Development and validation of a micro-fin tubes evaporator model using R134a and R1234yf as working fluids

This paper presents a model of shell and tube evaporator with micro-fin tubes using R1234yf and R134a. The model developed for this evaporator uses the ε-NTU method to predict the evaporating pressure, the refrigerant outlet enthalpy and the outlet temperature of the secondary fluid. The model accuracy is evaluated using different two-phase flow boiling correlations for micro-fin tubes and comparing predicted and experimental data. The experimental tests were carried out for a wide range of operating conditions using R134a and R1234yf as working fluids. The predicted parameter with maximum deviations, between the predicted and experimental data, is the evaporating pressure. The correlation of Akhavan– Behabadi et al. was used to predict flow boiling heat transfer, with an error on cooling capacity prediction below 5%. Simulations, carried out with this validated model, show that the overall heat transfer coefficient of R1234yf has a maximum decrease of 10% compared with R134a.     

中铝河南分公司矿山在土地复垦中的有益探索

分析了铝土矿露天开采和土地、环境之间的利害关系，并对矿山公司“土地复垦”工艺技术进行了阐述，介绍了中铝河南分公司矿山公司方面的具体作法和成功经验。     

Quasi-static and dynamic crushing behaviors of aluminum and steel tubes with a cutout

Tubular members are commonly used as an energy absorber in engineering structures and many such members have a cutout. In this study, the crushing behaviors of tubes with a cutout are characterized and the effects of cutout on the energy absorption capabilities of these tubes are quantified. Systematic parametric studies were carried out to study the effect of material properties, including yield and ultimate strength of material, strain rate effect, location of cutout, tube length and impact speed on the crushing behaviors and energy absorption capacity of aluminum and steel tubes. First, a numerical model was constructed with a commercial explicit finite element code. It will be first proven that the numerical simulation can produce sufficiently accurate results in an economic manner. Subsequently, the crushing behavior of aluminum and steel tubes with a cutout was experimentally characterized and their energy absorption capacity was evaluated in terms of mean crushing force, peak crushing force and specific energy absorption (SEA). Tubes of various lengths with a cutout located at different locations, subject to both quasi-static and dynamic impact loadings were considered. For steel tubes, the numerical simulation investigated the influence of the strain rate effect and variation in strain hardening ratio of the material. Empirical equations describing the mean and peak crushing forces of aluminum and steel tubes with a cutout were developed using linear and nonlinear regression methods applied to the results obtained from the numerical and experimental studies.     

Efficient primal-dual heuristic for a dynamic location problem

In this paper the dynamic location problem with opening, closure and reopening of facilities is formulated and an efficient primal-dual heuristic that computes both upper and lower limits to its optimal solution is described. The problem here studied considers the possibility of reconfiguring any location more than once over the planning horizon. This problem is NP-hard (the simple plant location problem is a special case of the problem studied). A primal-dual heuristic based on the work of Erlenkotter [A dual-based procedure for uncapacitated facility location. Operations Research 1978;26:992–1009] and Van Roy and Erlenkotter [A dual-based procedure for dynamic facility location. Management Science 1982;28:1091–105] was developed and tested over a set of randomly generated test problems. The results obtained are quite good, both in terms of the quality of lower and upper bounds calculated as in terms of the computational time spent by the heuristic. A branch-and-bound procedure that enables to optimize the problem is also described and tested over the same set of randomly generated problems.     

A method for evaluating the mechanical performance of thin-walled titanium tubes

A method which was developed to compare the stress–strain properties of three types of thin-walled, commercially pure titanium tubes is presented. The tubes were of types intended for use in large heat-exchanger applications and were to be subjected to significant plastic deformation during subsequent assembly processes. It had been anticipated that small differences in chemical composition and tube-drawing treatment would produce quite different characteristics. It is known that the properties of titanium can exhibit considerable degrees of anisotropy, especially for wrought products; although axial properties of the materials could be evaluated using standard test equipment and procedures, a novel testing system had to be designed to allow the circumferential properties to be assessed. Significant differences between tube types were observed and anisotropic material behaviour was apparent.     

An efficient procedure for finding best compromise solutions to the multi-objective assignment problem

In this paper, we consider the problem of determining a best compromise solution for the multi-objective assignment problem. Such a solution minimizes a scalarizing function, such as the weighted Tchebychev norm or reference point achievement functions. To solve this problem, we resort to a ranking (or k-best) algorithm which enumerates feasible solutions according to an appropriate weighted sum until a condition, ensuring that an optimal solution has been found, is met. The ranking algorithm is based on a branch and bound scheme. We study how to implement efficiently this procedure by considering different algorithmic variants within the procedure: choice of the weighted sum, branching and bounding schemes. We present an experimental analysis that enables us to point out the best variants, and we provide experimental results showing the remarkable efficiency of the procedure, even for large size instances.     

大型管壳式换热器管-管板连接的可靠性措施

从材料性能、管孔的结构及加工要求、管与管板的连接形式等影响换热器管与管板连接接头强度的因素出发 ,结合乙烯大型换热器E EA12 3F的制造提出了管与管板连接接头的可靠性措施     

Improved GPU SIMD control flow efficiency via hybrid warp size mechanism

High single instruction multiple data (SIMD) efficiency and low power consumption have made graphic processing units (GPUs) an ideal platform for many complex computational applications. Thousands of threads can be created by programmers and grouped into fixed-size SIMD batches, known as warps. High throughput is then achieved by concurrently executing such warps with minimal control overhead. However, if a branch instruction occurs, which assigns different paths to different threads, one warp will be broken into multiple warps that have to be executed serially, consequently reducing the efficiency advantage of SIMD. In this paper, the contemporary fixed-size warp design is abandoned for a hybrid warp size (HWS) mechanism. Mixed-size warps are generated according to HWS and are scheduled and issued flexibly. The simulation results show that this mechanism yields an average speedup of 1.20 over the baseline architecture for a wide variety of general purpose GPU applications. The paper also integrates HWS with dynamic warp formation (DWF), which is a well-known branch handling mechanism used to improve SIMD utilization by forming new warps out of split warps in real time. The simulation results show that the combination of DWF and HWS generates an average speedup of 1.27 over the DWF-only platform with an estimated area increase of about 1% of DWF.     

对新常态下加强基层党支部建设的思考

基层党支部是党在社会基层组织中的战斗堡垒,是从思想上、政治上凝聚团结广大群众的核心,是基层各项工作的组织者,是贯彻落实党的方针路线政策的决定性力量。当前形势下,我国经济步入新常态,适应新常态必须加强基层党建工作,针对党支部地位、作用弱化、组织教育缺乏活力、队伍建设有待加强等问题,笔者提出自己的几点思考。