一种新型地雷战斗部的数值模拟研究

针对地雷的毁伤目标和特性,提出一种新颖的多棱柱状药型罩结构,其可看作由八个楔形罩对称排列相邻连接而成。应用非线性有限元软件完成了爆炸载荷下多棱柱状药型罩形成射流过程的数值模拟,结果表明新型药型罩结构能够实现预期设想,形成一股汇聚射流。研究结果为地雷战斗部研究提供了一种新的选择。     

Effect of heat transfer through the release pipe on simulations of cryogenic hydrogen jet fires and hazard distances

Jet flames originated by cryo-compressed ignited hydrogen releases can cause life-threatening conditions in their surroundings. Validated models are needed to accurately predict thermal hazards from a jet fire. Numerical simulations of cryogenic hydrogen flow in the release pipe are performed to assess the effect of heat transfer through the pipe walls on jet parameters. Notional nozzle exit diameter is calculated based on the simulated real nozzle parameters and used in CFD simulations as a boundary condition to model jet fires. The CFD model was previously validated against experiments with vertical cryogenic hydrogen jet fires with release pressures up to 0.5 MPa (abs), release diameter 1.25 mm and temperatures as low as 50 K. This study validates the CFD model in a wider domain of experimental release conditions - horizontal cryogenic jets at exhaust pipe temperature 80 K, pressure up to 2 MPa ab and release diameters up to 4 mm. Simulation results are compared against such experimentally measured parameters as hydrogen mass flow rate, flame length and radiative heat flux at different locations from the jet fire. The CFD model reproduces experiments with reasonable for engineering applications accuracy. Jet fire hazard distances established using three different criteria - temperature, thermal radiation and thermal dose - are compared and discussed based on CFD simulation results.     

Quantitative risk assessment using a Japanese hydrogen refueling station model

Although hydrogen refueling stations (HRSs) are becoming widespread across Japan and are essential for the operation of fuel cell vehicles, they present potential hazards. A large number of accidents such as explosions or fires have been reported, rendering it necessary to conduct a number of qualitative and quantitative risk assessments for HRSs. Current safety codes and technical standards related to Japanese HRSs have been established based on the results of a qualitative risk assessment and quantitative effectiveness validation of safety measures over ten years ago. In the last decade, there has been much development in the technologies of the components or facilities used in domestic HRSs and much operational experience as well as knowledge to use hydrogen in HRSs safely have been gained through years of commercial operation. The purpose of the present study is to conduct a quantitative risk assessment (QRA) of the latest HRS model representing Japanese HRSs with the most current information and to identify the most significant scenarios that pose the greatest risks to the physical surroundings in the HRS model. The results of the QRA show that the risk contours of 10^?3 and 10^?4 per year were confined within the HRS boundaries, whereas the risk contours of 10^?5 and 10^?6 per year are still present outside the HRS. Comparing the breakdown of the individual risks (IRs) at the risk ranking points, we conclude that the risk of jet fire demonstrates the highest contribution to the risks at all of the risk ranking points and outside the station. To reduce these risks and confine the risk contour of 10^?6 per year within the HRS boundaries, it is necessary to consider risk mitigation measures for jet fires.     

Flame characteristics of premixed H2-air mixtures explosion venting in a spherical container through a duct

The explosion venting duct can effectively reduce the hazard degree of a gas explosion and conduct the venting energy to the safe area. To investigate the flame quantitative propagation law of explosion venting with a duct, the effects of hydrogen fraction and explosion venting duct length on jet flame propagation characteristics of premixed H₂-air mixtures were analyzed through experiment and simulation. The experiment results under initial conditions of room temperature and 1 atm show that when hydrogen fraction was high enough, part of the unburned hydrogen was mixed with air again to reach an ignitable concentration, resulting in the secondary combustion was easier produced and the duration of the secondary flame increased. With the increase of venting duct length, the flame front distance and propagation velocity increased. Meanwhile, the spatial distribution of pressure field and temperature field, and the propagation process and mechanism of the flame venting with a duct were analyzed using FLUENT software. The variation of the pressure wave and the pressure reflection oscillation law in the explosion venting duct was captured. Therefore, in the industrial explosion venting design with a duct, the hazard caused by the coupling of venting pressure and venting flame under different fractions should be considered comprehensively.     

