Impact behavior and fractographic study of carbon nanotubes grafted carbon fiber-reinforced epoxy matrix multi-scale hybrid composites

Carbon nanotubes are the most promising reinforcement for high performance composites. Multiwall carbon nanotubes were directly grown onto the carbon fiber surface by catalytic thermal chemical vapor deposition technique. Multi-scale hybrid composites were fabricated using the carbon nanotubes grown fibers with epoxy matrix. Morphology of the grown carbon nanotubes was investigated using field emission scanning electron microscopy and transmission electron microscopy. The fabricated composites were subjected to impact tests which showed 48.7% and 42.2% higher energy absorption in Charpy and Izod impact tests respectively. Fractographic analysis of the impact tested specimens revealed the presence of carbon nanotubes both at the fiber surface and within the matrix which explained the reason for improved energy absorption capability of these composites. Carbon nanotubes presence at various cracks formed during loading provided a direct evidence of micro crack bridging. Thus the enhanced fracture strength of these composites is attributed to stronger fiber–matrix interfacial bonding and simultaneous matrix strengthening due to the grown carbon nanotubes.     

光纤布拉格光栅的无源温度补偿

分析了通过施加应变补偿光纤布拉格光栅(FBG)中心波长随温度漂移的原理，给出了一种新型的无源温度补偿的方法和相应的实验结果。该方法采用了两种不同热膨胀系数的金属，对光栅先施加预应变。在0-60℃范围内，中心波长仅偏移了0．02nm。     

DISPERSION COMPENSATION CFBG IN100km 10Gbit／s RECIRCULATING SYSTEMS

A 10Gbit/s recirculating system is configured with Chirped Fiber Bragg Grating (CFBG) for the dispersion compensation. For the first time, the transmission distance in the loop reaches 1000km with bit error rate of 10-9. The effect of the group delay ripple of the fiber grating is also investigated in the recirculating systems, and it is shown that the transmission distance is limited to 4 cycles (4×167.1km ) in the loop with the power penalty fluctuation below 1.0dB. Thus the group delay ripple should be reduced to allow for the wavelength drift of±5GHz. At the end of this letter, the principles are given for designing long haul recirculating systems with dispersion compensation CFBG.     

纤维在沥青混合料中的应用研究

选用工程中常用的几种纤维,结合工程应用要求,试验分析了纤维的吸湿性、耐热性,并通过网篮析漏试验、动态剪切试验和沉锥试验,讨论了纤维对沥青的稳定和吸附作用,以及纤维对沥青混合料“加筋”效果和作用机理。研究表明有的纤维“吸附、稳定”性能好,而有的纤维“加筋、桥接”效果好,在应用纤维时,应根据纤维的主要特点以及沥青混合料的使用要求来选用。     

Improving Short-Circuit Current Capacity, Resistance, and Breaking Load of OPGW Constructions by Modifying Aluminium Alloy With AlB2

This article presents a method that can be applied to molten AA-6101 alloy to improve electrical properties of the aluminium part of the optical ground wire (OPGW) used in overhead transmission lines to protect phase conductors from lightning strike and to transmit signals and data. AA-6101 alloy in casting of the log as 6 m length and 178 mm diameter for extrusion has been inoculated by AlB₂ to decrease detrimental effects of Cr, Ti, V, and Zr on the conductivity of the material. After inoculation, improved billets were extruded as 9.5 mm diameter feedstock. Required wires drawn from the feedstock according to the construction types of OPGW to be tested were exposed to aging at 175°C, 6 h (T-8). Upon completion of the back-twist and performing-type stranding process, resistance, and short-circuit current capacity and breaking load of the OPGW 88/44 constructions with other metal combinations have been examined and tested to show improvement. Results are summarized in tables and graphically.     

Extracting Light from Polymer Light‐Emitting Diodes Using Stamped Bragg Gratings

In this paper, we describe a method for increasing the external efficiency of polymer light‐emitting diodes (LEDs) by coupling out waveguided light with Bragg gratings. We numerically model the waveguide modes in a typical LED structure and demonstrate how optimizing layer thicknesses and reducing waveguide absorption can enhance the grating outcoupling. The gratings were created by a soft‐lithography technique that minimizes changes to the conventional LED structure. Using one‐dimensional and two‐dimensional gratings, we were able to increase the forward‐directed emission by 47 % and 70 %, respectively, and the external quantum efficiency by 15 % and 25 %.     

基于均匀光纤光栅的DWDM系统PMD补偿方法

提出一种基于均匀光纤Bragg光栅(FBG)的透射型密集波分复用(DWDM)系统多信道偏振模色散(PMD)补偿方案。当FBG受到横向挤压时，会产生双折射现象。当一波长的光信号从光栅带隙附近透射时，就会在快轴和慢轴之间产生时延差(DGD)。通过改变外力的大小来调节DGD的大小可以实现对PMD的补偿。通过将多个补偿光栅级联，就可以实现对DWDM系统多信道PMD的补偿。在100N外力作用下，5cm长的光栅最大可以补偿121ps的PMD，而对相邻0．8nm的信道，只引入0．2ps的DGD。     

微机械可调谐滤波器的研制

利用 Ga As/Al Ga As分布反馈 Bragg反射镜在 Ga As衬底上制作了一个微机械的调谐滤波器 .该器件在 7V调谐电压下调谐范围达28nm     

色用缓变光纤中交叉相位调制不稳定性分析

从非线性薛定谔方程出发得到了色散缓变光纤（DDF）中交叉相位调制（XPM）不稳定增益谱。研究了增益谱随入纤功率及光纤纵向色散参量的变化关系。结果表明：反常色散区的增益谱宽比正常色散区宽，且峰值增益高：DDF中XPM不稳定增益谱宽比常规光纤的宽，二者的比值随传输距离和光纤色散参量的乘积成指数增长；DDF的反常色散区是产生调制不稳定的较好的色散介质。