基于全U网络的混凝土路面裂缝检测算法

针对现有的混凝土裂缝检测算法在各种复杂环境中检测精度不够、鲁棒性不强的问题,根据深度学习理论和U-net模型,提出一种全U型网络的裂缝检测算法。首先,依照原U-net模型路线构建网络;然后,在每个池化层后都进行一次上采样,恢复其在池化层之前的特征图规格,并将其与池化之前的卷积层进行融合,将融合之后的特征图作为新的融合层与原U-net网络上采样之后的网络层进行融合;最后,为了验证算法的有效性,在测试集中进行实验。结果表明,所提算法的平均精确率可达到83.48%,召回率为85.08%,F1为84.11%,相较于原U-net分别提升了1.48%,4.68%和3.29%,在复杂环境中也能提取完整裂缝,保证了裂缝检测的鲁棒性。     

Interface regulation effects on mechanical behavior of heterostructure Ti6Al4V/TiAl-based laminated composite sheets

Design of architectured composites with layered-ordered structure can solve the strength-toughness mismatch problem of structural materials. In the present study, heterostructure Ti6Al4V/TiAl laminated composite sheets with different thicknesses of interface layer and TiAl composite layer were successfully produced by hot-pressing technology. The effects of interface regulation and laminated structure on their mechanical properties, crack propagation, and fracture behavior were studied. The results indicated that compressive strength of the sheets increased with the decrease in interface thickness. Compressive strength of TiAl composite sheet with thicker composite layer reached 1481.55 MPa at the arrester orientation with sintering holding time of 40 min, which was 25.96% higher than that of the sheet obtained at 120 min. Analysis indicated that the interface area transferred stress through slip bands and through-interface cracks. Compressive strength at the divider orientation reached 1443.06 MPa, which was 45.78% higher than that of the sheet obtained at 120 min. In this case, the interface area transferred stress through slip bands and along-interface cracks. For TiAl composite sheets with thinner composite layer, compressive strength was further improved to 1631.01 MPa and 1594.66 MPa at the arrester and divider orientations with sintering holding time of 40 min, respectively. The ductile metal layer exerted a significant toughening effect. Both interface regulation and laminated structure transformation could enhance the hetero-deformation induced (HDI) strengthening and improve the comprehensive mechanical properties of the composite sheets.     

Semirigid inclusions in elastic bodies: Mechanical interplay and optimal control

The paper concerns an analysis of an equilibrium problem for 2D elastic body with two semirigid inclusions. It is assumed that inclusions have a joint point, and we investigate a junction problem for these inclusions. The existence of solutions is proved, and different equivalent formulations of the problem are proposed. We investigate a convergence to infinity of a rigidity parameter of the semirigid inclusion. It is proved that in the limit, we obtain an equilibrium problem for the elastic body with a rigid inclusion and a semirigid one. A parameter identification problem is investigated. In particular, the existence of a solution to a suitable optimal control problem is proved.     

高分子表面活性剂对超声辐照下苯乙烯乳液聚合的影响

在超声辐照引发苯乙烯乳液聚合中加入一种新型的以羧甲基纤维素为基础的高分子表面活性剂(CMC—A9)，讨论了高分子表面活性剂对反应动力学的影响。实验表明，超声辐照下初级自由基并非由通常认为的高分子表面活性剂产生，而是十二烷基硫酸钠在超声辐照下断裂，产生自由基。通过对反应动力学的研究，发现超声辐照下乳液聚合机理不同于常规乳液聚合，聚合反应过程只有两个阶段，即加速期和减速期，不存在恒速期。加入CMC—A9高分子表面活性剂，可以在较短的时间内和较低的超声功率下达到较高的单体转化率。     

NSA-500-1型氩弧焊机VD9不同接法对引弧和稳弧的影响

从一起NSA－500－1型氩弧焊机故障，分析其高压脉冲旁路二极管VD9不同接法对引弧、稳弧及设备安全的影响。     

On the corrosion fatigue crack initiation model and expression of metallic notched elements

In the present study, attempts are made to extend the application of the mechanical model for the fatigue crack initiation (FCI) and the FCI life formula of metallic notched elements in laboratory air to those in the corrosive environment. The test results and analysis of the corrosion FCI (CFCI) life of aluminum alloys and Ti---6A1---4V show that the expression of the CFCI life obtained by modifying the FCI life formula in laboratory air can give a good fit to the test results of the CFCI life. The salt water (3.5% NaCl) environment has no effects on the CFCI resistant coefficient compared with the FCI resistant coefficient in laboratory air. However, 3.5% NaCl environment greatly decreases the CFCI threshold of aluminum alloy, but has little effect on the CFCI threshold of Ti---6A1---4V. The loading frequency ranging from 1 Hz to 10 Hz has no appreciable effect on the CFCI life, and thus, the CFCI threshold of aluminum alloys investigated. Hence, the expression for the CFCI life of metallic notched elements proposed in this study is a better one, which reveals a correlation between the CFCI life and the governing parameters, such as, the geometry of the notched elements, the nominal stress range, the stress ratio, the tensile properties and the CFCI threshold. However, this new expression of the CFCI life needs to be verified by more test results.     

中厚板轧制边部不均匀变形机理的探讨

通过分析宽中厚板轧制过程中的边部不均匀变形，探讨了其影响因素及大宽度板“切边纵裂”的产生原因，提出了解决问题的具体办法。     

峡口水库沥青混凝土面板的施工与试验

以灌溉、防洪为主的峡口水库大坝，为沥青混凝土面板堆石坝，为研究低温抗裂性能，对沥青混凝土面板破损取样，进行了配比和多种力学性能试验，并与原面板设计指标进行了对比。由于面板经受住了－20℃以下的低温考验，其所用沥青指标、破损取样试验结果，特别是冻断低温指标，对确定水工沥青混凝土低温抗裂检验标准有重要参考价值。     

Nondestructive evaluation of the characteristics of degraded materials using backward radiated ultrasound

The frequency dependency of Rayleigh surface wave is investigated indirectly by measuring the angular dependency of the backward radiation of the incident ultrasonic wave in two kinds of degraded specimens by scuffing or corrosion. Then, the frequency dependency is compared with the residual stress distribution or the corrosion-fatigue characteristics for the scuffed or corroded specimens, respectively. The width of the backward radiation profile increases with the increase of the variation in residual stress distribution for the scuffed specimens. In the corroded specimens, the profile width decreases with the increase of the effective aging layer thickness and is inversely proportional to the exponent, m, in the Paris’ law that can predict the crack size increase due to fatigue. The result observed in this study demonstrates high potential of backward radiated ultrasound as a tool for nondestructive evaluation of subsurface gradient of material degradation generated by scuffing or corrosion.