CFD Modeling of Active Volume Creation in a Non‐Newtonian Fluid Agitated by Submerged Recirculating Jets

Computational fluid dynamics (CFD) models were employed to investigate flow conditions inside a model reactor in which yield stress non‐Newtonian liquid is mobilized using submerged recirculating jets. The simulation results agree well with the experimental results of active volume in the reactor obtained using flow visualization by the authors in a previous study. The models developed are capable of predicting a critical jet velocity (v_c) that determines the extent of active volume obtained due to jet mixing. The v_c values are influenced both by the rheological properties of the liquid and the nozzle orientation. The liquid with higher effective viscosity leads to higher v_c for a downward facing injection nozzle. However, an upward facing injection nozzle along with a downward facing suction nozzle generates enhanced complementary flow fields which overcome the rheological constraints of the liquid and lead to lower v_c.     

从印刷技术的发展看印刷业的重新定位

近20年以来的技术革命使印刷业发生了脱胎换骨的变化，曾经被认为是技术含量低、员工文化素质低、劳动密集型的印刷业已今非昔比。世界上最先进的电子技术、激光技术、计算机技术及网络技术在印刷领域广泛地应用与发展，改变了人们对印刷的传统思维和行为。在信息时代的今天。印刷业已经成为信息社会的先行行业。在新的形势下，印刷业的经营既离不开生产又离不开增值服务，全面解决方案的推行使印刷业的外延扩大到了第三产业。     

光电摆角动态测量原理及其测量系统

本文阐述了用于测量物体摆角及摆心浮动量的光电动态实时测量原理,以及根据此原理研制的光电导弹喷管摆角动态测量系统。     

APDT-00三极放电管全自动打印机的研制

介绍了新近研制的APTD - 0 0三极放电管全自动打印机的结构特点及整机设计的关键技术 ,阐述了自动上料机构、打印机构和控制电路的设计     

Diffusion Bonded EDM Electrode with Micro Holes for Jetting Dielectric Liquid

This paper describes improvement of machining characteristics of electrical discharge machining of deep slots using a tool electrode which has micro holes for jetting dielectric liquid over the working surface. The tool electrode was made by the diffusion bonding of two copper plates, over an interface on which micro grooves for jetting the dielectric fluid were formed using electrolyte jet machining. In conventional machining, it is difficult to drill micro holes at the end of a slim electrode and circulate the dielectric fluid from the other end. Hence a solid tool electrode is used and periodically lifted up during machining to flush debris particles out of the discharge gap. Use of the newly developed tool electrode was found to shorten the processing time and improve machining accuracy significantly compared with the conventional solid tool electrode. Since the holes are micro, the outlet shapes are not replicated onto the bottom surface of the slot machined.     

An investigation of carbon nanotube jet grinding

Since their observation in 1976 and 1991, carbon nanotubes (CNTs) have generated much interest due to their properties and potential applications. CNTs are tubular carbon molecules with remarkable mechanical, electrical, chemical and thermal properties, which make them useful in various applications. Industries producing CNTs via the fluidized bed chemical vapor deposition technique face challenges related to the size of CNT bundles. The two main challenges are agglomeration and agglomerate size distribution control. A solution to these challenges involves the use of jet mills to grind the CNT agglomerates. The goal of this study was to determine whether the nanotubes could be ground with air jets using a commercial jet mill and apply a two-parameter model to describe the grinding process. The present study has indicated that air-jet grinding of CNTs is feasible with a typical commercial jet mill. This paper presents the effect of operational parameters on the arithmetic mean diameter of the ground product. Sonic velocity through the grinding nozzles was required to obtain reasonable grinding rates and relatively narrow particle size distributions. This occurs at high air to solids feedrate ratios. Additionally, a simple attrition model can describe the grinding process in the spiral jet mill.