Composition and morphology of char particles of fly ashes from industrial burning of high-ash coals with different reactivity

A comparative investigation of the composition and the morphology of char particles was conducted: char particles were recovered from fly ashes of two power stations in Russia from burning of high- and low-reactivity high-ash coals; the known results of studies of char particles generated in laboratory conditions from coals characterized according to the ASTM D388-98a standard were also used. The composition of organic and mineral components of different fraction char particles was studied. An inverse correlation between the content of the organic substance and the iron content in char particles was identified. The morphology of the char particles for the three main types (Cenospheric, Network and Solid) and the influence of coal reactivity and temperature on char morphology were investigated. The morphology of the mineral component of char particles of the two varieties of coals was also studied. It was shown that the high-temperature of industrial burning of Ekibastuz coal results in melting of the mineral substance and forming of micron-scale microspheres located in the lamellar porous structure of the carbon matrix.     

Preparation of brush-like crystals of poly[2,6-(1,4-phenylene)-benzobisimidazole]

Poly[2,6-(1,4-phenylene)-benzobisimidazole] (PPBI) crystals were prepared by using reaction-induced crystallization of oligomers during solution polymerization of 1,2,4,5-tetraaminobenzene and diphenyl terephthalate. Polymerizations were carried out at a monomer concentration of 4.3 × 10⁻² mol L⁻¹ at 350 °C for 6 h. Brush-like PPBI crystals were obtained in a mixture of structural isomers of dibenzyltoluene, in which many needle-like crystals came out vertically from the surface of the ribbon-like crystals. Average width and thickness of the ribbon-like crystals were 0.75 μm and 0.11 μm, respectively. And average length and diameter of the needle-like crystals were 0.36 μm and 50 nm, respectively. The brush-like crystals possessed high crystallinity and exhibited good thermal resistance. The ribbon-like crystals were formed by the crystallization of imidazole oligomers at an initial stage of polymerization, and then the needle-like crystals grew from the surface of the ribbon-like crystals. Polymerization occurred on the crystals when the oligomers were crystallized, leading to the high molecular weight PPBI crystals.     

Morphological changes in poly(?-caprolactone) in dense carbon dioxide

Morphological changes that take place in poly(?-caprolactone) upon exposure to carbon dioxide at high pressures have been explored as a function of pressure and temperature. SEM and DSC results point to a competition between CO₂-modulated crystallization and pressure-induced phase separation which leads to unique morphologies. At 293 K, exposure to CO₂ at pressures up to 45 MPa leads to recrystallization resulting in higher level of crystallinity and higher melting temperatures. Highest crystallinity levels along with distinct crystal morphology were observed after exposure to CO₂ at 308 K and 21 MPa. At a higher pressure at this temperature (308 K/34 MPa) polymer undergoes melting, and foaming is achieved during depressurization prior to solidification. At 323 K, the polymer is found to display unique crystal morphology with concave crystal geometry as well as porous domains. The results are discussed in terms of the crystallization and phase separation paths that are followed during exposure to CO₂ and the depressurization stages.     

The deposition morphology of Brownian/non-Brownian particles within a constricted tube

The deposition morphology of Brownian/non-Brownian particles within a constricted tube is investigated by applying the Brownian dynamics simulation method in the present paper. Two different geometric structures, the parabolic constricted tube (PCT) and the sinusoidal constricted tube (SCT), are adopted. The effect of various types of the total interaction energy curves of the Derjaguin-Landau-Verwey-Overbeek (DLVO) theory, and of the shadow area cast by those deposited particles, on the particles’ collection efficiencies are also examined. For the PCT structure, under the same interaction energy curve, it is found that the non-Brownian particles always own a higher collection efficiency than that of the Brownian particles. Since the deposition location moves closer to the constriction part of the tube, the collection efficiencies of the Brownian/non-Brownian particles increase with the decrease of flow velocity. The SCT behaves differently, it is found that the collection efficiencies of non-Brownian particles are only slightly higher than those of Brownian particles when SCT is adopted. The steep slope of the tube wall near the constriction part of SCT dominates the whole deposition process of Brownian/non-Brownian particles. In comparison with the available experimental data, it is found that the present method can give a good simulation result.     

