREGULAR WAVES

Based on model test,the statistical distribution of extreme values of wave-current in-line forces acting on vertical circular cylinder is analyzed in this paper.It is shownthat the results calculated by the simplified method,proposed by authors,agree well with the testdata;Weibull distribution is also adoptable in the region of high KC number, and the shapeparameter a and scale parameter β are related well with KC number respectively.     

A new monitoring system for piping systems in fossil fired power plants

A CEC-funded project has been performed to tackle the problem of producing an advanced Life Monitoring System (LMS) which would calculate the creep and fatigue damage experienced by high temperature pipework components. Four areas were identified where existing Life Monitoring System technology could be improved:

1. 1. the inclusion of creep relaxation

2. 2. the inclusion of external loads on components

3. 3. a more accurate method of calculating thermal stresses due to temperature transients

4. 4. the inclusion of high cycle fatigue terms.

The creep relaxation problem was solved using stress reduction factors in an analytical in-elastic stress calculation. The stress reduction factors were produced for a number of common geometries and materials by means of non-linear finite element analysis. External loads were catered for by producing influence coefficients from in-elastic analysis of the particular piping system and using them to calculate bending moments at critical positions on the pipework from load and displacement measurements made at the convenient points at the pipework. The thermal stress problem was solved by producing a completely new solution based on Green's Function and Fast Fourier transforms. This allowed the thermal stress in a complex component to be calculated from simple non-intrusive thermocouple measurements made on the outside of the component. The high-cycle fatigue problem was dealt with precalculating the fatigue damage associated with standard transients and adding this damage to cumulative total when a transient occurred.

The site testing provided good practical experience and showed up problems which would not otherwise have been detected.     

三角旋转活塞发动机缸体型线研究

根据三角旋转活塞发动机运动几何原理 ,详细分析了缸体型线。缸体的实际型线是双弧外摆线的等距曲线 ,并由此导出其数学表达式。本文进一步说明了两种几何运动实现方式 ,分析了参数的几何意义 ,并给出其表达式。