电路电磁兼容建模与仿真

提出了对暴露在任意外场中的传输线进行时频分析的新方法，这种方法非常稳定，它能够与任意的传输线模型和电路仿真方法兼容，并且使用这种方法得到的仿真值和实际值之间的差别小于1％。     

一种新型注入剖面组合测井仪及其应用

为了提高注入剖面测井的准确性，研制了一种新型注入剖面组合测井仪。该仪器由流量处理单元、伽马处理单元、井温处理单元、磁性定位处理单元、调制式传输、电源电路六部分组成。一次下井可同时测取流量、伽马、井温、磁性定位四组参数。具有测取资料精度高、单芯电缆传输、流量可单点测量也可连续测量以厦现场监测和维修方便等特点。     

可控震源施工中电台数据传输不良的原因分析及排除

可控震源在施工中,常常出现各种电台干扰,导致震源数据传输不正常或震源收不到仪器发出的遥控启动信号,影响正常施工.本文介绍了各种电台干扰引起的故障现象,分析了故障产生的原因,给出了故障的排除方法.     

Mechanical spectroscopy in commercial Fe–6 wt.% Si alloys between 400 and 1000 K

Mechanical spectroscopy, neutron diffraction and differential scanning calorimetry (DSC) were performed on commercial Fe–6 wt.% Si alloy after quenching from high temperature. The damping spectrum shows a peak at around 800 K and an associated modulus defect. The modulus shows an increase during the second and subsequent heating runs. In addition, an anomaly in the modulus behavior has been found at around 400 K. Different thermal treatments allows to obtain two different recovery degrees of the quenched-in defects. The influence of the recovery degree on the 800 K internal friction peak and on the anelastic modulus has been evaluated and confirm the validity of the grain boundary mechanism associated to this peak. Experimental results are discussed on the basis of recovery and ordering processes.     

Chemische Zusammensetzung und Mikrostruktur polymerabgeleiteter Gläser und Keramiken im System Si–C–O. Teil 2: Charakterisierung der Gefügeausbildung mittels hochauflösender Durchstrahlungselektronenmikroskopie und Feinbereichsbeugung

Chemical Composition and Microstructure of Polymer‐Derived Glasses and Ceramics in the Si–C–O System. Part 2: Characterization of microstructure formation by means of high‐resolution transmission electron microscopy and selected area diffraction Liquid or solid silicone resins represent the economically most interesting class of organic precursors for the pyrolytic production of glass and ceramics materials on silicon basis. As dense, dimensionally stable components can be cost‐effectively achieved by admixing reactive filler powders, chemical composition and microstructure development of the polymer‐derived residues must be exactly known during thermal decomposition. Thus, in the present work, glasses and ceramics produced by pyrolysis of the model precursor polymethylsiloxane at temperatures from 525 to 1550 °C are investigated. In part 1, by means of analytical electron microscopy, the bonding state of silicon was determined on a nanometre scale and the phase separation of the metastable Si–C–O matrix into SiO₂, C and SiC was proved. The in‐situ crystallization could be considerably accelerated by adding fine‐grained powder of inert fillers, such as Al₂O₃ or SiC, which permits effective process control. In part 2, the microstructure is characterized by high‐resolution transmission electron microscopy and selected area diffraction. Turbostratic carbon and cubic β‐SiC precipitate as crystallization products. Theses phases are embedded in an amorphous matrix. Inert fillers reduce the crystallization temperature by several hundred °C. In this case, the polymer‐derived Si–C–O material acts as a binding agent between the powder particles. Reaction layer formation does not occur. On the investigated pyrolysis conditions, no crystallization of SiO₂ was observed.     

光纤通信在市内接入网的应用

先说明市内接入网的单位用户和住家用户两大类使用通信和电视、交互型和分配型业务的要求不相同，相应地对光纤传输的应用须作不同的考虑，文中认为；光纤从市内交换局直连办公大楼是合乎现实需要的，而对于居民住家，宜选用光纤连至路边或光纤与同轴结合和适当利用无源光网络等方案，俟将来时机成熟才实行光纤连至每一家，文末有概括总结，说明接入网不同于长途网，接入网的光纤系统可以使用常规单模光纤，工作于波长1．3μm，而光放大器和波分多路系统不是普遍需要，但光电子集成在光端机中是必要的。     

井场信息系统建设体系结构

对井场钻井数据实时远程传输的研究和实践进行了总结,从数据远传作用、数据远传通信方式、数据通信网络体系结构、未来发展等几个方面对井场数据远程传输进行了探讨。     

高速往复式内燃机平衡轴低质量设计分析

分析了扇形和偏心圆两种平衡轴设计的要求以及平衡重低质量的设计原则。扇形平衡重半径及宽度应尽量大、夹角应尽量小。偏心圆平衡重的偏心圆半径应尽可能大 ,轴承半径应尽可能小。同样质量的扇形平衡重产生的平衡力比偏心圆平衡重要大。     

有耗传输线的TLM模型法

本文从传输线理论出发，介绍了一种解决传输线问题的新方法－－TLM法。     

编码解码芯片HD3-6408-9及其应用

编码解码芯片HD3 64 0 8 9是一种高性能的CMOS器件。这种大规模芯片主要由编码器和解码器两部分组成。在数据传输应用中 ,采用两个独立的单片机系统 ,利用编码解码芯片 (HD3 64 0 8 9)组成数字信号的接收、发送及显示部分来完成数据传输功能