Localized corrosion of (lean) duplex stainless steels in immersion units of urban wastewater treatment plants

With lower alloying cost and higher mechanical properties, lean duplex stainless steels can be an alternative to the more commonly used austenitic stainless steels. However, these alloys are still not the preferred choice, probably due to a lack of field experience. A study was thus initiated in view of defining the limits of use of selected (lean) duplexes for urban wastewater treatment units. The present paper shows the localized corrosion performance of selected lean duplexes in chloride contaminated solutions. The results are compared with austenitic S30403 and S31603 and with the more standard duplexes S82441 and S32205. The effect of welding was also investigated. Exposures in field municipal wastewater plants were conducted for 1 year in low and high chloride content units. The results show that lean duplexes S32101 and S32202 can be used as alternatives to S30403 and S31603 in low chloride electrolytes. At 500 ppm of chloride content, duplex stainless steel S32304 showed better corrosion resistance than S30403 and S31603. For higher chloride contents (1000 ppm and above) the standard duplexes S82441 and S32205 shall be preferred.     

A review on ultrasonic spot welding of copper alloys

As a solid state joining process, ultrasonic spot welding has been proven to be a promising technique for joining copper alloys. However, challenges still remain in employing ultrasonic spot welding to join copper alloys. This article comprehensively reviews the current state of ultrasonic spot welding of copper alloys with a number of critical issues including materials flow, plastic deformation, temperature distribution, vibration, relative motion, vertical displacement, interface friction coefficient, online monitoring technique, coupled with the macrostructure and microstructure, the mechanical properties and electrical conductivity. In addition, the future trends in this field are provided.     

施工中电焊机的安全使用简述

从电焊机自身电气特点及建筑工地工作环境入手,探讨电焊机安全技术的实施方法。分析电焊机安全隐患及事故的分类以及电焊机在使用过程中产生危险的原因。介绍电焊机在安装以及作业过程中的安全措施。     

尿素装置液位仪表失真分析及处理

介绍了尿素装置中3起液位仪表失真案例,分析了故障现象和设备工况,确定失真原因,采取了相应的处理措施,解决了仪表故障。     

非径向管板焊接接头的超声检测

对AP1000压水堆核电站安全壳贯穿件的非径向管板焊接接头结构特点进行了介绍,并分析其超声检测工艺的重点和难点。通过建立统一的缺陷定位坐标系并结合被检构件的几何特点进行综合分析,推导得出了h值(缺陷回波最高点距套管外壁的距离)的计算方法。为超声检测对这类焊接接头缺陷的准确识别和定位提供了行之有效的方法,为解决这类焊接接头的超声检测技术受限区提供了行之有效的措施。     

Linear friction welding of Ti6Al4V: experiments and modelling

Linear friction welding of the Ti6Al4V alloy is studied. A new definition of the energy input rate is proposed, based on an integration over time of the in-plane force and velocity; a strong correlation with the upset rate is then found. The effective friction coefficient is estimated to be 0·5±0·1 for varying frequencies and amplitudes, with only a weak dependence on the processing conditions displayed. A model is proposed that accounts for both the conditioning and equilibrium stages of the process, which is shown to be in good agreement with the experimental data. The model is used to study the mechanism by which the flash is formed. A criterion is proposed by which the rippled nature of its morphology can be predicted.     

Process and joint quality of ultrasonic vibration enhanced friction stir lap welding

In order to improve the process effectiveness and joint quality, ultrasonic vibrations were integrated with friction stir lap welding. Effect of ultrasonic exertion on the process and joint quality of AA 6061-T6 were investigated. Upon ultrasonic exertion, joints owned larger effective lap width, shorter hooks and improved strength. Weld fracture mode changed from a ductile–brittle mixed mode to a more ductile mode while the fracture path shifted from lap interface to beyond the stir zone. Material flow and interface defects were characterised using lap welded dissimilar aluminium alloy joints. Ultrasonic vibration improved the material flow and reduced the interfacial defects. Variations in failure load of joints were found in accordance with the variations in material flow and interfacial defects.     

Improving weld formability by a novel dual-rotation bobbin tool friction stir welding

A novel dual-rotation bobbin tool friction stir welding (DBT-FSW) was developed, in which the upper shoulder (US) and lower shoulder (LS) have different rotational speeds. This process was tried to weld 3.2 mm thick aluminum-lithium alloy sheets. The metallographic analysis and torque measurement were carried out to characterize the weld formability. Experimental results show that compared to conventional bobbin tool friction stir welding, the DBT-FSW has an excellent process stability, and can produce the defect-free joints in a wider range of welding parameters. These can be attributed to the significant improvement of material flow caused by the formation of a staggered layer structure and the unbalanced force between the US and LS during the DBT-FSW process.     

二氧化碳气体保护焊在厚板上的应用

板厚为 5 5mm的 16Mn钢采用CO2 半自动气保焊建造大型转炉炉体的可能性和可靠性如何 ?目前尚缺少足够的试验数据。为了给转炉工程的施工焊接提供可靠数据 ,确保焊接质量 ,对板厚 5 5mm16Mn钢CO2 半自动的焊接性能进行了一系列的试验研究     

含氮金刚石结构中Jahn-Teller畸变效应的计算

研究了由J.Bourgoin和M.Lannoo提出的半导体内Jahn-Teller畸变效应的计算理论。应用Bourgoin和Lannoo的方法研究了含中心氮杂质金刚石结构的Jahn-Teller畸变问题,计算了34C+N簇团的T2模耦合沿%111&晶向的Jahn-Teller畸变效应,结果与实验相符。