磨料有序排布电镀砂轮的制备及其把持力研究

为解决电镀砂轮磨削加工中容屑空间不足的问题，采用点胶微粘接的方法制备了磨料有序排布的电镀砂轮，分析了磨料粘接效果和镀层力学性能。通过SEM分析了磨料/镀层/导电胶的结合界面，并进行了干磨削试验。研究结果表明，直径约为磨料粒径40%的胶点可粘接住磨料，单个胶点上粘接多颗磨料的占比小于6%；双脉冲电镀工艺制备的镀层显微硬度大于500HV，表层残余应力小于100MPa，磨料/镀层/导电胶之间的界面贴合紧密，无明显缺陷；砂轮在磨削时没有出现磨料脱落现象。     

Study on the non-uniform contact during ELID groove grinding

This paper introduces the potential feasibility that ELID (electrolytic in-process dressing) grinding replaces superfinishing in bearing manufacturing, but ELID grinding will bring new challenges. Different regions present distinguish surface profile due to the non-uniform contact in ELID groove grinding. However, few reports explaining the non-uniform contact are available. This article explores the mechanisms of the non-uniform contact during ELID groove grinding. Experiments on the non-uniform contact between bearing raceway and grinding wheel have been carried out under different conditions. The results show that non-uniform contact exists in ELID groove grinding process and it exerts influence on the profile of the raceway surface. Non-uniform contact influences the Rsk and Rku value all the time, but it influences the Ra value occasionally. Improvement strategies of eliminating the non-uniform contact are also discussed based on the experimental study.     

M1080B无心外圆磨床改进

M1080B无心外圆磨床砂轮及导轮宽度较窄,磨削轴承套圈外圆时,磨削效率低,托板架调整较为繁琐、皮带打滑、磨损较为严重。针对上述问题,提出了相应的解决办法,提高了磨削效率。     

埋地管道泄漏内封堵装置设计与研究

针对流体输送埋地管道泄漏问题,设计了一种利用管道机器人携带封堵气囊进行快速应急封堵修复的埋地管道泄漏内封堵装置。采用矩阵变换方法建立了牵引系统驱动轮过弯方程,利用MATLAB软件对过弯方程进行了验证,同时利用ADAMS软件仿真分析过弯路径与驱动轮转角对牵引系统行走速度的影响。研究结果表明:由两个串联封堵器组成的应急封堵系统可满足复杂工况下的管道泄漏封堵要求;牵引系统驱动轮在弯管内部行走时,单轮速度呈周期性变化,但三个驱动轮整体周期运动特性一致;驱动轮转角在25°~40°时,牵引系统行走速度与驱动轮转角成正比,且转角为30°时驱动效果最好。该内封堵装置的结构设计可为管道泄漏应急封堵领域装备的研发提供重要参考。     

Effect of grinding-induced cyclic heating on the hardened layer generation in the plunge grinding of a cylindrical component

This paper discusses the effects of the grinding-induced cyclic heating on the properties of the hardened layer in a plunge cylindrical grinding process on the high strength steel EN26. It was found that a multi-pass grinding brings about a uniform and continuous hardened layer along the circumference of the cylindrical workpiece. An increase of the number of grinding passes, leads to a thicker layer of hardening, a larger compressive residual stress and a deeper plastic deformation zone. Within the plastic deformation zone, the martensitic grains are refined by the thermo-mechanical loading, giving rise to a hardness of 12.5% higher than that from a conventional martensitic transformation. The coupled effects of heat accumulation and wheel wear in the multi-pass grinding are the main causes for the thickening of the hardened layer. A too small infeed per workpiece revolution would result in insufficient grinding heat, and in turn, bring about an undesirable tempered hardened layer and a reduction of its hardness.     

