Experimental investigation of unconfined spherical and cylindrical flame propagation in hydrogen-air mixtures

This paper presents results of experimental investigations on spherical and cylindrical flame propagation in pre-mixed H₂/air-mixtures in unconfined and semi-confined geometries. The experiments were performed in a facility consisting of two transparent solid walls with 1 m² area and four weak side walls made from thin plastic film. The gap size between the solid walls was varied stepwise from thin layer geometry (6 mm) to cube geometry (1 m). A wide range of H₂/air-mixtures with volumetric hydrogen concentrations from 10% to 45% H₂ was ignited between the transparent solid walls. The propagating flame front and its structure was observed with a large scale high speed shadow system. Results of spherical and cylindrical flame propagation up to a radius of 0.5 m were analyzed. The presented spherical burning velocity model is used to discuss the self-acceleration phenomena in unconfined and unobstructed pre-mixed H₂/air flames.     

Effect of grinding-induced cyclic heating on the hardened layer generation in the plunge grinding of a cylindrical component

This paper discusses the effects of the grinding-induced cyclic heating on the properties of the hardened layer in a plunge cylindrical grinding process on the high strength steel EN26. It was found that a multi-pass grinding brings about a uniform and continuous hardened layer along the circumference of the cylindrical workpiece. An increase of the number of grinding passes, leads to a thicker layer of hardening, a larger compressive residual stress and a deeper plastic deformation zone. Within the plastic deformation zone, the martensitic grains are refined by the thermo-mechanical loading, giving rise to a hardness of 12.5% higher than that from a conventional martensitic transformation. The coupled effects of heat accumulation and wheel wear in the multi-pass grinding are the main causes for the thickening of the hardened layer. A too small infeed per workpiece revolution would result in insufficient grinding heat, and in turn, bring about an undesirable tempered hardened layer and a reduction of its hardness.     

介质加载圆柱腔的场分析

本文应用严格场匹配法解决了介质加载圆柱腔的本征问题，计算了圆柱腔在纵向部分填充介质后ＴＥ０１ｎ模和ＴＭ０１ｎ模的本征频率和本征场型的变化。特别分析了本征模式在空气段为截止模的情况。本文的分析方法亦可应用到纵向部分填充介质的传输线和其它形状的谐振腔。     

Flow of granules through cylindrical hopper

The gravity flow characteristics of pharmaceutically important granules were studied in a cylindrical hopper with attachable orifice disk at the bottom. Results indicate that materials property and orifice diameter play key role in determining mass flow rate while keeping environmental condition (temperature) at fixed range. A new dimensionally analyzed equation was developed to predict gravity flow of pharmaceutically important granules. The developed correlation agreed well with the experimental data. Calcium gluconate and lactose were used for preparing granules. Generally, glidant/lubricant materials are added to pharmaceutical granules during tablet manufacturing process, in order to improve physical property of granular material. Hence, the effect of glidant/lubricant on mass flow of granules through hopper was also studied. Magnesium stearate (1.5%) was added as glidant before granulation.     

薄壁压力容器筒体纵焊缝角变形对应力的影响

提出压力容器简体纵焊缝产生角变形的模型。用简明的解析方法和有限元方法,探讨由变形引起的应力集中系数K_(ta)。结果表明,利用应力集中系数估算焊缝棱角对应力的影响是较合实际的,其公式为:K_(ta)=1+6E/S,式中E为棱角度,S为筒体壁厚。     

Critical stress and load conditions for pitting calculations of involute spur and helical gear teeth

Calculation methods of spur and helical gear drives for preliminary designs or standardization purposes available in technical literature, use the Hertz equation to evaluate the contact stress, assuming the load to be uniformly distributed along the line of contact. However, this model presents some discrepancies with experimental results because the changing rigidity of the pair of teeth along the path of contact produces a non-uniform load distribution, which implies that some load distribution factors are required to compute the contact stress. In this paper, a non-uniform model of load distribution along the line of contact, recently developed, obtained from the minimum elastic potential criterion, has been used. This model combined with the Hertz equation yields more accurate values of the contact stress. As the load per unit of length at any point of the line of contact and any position of the meshing cycle has been described by a very simple analytic equation, a complete study of the location and value of the critical contact stress has been carried out. From this study, a recommendation for the calculation of the pitting load capacity of spur and helical gears is proposed.     

Effects of bottom profile on the circulation and classification of particles in cylindrical hydrocyclones

The cylindrical hydrocyclone has been increasingly used in coarse classification due to its reduced fine particle entrainment, but the loss of coarse particles to overflow remains an intractable problem. Based on the notion that the strong circulation flow caused by the flat bottom structure bears primary responsibility for the problem, this study designs eight unique bottom profiles to regulate the particle circulating flow and attempts to correlate particle circulation flow with classification performance. The effects of the bottom profile on flow field characteristics, particle spatial distribution, circulation flow rates, and grade efficiency are explored in detail using validated models in a Φ200 mm cylindrical hydrocyclone. The findings suggest that bottom profiles have the greatest effect on the axial velocity near the bottom and the grade efficiency of intermediate and coarse particles, while all unique designs have the potential to lower turbulence intensity. An ascending segment near the wall or a descending segment near the axis can help to mitigate the misplacement of coarse particles by reducing particle circulation flow without affecting the entrainment of fines appreciably. Additionally, two circles are found on each side of the cut plane, which is conducive to releasing coarse particles from the circulation flow. Regulation of particle circulation flow by adjusting bottom profile parameters can improve separation performance.     

Computing integrals over polynomially defined regions and their boundaries in 2 and 3 dimensions

We use the cylindrical algebraic decomposition algorithms implemented in Mathematica to produce procedures to analytically compute integrals over polynomially defined regions and their boundaries in two and three dimensions. Using these results, we can implement the divergence theorem in three dimensions or the Green's theorems in two dimensions. These theorems are of central importance in the applications of multidimensional integration. They also provide a strong correctness test for the implementation of our results in a computer algebra system. The resulting software can solve many of the two and some of the three dimensional integration problems in vector calculus textbooks. The three dimensional results are being extended. The results in this paper are being included in an automated student assistant for vector calculus.     

复合尼龙附耳薄壁圆筒件超声波焊接破裂分析与解决

介绍了尼龙玻纤复合材料带饶性的薄壁圆筒件超声波焊接时,出现的破裂情况.并对其原因进行了分析.采取有效措施解决了焊接破裂问题,使焊接零件完全合格.