Experimental study on the heat transfer and flow characteristics of nanorefrigerants inside a corrugated tube

The heat transfer and flow characteristics of MWCNT-R141b nanorefrigerant with different mass fractions have been studied through experiments. Experimental results were compared with existing correlations. A two-step method was used to prepare the nanorefrigerants. Span-80 was used as surfactant with an average particle diameter of 20 nm. Transmittance method was used to evaluate the stability of nanorefrigerants. Results showed that the stability of MWCNT-R141b nanorefrigerant, which is the added dispersant, was good during the experiments. The 0.3 wt% MWCNT-R141b nanorefrigerants had optimal heat transfer enhancement effects compared with pure refrigerants. The maximum Nusselt number increased by 40%. The specific pressure drop of nanorefrigerant increased as the Reynolds number (Re) increased, and the specific pressure drop of the pure refrigerant was minimum, which is similar to R141b.     

Theoretical study of a thermoelectric-assisted vapor compression cycle for air-source heat pump applications

This paper proposes a thermoelectric-assisted vapor compression cycle (TVCC) for applications in air-source heat pump systems which could enhance the heating capacity of the system. Performances of TVCC are calculated and then compared with that of basic vapor compression cycle (BVCC). The simulation results show that when coefficients of performance (COPs) of the two cycles are almost equal, the TVCC under maximum COP condition of the thermoelectric modules still performs better than BVCC by 13.0% in heating capacity through selecting the appropriate intermediate temperature. In addition, the TVCC can also achieve an improvement of 16.4%–21.7% in both the heating COP and capacity when compared with the BVCC with an assistant electric heater that is provided with the equivalent power input of thermoelectric heat exchanger. Thus, the TVCC could be beneficial to the applications in small heat pumps if there is always need for auxiliary electric heat.     

Producing fully-lamellar microstructure for wrought beta-gamma TiAl alloys without single α-phase field

Fine-grained fully-lamellar (FL) microstructure is desired for TiAl components to serve as compressor/turbine blades and turbocharger turbine wheels. This study deals with the process and phase transformation to produce FL microstructure for Mo stabilized beta-gamma TiAl alloys without single α-phase field. Unlike the α + γ two-phased TiAl or beta-gamma TiAl with single α-phase field, the wrought multi-phase TiAl–4/6Nb–2Mo–B/Y alloys exhibit special annealing process to obtain FL microstructure. Short-term annealing at temperatures slightly above β-transus is recommended to produce the desired FL microstructure. The related mechanism is to guarantee the sufficient diffusion homogenization of β stabilizers during single β-phase annealing, and further avoid α decomposition by α → γ + β when cooling through α + β + γ phase field. The colony boundary β phase contributes to fine-grained nearly FL microstructure, by retarding the coarsening of the α phase grains.     

Assessment of spray quality from an external mix nozzle and its impact on SQL grinding performance

Spray quality is the critical factor which decides the efficacy of Small Quantity Lubrication (SQL) technology in a high specific energy involved machining process like grinding. Yet, the understanding about spray quality, the actual process mechanics and its effect on machining performance is inadequate. The present work is an attempt to establish a correlation between the spray input variables, quality of the spray and machining performance of SQL grinding through modelling and experiments. Using computational fluid dynamic techniques, the variation of droplet size, droplet velocity, number of droplets and heat transfer coefficient have been analysed at different input parameters and the computed trends have been verified and validated. CFD modelling of spray indicates that it is possible to produce aerosol medium with high heat dissipation ability at moderately high air pressure and low flow rate. It also shows that any increase in atomising air pressure favourably leads to notable increase in wetting area and also results in substantial enhancement in heat dissipation ability. Reduction of residual stress is thus remarkably good. On the other hand, grinding fluid flow rate, if increased, offers significantly better lubricity and reduces the grinding force which also reduces tensile residual stress. Short spell grinding test results are found to be in good agreement with CFD results.     

Reducing numerical dissipation in smoke simulation

Numerical dissipation acts as artificial viscosity to make smoke viscous. Reducing numerical dissipation is able to recover visual details smeared out by the numerical dissipation. Great efforts have been devoted to suppress the numerical dissipation in smoke simulation in the past few years. In this paper we investigate methods of combating the numerical dissipation. We describe visual consequences of the numerical dissipation and explore sources that introduce the numerical dissipation into course of smoke simulation. Methods are investigated from various aspects including grid variation, high-order advection, sub-grid compensation, invariant conservation, and particle-based improvement, followed by discussion and comparison in terms of visual quality, computational overhead, ease of implementation, adaptivity, and scalability, which leads to their different applicability to various application scenarios.     

