锥形阀压电薄膜泵的初步研究

提出一种适应高频工作状态的压电薄膜泵结构，实步分析了所采用的锥形阀的工作原理与作用，设计了试验泵结构，加工了样机，通过试验证明了锥形阀的有效性，为进一步的研究打下了基础。     

圆锥孔径测量方法与误差分析

圆锥孔径的测量往往比较困难、且精度较低。提出长度测量仪器与环规配合使用,应 用比较测量的方法检测圆锥孔的直径。通过计算和分析可以得出,当被测圆锥孔径不大于180 mm 时,其测量不确定度可小于1.84 μm。给出了测量方法和不确定度计算公式供操作时参考。     

锅盖落料拉伸冲孔切边复合模设计

分析了不锈钢锅盖成形工艺，确定了用一副复合模完成落料、浅球形的正向拉伸和低锥形的反向拉伸、冲孔和切边的工序过程。同时也阐述了复合模工作过程及注意事项。     

大变形零件温挤压凹模型孔设计技巧

对大变形程度、圆坯正挤压出两种变截面挤压方式进行了工艺和质量对比，在凹模型孔形式上采用了双锥角模口导流方式，第一次提出了在挤压初始阶段，利用双锥角形成大的材料初始流速和流动惯性来克服流动前期变形抗力峰值以达到模口材料周边匀速流动目的的理论。     

高速线材轧机锥套故障分析与改进

高速线材生产线精轧机、预精轧机使用的锥套，在材质、结构、处理工艺及生产操作上存在诸多不当之处，为此进行了多项改进，使锥套故障彻底排除，使用寿命达3～5月，而价格仅为进口件的1／3。     

锥形凹模多层拉伸模设计

介绍了锥形拉伸凹模的结构及参数 ,其中重点介绍了多层拉伸模的结构及设计特点。此结构定位精度高 ,操作方便 ,生产效率高     

锥形凹模板料不起皱条件和极限拉深系数

本文通过分析锥形凹模拉深变形过程，利用试验数据，列出了板料不起皱的条件；并运用主应力法和板料弯曲的外力功等于内力功的原理以及摩擦理论，推导出加工硬化时变形区危险断面最大拉应力计算公式和无压边装置锥形凹模的圆筒件极限拉深系数计算公式；均由实例进行验证。拉深系数为０．３９的两种零件，从试制到生产，证明了锥形凹模是可以实现深拉深的模具。     

Modulation of viewing angle on an LCD surface through backlight optics

Abstract— A backlight unit (BLU) that varies the viewing angle from the top to the bottom surface of a transmissive LCD screen has been developed through the design and fabrication of microstructures on a light‐guide plate (LGP). An array of taper prisms has been designed and fabricated on the back surface of the LGP, which resulted in the variation of 29° in the angular distribution of the luminance of the backlight from the top sector to the bottom sector of its surface. This characteristic is employed to modulate the viewing angle of the LCD from the top of the screen to the bottom of the screen for special applications.     

圆锥螺纹塞规基面中径的测量

介绍了一种圆锥螺纹塞规基面上中径的测量方法.应用量针和万能测长仪测得距基面一定截面上的中径d2,然后在万能工具显微镜上测得此截面距离基面的距离,以此求得基面上的中径d基.     

Discussion on the problems related to NC machining of toroid-shaped taper cutter with constant angle between cutting edge and the cutter axis

Defining the helical angle as the angle between the cutting edge and revolving axis of the cutter presents the designing models of the cutting edge and helical groove of a toroid shaped taper cutter. Under the condition of a certain revolving speed, the relative radial and axial feeding speeds of the grinding wheel in two-axis NC machining of the cutter are deduced. The models for calculating the actual obtained groove and the simulation-method of computer are also provided.The surface near to the top of the end cutter has no helical cutting edges and infinite feeding speeds of NC machine. It is necessary to adopt a supplementary cutting edge. A supplementary cutting edge is designed as a cutting edge with a constant pitch. This paper provides valuable reference for the design and NC machining of this kind of toroid shaped taper cutter.