Simulation of Strength Distribution in Ground Ceramics by Incorporating Residual Stress Effect

Strength of ground ceramics may be affected by residual stress as well as surface flaws induced by grinding. Strength prediction for ground ceramics is convenient for mechanical design of ceramic components. In this article, a numerical procedure based on fracture mechanics was proposed to estimate strength distribution of ground ceramics by considering grinding-induced residual stress. Bending strength and residual stress of ground ceramics were measured for three grinding-conditions. By comparison of simulated results with experimental ones, it was revealed that strength characteristics in experiments were well simulated by using the proposed procedure.     

铁路桥梁横向振动模拟及适应快速行车结构型式的研究

针对铁路提速后出现的上承式简支钢板梁桥跨中横向振幅过大的问题,以羊楼司桥(L=32m单跨上承式简支钢板梁桥)为例进行实桥检测和数值模拟,建立车辆、线路、桥梁三者的联合模型,考虑轮轨接触力,应用MSC/DYTRAN大型结构分析程序进行车线桥动力相互作用的仿真分析。研究揭示我国用量最多的C62型货车以70∽80km/h的速度空载通过时,该跨度的钢板梁桥发生横向谐振的机理。此外,用该方法对32m跨长的组合梁结构进行桥梁动力特性及列车走行性分析,表明该结构满足提速货车和高速电动旅客列车走行的要求。研究结果对我国高速铁路桥梁建设和既有桥梁的改造具有积极意义。     

Frequency weighting for the evaluation of steering wheel rotational vibration

The human perception of rotational hand–arm vibration has been investigated by means of a test rig consisting of a rigid frame, an electrodynamic shaker unit, a rigid steering wheel, a shaft assembly, bearings and an automobile seat. Fifteen subjects were tested while seated in a driving posture. Four equal sensation tests and one annoyance threshold test were performed using sinusoidal excitation at 18 frequencies in the range from 3 to 315 Hz. In order to guarantee the generality of the equal sensation data, the four tests were defined to permit checks of the possible influence of three factors: reference signal amplitude, psychophysical test procedure and temporary threshold shift caused by the test exposure. All equal sensation tests used a reference sinusoid of 63 Hz at either 1.0 or 1.5 m/s² r.m.s. in amplitude. The four equal sensation curves were similar in shape and suggested a decrease in human sensitivity to hand–arm rotational vibration with increasing frequency. The slopes of the equal sensation curves changed at transition points of approximately 6.3 and 63 Hz. A frequency weighting, called W_s, was developed for the purpose of evaluating steering wheel rotational vibration. The proposed W_s has a slope of 0 dB per octave over the frequency range from 3 to 6.3 Hz, a slope of −6 dB per octave from 6.3 to 50 Hz, a slope of 0 dB per octave from 50 to 160 Hz and a slope of −10 dB per octave from 160 to 315 Hz. W_s provides a possible alternative to the existing W_h frequency weighting defined in International Standards Organisation 5349-1 (2001) and British Standards Institution BS 6842 (1987).

Relevance to industry

For the manufacturers of tyres, steering systems and other vehicular components the proposed W_s frequency weighting provides a more accurate representation of human perception of steering wheel rotational vibration than the W_h weighting of ISO 5349-1 and BS6842.     

成形磨削中砂轮修整精度的研究

成形磨削一般采用金刚石笔来修整所需要的砂轮形状，金刚石笔在安装中的位置误差将影响被加工工件的精度，本文对此误差的大小进行了分析。     

在线磨辊辊面粗糙度的实验研究

影响轧辊表面粗糙度的因素很多，为此对影响辊面粗糙度的因素进行了系统分析和实验研究，得出了轧辊和砂轮的速度、砂轮粒度、砂轮直径及磨削液等主要因素对轧辊表面粗糙度影响的一般规律。利用回归分析的方法建立了轧辊表面粗糙度的数学模型，并将计算值与实测值进行了比较，发现两者基本一致。此项研究为适时控制冷轧带钢在线磨辊辊面粗糙度提供了计算模型。