The Clausius inequality corrected for heat transfer involving radiation

The objective of this paper is to prove that the Clausius inequality must be re-stated to have general applicability for heat transfer involving radiative fluxes. The integrand (đQ/T) of the Clausius expression applies to heat conduction and convection, but does not hold for most radiative transfer scenarios, with the exception of reversible infinitesimal net blackbody radiation transfer. In other cases involving radiative transfer, the equality holds for a cycle even though irreversible heat addition by radiative transfer occurs. This is without the erroneous presumption of entropy destruction anywhere in the cycle. Thus, the Clausius inequality indicates reversibility for a cycle that includes an irreversible process. Further, in some radiative cases the quantity đQ/T, where T is the boundary temperature, is not the entropy transfer at the system boundary, and in fact, primarily represents entropy production within the system. It is also clear that in another case considered, the quantity đQ/T had no physical meaning whatsoever. Consequently, the Clausius expression has been re-stated so that it is applicable to cycles with processes involving any form of heat transfer. A new integrand (đQ_cc/T + đS_Net,Rad) is presented, allowing the Clausius inequality to generally apply to all heat transfer scenarios. The work in this paper emphasizes the need to re-state other fundamental equations allowing applicability to all heat transfer processes, and draws attention to the unique character of radiative entropy calculations.     

Cooling and Solidification of Melted Drops in an Immiscible Cooling Medium

The cooling and solidification of melted drops during their movement in an immiscible cooling medium is widely employed for granulation in the chemical industry, and a study of these processes to provides a basis for the design of the granulation tower height and the temperature of the cooling medium is reported. A physical model of the cooling and solidification of the drop is established and the numerical calculation is performed. The influences of the key factors in the solidification, i.e., Bi number, drop diameter, temperature of the cooling medium, etc. are presented. The cooling and solidification during wax granulation in a water‐cooling tower and during urea granulation in an air‐cooling tower (spraying tower) are described in detail. Characteristics of the solidification and temperature distribution within the particle at different times are shown. The model and calculations can be used for structure design of the granulation tower and optimization of the operation parameters.     

Thermal-lens and photo-acoustic methods for the determination of SiC thermal properties

In this paper we report the use of photothermal techniques such as Thermal lens (TL) spectrometry, Photoacoustic and heat capacity, ρc_p, to determine the thermo-optical parameters, such as thermal conductivity (K), thermal diffusivity (D), specific heat (c_p) and the optical path dependence with temperature (ds/dT), of an undoped polycrystalline 3C-SiC. To our knowledge, this is the first time that Thermal lens technique is used for wide band-gap systems. Results obtained for the polycrystalline sample with TL technique indicates that ds/dT is negative at room temperature. Moreover, the obtained values of thermal diffusivity and thermal conductivity are in good agreement with that found in the literature, indicating that the phototermal techniques can be used to obtain the referred parameters in circumstances where other techniques cannot be used, for example, in harsh environments.     

Heat Transfer Analysis for Gas-to-Liquids Transportation Through Trans Alaska Pipeline

Gas-to-liquids (GTL) technology involves the conversion of natural gas to liquid hydrocarbons. In this article, theoretical studies have been presented to determine the feasibility of transporting GTL products through the Trans-Alaska Pipeline System (TAPS). To successfully transport GTL through TAPS, heat loss along the route must be carefully determined. This study presents heat transfer and fluid dynamic calculations to evaluate this feasibility. Because of heat loss, the fluid temperature decreases in the direction of flow and this affects the fluid properties, which in turn influence convection coefficient and pumping power requirements. The temperature and heat loss distribution along the pipeline at different locations have been calculated. Fairly good agreement with measured oil temperatures is observed. The powers required to pump crude oil and GTL individually, against various losses have been calculated. Two GTL transportation modes have been considered; one as a pure stream of GTL and the second as a commingled mixture with crude oil. These results show that the pumping power and heat loss for GTL are less than that of the crude oil for the same volumetric flow rate. Therefore, GTL can be transported through TAPS using existing equipment at pump stations.     

Analysis of Multiphase Flow and Heat Transfer: Pressure Buildup in an Unsaturated Porous Slab Exposed to Hot Gas

This study develops a mathematical model for coupled heat and mass transfer in an unsaturated porous slab exposed to a flowing hot gas. Effects of the initial saturation conditions on associated variables, i.e., total pressure, temperature, moisture content, and multiphase flow, are studied. The Newton-Raphson method based on a finite volume technique is applied. This study emphasizes the influence of initial saturation level and gravitational effect in heat and multiphase flow phenomena associated with this system. Gravity enhances the downward flow of liquid within the porous slab. Pressure buildup occurs near the interface between the wet and the dry zone. However, it appears that the order of magnitude to the total pressure is small. This study explains the fundamental mechanism of multiphase flow that involves heat and mass transfer in a heated unsaturated porous slab.