Dependence of mechanical and tribological performance on the microstructure of (CrAlTiNbV)Nx high-entropy nitride coatings in aviation lubricant

The (CrAlTiNbV)N_x coatings are fabricated by controlling the substrate bias via magnetron sputtering method. Under low substrate bias, the coating tends to form a loose columnar crystal structure with (200) preferred orientation. However, when the substrate bias increases, the coating transforms into a dense nanocrystalline structure, and the (111) orientation is enhanced. As the substrate bias increases, the residual stress and hardness of the coating gradually increase, while the adhesion strength decreases slightly. Friction tests show that the coating possesses the lowest average friction coefficient (about 0.06) and wear rate (8.7 × 10^-9 mm³/N·m) in 4050# aviation lubricant, which is achieved under the substrate bias of -96 V and -126 V, respectively.     

The effect of a solid additive on rolling fatigue life

Behaviour of a series of lubricant oils and the effect of a non stoichiometric inorganic compound, as solid extreme pressure additive, on rolling fatigue life are studied using the rolling four-ball accelerated service simulation test proposed by Barwell and Scott. The results show, in all tested cases, the remarkable efficacy of this type of additive. The Total Acidity Number (tan) was found to increase with performance time for the case of the base lubricant, while for the oils with additives, it remained at its constant low value. This led to a proposal of a possible mechanism of the additive performance in the rolling process.     

未增塑聚氯乙烯(PVC-U)异型材配方基础

PVC-U异型材配方十分复杂,常用原料通常在10种以上。根据大连实德集团实际生产情况,这10多种原料通常以7大组分的方式进行配料和生产。文中就该配方中7大组分的分类、特点及应用情况分别进行了详细介绍。     

Complementary effects of solid lubricants in the automotive brake lining

An experimental investigation was carried out to examine the tribological behavior of NAO (non-asbestos organic) type brake linings containing different volume ratios of graphite and antimony trisulfide (Sb₂S₃). A scale dynamometer was used for friction tests and particular emphases were given to the effect of applied pressure, sliding speed, and temperature on the coefficient of friction according to the relative amounts of the two solid lubricants. Results showed that the brake linings with both solid lubricants exhibited better friction stability and less speed sensitivity than the friction materials containing a single solid lubricant. In particular, the brake lining containing higher concentrations of graphite showed better fade resistance than others during high-temperature friction test.     

石油一厂东蒸馏装置的技术改造

介绍抚顺石油化工公司石油一厂东蒸馏装置的改造情况，通过技术改造，使减压蒸馏塔由生产燃料型改造成生产石蜡－润滑油型，满足了该厂对石蜡和润滑油料的质量要求。     

2-巯基苯并噻唑衍生物摩擦学性能的研究

合成了S—(1—(2—苯并噻唑基巯基)—2—羟基)—丙基N，N—二烷基二硫代氨基甲酸酯和S—(1—(2—苯并噻唑基巯基)—2—乙酰基)—丙基N，N—二烷基二硫代氨基甲酸酯两种化合物。运用IR、MS、HNMR和元素分析等分析方法对其结构进行表征。用四球试验、HQ—l环块试验分别考察了其对润滑油的极压承载能力及抗磨减摩性能的影响。结果表明：在350SN中性油中添加所合成的化合物后可以显著降低四球长磨后磨斑直径、有效地降低摩擦副之间的摩擦系数，拥有优良的摩擦学性能。     

润滑油基础油的现状及发展趋势

叙述了内燃机油的发展对基础油的要求，并对传统工艺和加氢工艺生产的基础油质量状况进行了分析，指出润滑油加氢工艺是提高基础油质量的有效途径。加氢工艺生产基础油是润滑油的发展趋势。     

热轧无缝钢管芯棒润滑剂

介绍了用于热轧无缝钢管芯棒的新型石墨润滑剂的高温润滑性能，润滑机组及工业使用情况。实践证明，新型石墨润滑剂完全满足热轧无缝钢管的工艺要求，并与进口产品性能相似，且具有操作简便、环境污染小等优点。     

Tribological behavior of high specific strength PTFE-Al alloy composite

Solid lubricants lead to substantial weight savings relative to the use of liquid lubricant, especially in the weight-conscious aerospace industry. A new PTFE-Al alloy composite（A） containing 60% area proportion of PTFE composite was developed. Another type of common metal-plastics multilayer composite, also called DU, was selected for a comparative investigation. Friction and wear tests were carried out in an oscillating sliding tribotester in air at an oscillating frequency of 0.13 Hz and contact mean pressures from 10 to 80 MPa. The composites slid against a 38CrMoAlA steel shaft. The results show that the composite A exhibits low coefficient of dry sliding friction less than 0.1 and long wear life of 2 000 m. This is because the composite A can provide a sufficient solid lubrication during the whole tests. SEM examination of the transfer films for the composite A confirms that uniform, thin and coherent transfer films are prerequisites for low friction and good wear resistance.     

水基传送带润滑剂综述

说明了水基传送带润滑剂的作用机理、性能要求,详细介绍了现有的水基传送带润滑剂的特点,并简单介绍了水基传送带润滑剂的发展前景和趋势。