Fast handoff with reducing waste rate approach for wireless resources management in UMTS mobile networks

3G Wideband CDMA systems adopt the Orthogonal Variable Spreading Factor code tree as the channelization codes management for achieving high data rate transmission in personal multimedia communications. It assigns a single channelization code for each accepted connection. Nevertheless, it wastes the system capacity when the required rate is not powers of two of the basic rate. One good solution is to assign multiple codes for each accepted connection but it causes two inevitable drawbacks: long handoff delay and new call setup delay due to high complexity of processing with multiple channelization codes, and high cost of using more number of rake combiners. Especially, long handoff delay may result in more call dropping probability and higher Grade of Service, which will degrade significantly the utilization and revenue of the 3G cellular systems. Therefore, we propose herein an adaptive efficient codes determination algorithm based on the Markov Decision Process analysis approach to reduce the waste rate and reassignments significantly while providing fast handoff. Numerical results demonstrate that the proposed approach yields several advantages, including the lowest GOS, the least waste rate, and the least number of reassignments. Meanwhile, the optimal number of rake combiners is also analyzed in this paper. This research was supported in part by the National Science Council of Taiwan, ROC, under contract NSC-93-2213-E-324-018.     

国产风机盘管空调系统常见问题分析

分析了国产风机盘管使用中常见的问题,指出机组因风量不足、冷量风量匹配不合理以及风机盘管某些设备故障,导致了风机盘管精度低、舒适性差、能耗高等一系列问题。指出应引起空调设计和运行维护人员的注意。     

快速纳秒响应二代近贴聚焦像增强器的批量生产

叙述了二代近贴聚焦像增强器批量生产所用真空设备性能及特点，同时给出了管子工艺考核结果及管子纳秒时间响应特性。工艺考核结果表明，制管工艺可靠、性能稳定，管子批量生产合格率大于70％。     

Cs-K混合蒸气中Cs(8D)+K(4S)碰撞能量转移

在Cs-K混合蒸气中，两步激发Cs原子到8D态，观察了Cs(8D) K(4S)→Cs(5D) K(4P)碰撞能量合并逆过程(REP，reverse energy pooling)。应用双调制技术探测K(4P)原子发射的荧光，基态K原子密度用光学吸收方法测量。得到了REP速率系数，讨论了其它过程对速率系数的影响．     

Chemische Zusammensetzung und Mikrostruktur polymerabgeleiteter Gläser und Keramiken im System Si–C–O. Teil 2: Charakterisierung der Gefügeausbildung mittels hochauflösender Durchstrahlungselektronenmikroskopie und Feinbereichsbeugung

Chemical Composition and Microstructure of Polymer‐Derived Glasses and Ceramics in the Si–C–O System. Part 2: Characterization of microstructure formation by means of high‐resolution transmission electron microscopy and selected area diffraction Liquid or solid silicone resins represent the economically most interesting class of organic precursors for the pyrolytic production of glass and ceramics materials on silicon basis. As dense, dimensionally stable components can be cost‐effectively achieved by admixing reactive filler powders, chemical composition and microstructure development of the polymer‐derived residues must be exactly known during thermal decomposition. Thus, in the present work, glasses and ceramics produced by pyrolysis of the model precursor polymethylsiloxane at temperatures from 525 to 1550 °C are investigated. In part 1, by means of analytical electron microscopy, the bonding state of silicon was determined on a nanometre scale and the phase separation of the metastable Si–C–O matrix into SiO₂, C and SiC was proved. The in‐situ crystallization could be considerably accelerated by adding fine‐grained powder of inert fillers, such as Al₂O₃ or SiC, which permits effective process control. In part 2, the microstructure is characterized by high‐resolution transmission electron microscopy and selected area diffraction. Turbostratic carbon and cubic β‐SiC precipitate as crystallization products. Theses phases are embedded in an amorphous matrix. Inert fillers reduce the crystallization temperature by several hundred °C. In this case, the polymer‐derived Si–C–O material acts as a binding agent between the powder particles. Reaction layer formation does not occur. On the investigated pyrolysis conditions, no crystallization of SiO₂ was observed.     

回热损失对磁斯特林制冷循环制冷率的影响

从铁磁质的磁化强度一般表示式出发，探讨热阻和回热损失对磁斯特林制冷循环性能的影响，导出最大制冷率及其它性能参数。得到了结果适用于以顺磁质为工质的磁斯特林制冷循环。并指出在理想回热条件下的结论也适用于磁卡诺制冷循环。     

NMOS器件两次沟道注入杂质分布和阈电压计算

分别考虑了深浅两次沟道区注入杂质在氧化扩散过程中对表面浓度的贡献。对两次注入杂质的扩散分别提取了扩散系数的氧化增强系数、氧化衰减系数和有效杂地系数，给出了表面浓度与工艺参数之间的模拟关系式，以峰值浓度为强反型条件计算了开启电压，文章还给出了开启电压、氧化条件、不同注入组合之间的关系式。     

涡轮钻具在高陡构造的应用及展望

介绍了涡轮钻具在秋参1井的应用情况,详细叙述了涡轮钻具在山前高陡构造快速钻进及防斜打直方面的优点,与常规钻井相比,机械钻速明显提高,钻井周期明显缩短,钻井成本明显下降,经济效益显著。     

国产延迟树脂在腈纶溶剂NaSCN除杂装置的应用

叙述了国产的延迟树脂与进口DOWEX-11-A8树脂在腈纶厂NaSCN回收模拟装置上的比较试验,由试验数据可得出;国产的延迟树脂NVI脱除率性能略优于美国DOWEX-11-A8树脂,并可替代DOWEX-11-A8树脂应用于腈纶厂延迟装置中。     

提高自蔓延高温合成陶瓷内衬钢管性能的研究

在概括了自蔓延高温合成陶瓷内衬钢管的制备原理基础上，从降低陶瓷层孔隙率，减少陶瓷层裂纹和提高陶瓷层结合强度等方面，论述了提高自蔓延高温合成陶瓷内衬钢管性能的措施，对自蔓延高温合成陶瓷内衬钢管的应用现状及展望进行了评述。