Unified reliability estimation and management of NoC based chip multiprocessors

We present a new architecture level unified reliability evaluation methodology for chip multiprocessors (CMPs). The proposed reliability estimation (REST) is based on a Monte Carlo algorithm. What distinguishes REST from the previous work is that both the computational and communication components are considered in a unified manner to compute the reliability of the CMP. We utilize REST tool to develop a new dynamic reliability management (DRM) scheme to address time-dependent dielectric breakdown and negative-bias temperature instability aging mechanisms in network-on-chip (NoC) based CMPs. Designed as a control loop, the proposed DRM scheme uses an effective neural network based reliability estimation module. The neural-network predictor is trained using the REST tool. We investigate how system’s lifetime changes when the NoC as the communication unit of the CMP is considered or not during the reliability evaluation process and find that differences can be as high as 60%. Full-system based simulations using a customized GEM5 simulator show that reliability can be improved by up to 52% using the proposed DRM scheme in a best-effort scenario with 2–9% performance penalty (using a user set target lifetime of 7 years) over the case when no DRM is employed.     

Pore network model of deactivation of immobilized glucose isomerase in packed-bed reactors II: three-dimensional simulation at the particle level

Immobilized glucose isomerase is widely used for converting glucose to fructose by enzymatic isomerization. The process takes place in a packed-bed reactor consisting of mesoporous particles with distributed pore sizes and interconnectivities. Its efficiency is, however, significantly affected by deactivation of the mesoporous particles. In this paper, we study deactivation of the mesoporous particles using a three-dimensional pore network model of the pore space with distributed pore sizes and interconnectivities, and investigate several plausible mechanisms of deactivation of the porous particles. The results of the present study, which will be used as the input for simulation of the phenomenon at the reactor level, demonstrates the strong effect of the particles’ morphology on the deactivation process.     

智能耳诊机的软、硬件设计

本文从实际应用出发,详尽论述了“智能耳诊机”软、硬件设计的方法。对从事单片机开发应用的工程技术人员有较高的参考价值。     

An electron tomography algorithm for reconstructing 3D morphology using surface tangents of projected scattering interfaces

Upon discerning the mere shape of an imaged object, as portrayed by projected perimeters, the full three-dimensional scattering density may not be of particular interest. In this situation considerable simplifications to the reconstruction problem are possible, allowing calculations based upon geometric principles. Here we describe and provide an algorithm which reconstructs the three-dimensional morphology of specimens from tilt series of images for application to electron tomography. Our algorithm uses a differential approach to infer the intersection of projected tangent lines with surfaces which define boundaries between regions of different scattering densities within and around the perimeters of specimens. Details of the algorithm implementation are given and explained using reconstruction calculations from simulations, which are built into the code. An experimental application of the algorithm to a nano-sized Aluminium tip is also presented to demonstrate practical analysis for a real specimen.

Program summary

Program title: STOMO version 1.0Catalogue identifier: AEFS_v1_0Program summary URL:http://cpc.cs.qub.ac.uk/summaries/AEFS_v1_0.htmlProgram obtainable from: CPC Program Library, Queen's University, Belfast, N. IrelandLicensing provisions: Standard CPC licence, http://cpc.cs.qub.ac.uk/licence/licence.htmlNo. of lines in distributed program, including test data, etc.: 2988No. of bytes in distributed program, including test data, etc.: 191 605Distribution format: tar.gzProgramming language: C/C++Computer: PCOperating system: Windows XPRAM: Depends upon the size of experimental data as input, ranging from 200 Mb to 1.5 GbSupplementary material: Sample output files, for the test run provided, are available.Classification: 7.4, 14External routines: Dev-C++ (http://www.bloodshed.net/devcpp.html)Nature of problem: Electron tomography of specimens for which conventional back projection may fail and/or data for which there is a limited angular range. The algorithm does not solve the tomographic back-projection problem but rather reconstructs the local 3D morphology of surfaces defined by varied scattering densities.Solution method: Reconstruction using differential geometry applied to image analysis computations.Restrictions: The code has only been tested with square images and has been developed for only single-axis tilting.Running time: For high quality reconstruction, 5-15 min     

Optimization of screen-printing parameters of SN9000 ink for pinholes using Taguchi method in chip on film packaging

The influence of pinholes on the chip on film (COF) in screen-printing was studied in this paper. Yield improvement is the most challenging part of COF manufacturing in view of its processing complexity, mainly in the screen-printing process. The process parameters such as ink capacity, origin control distance, angle of the squeezer, method of mixing, freshness of ink, speed of printing, and speed of scraper are considered to improve the pinholes. In Taguchi method, a two level orthogonal array is used to determine the signal-to-noise (S/N) ratio. Analysis of variance and the F-test values are used to determine the most significant process parameters affecting the pinholes. Confirmation analysis tests with the optimal levels of process parameters are carried out. The results of the experiment show that Taguchi method is a very suitable approach with regard to solving quality problems related to such pinholes.     

8098单片机测速道口防护系统的研究

为保证铁路安全，讨论了在我国众多的铁路与公路的平交道口设立新型测速 道 口护系统的必要性，提出了８０９８单片机否则 的构可行性，并且对系统的软件，硬件的主要组成单元进行了分析。