New nanocomposite based on poly(lactic-co-glycolic acid) copolymer and magnetite. Synthesis and characterization

The study presents the preparation of the new magnetic nanocomposite based on PLGA and magnetite. The PLGA used to obtain the magnetic nanocomposites was synthesized by the copolymerization of lactic acid with glycolic acid, in the presence of tin octanoate [Sn(Oct)₂] as catalyst, by polycondensation procedure. Magnetite was obtained by co-precipitation from aqueous salt solutions FeCl₂/FeCl₃. The particles size of magnetite was 420 nm, and the saturation magnetization 62.78 emu/g, while the PLGA/magnetite nanocomposite size was 864 nm and the saturation magnetization 39.44 emu/g. The magnetic nanocomposites were characterized by FT-IR, DLS technique, SEM, VSM and simultaneous thermal analyses (TG–FTIR–MS). The polymer matrix PLGA acts as a shell and carrier for the active component, while magnetite is the component which makes targeting possible by external magnetic field manipulation. Based on the gases resulted by thermal degradation of PLGA copolymer, using the simultaneous analysis TG–FTIR–MS, a possible degradation mechanism was proposed.     

Electromagnetic shielding properties of iron oxide impregnated kenaf bast fiberboard

The electromagnetic shielding effectiveness of kenaf fiber based composites with different iron oxide impregnation levels was investigated. The kenaf fibers were retted for removing the lignin and extractives from the fibers and magnetized. Using the unsaturated polyester and the magnetized fibers, kenaf fiber based composites were manufactured by the compression molding process. The transmission energies of the composites were characterized when the composite samples were exposed under the irradiation of electromagnetic (EM) wave with a variable frequency from 9 GHz to 11 GHz. Using the Scanning Electron Microscope (SEM), the iron oxide nanoparticles were observed on the surfaces and inside the micropore structures of single fibers. As the Fe content increased from 0% to 6.8%, 15.9% and 18.0%, the total surface free energy of kenaf fibers with the magnetizing treatments increased from 44.8 mJ/m² to 46.1 mJ/m², 48.8 mJ/m² and 53.0 mJ/m², respectively, while the modulus of elasticity reduced from 2875 MPa to 2729 MPa, 2487 MPa and 2007 MPa, respectively. Meanwhile, the shielding effectiveness was increased from 30–50% to 60–70%, 65–75% and 70–80%, respectively.     

Synthesis and characterization of nanostructured magnetoresistive Ni doped ZnO films

We report a method to produce magnetic nanostructured semiconductor films based in ZnO doped with Nickel to control their magnetic properties. The method is based on a combined diffusion–oxidation process within a controlled atmosphere chamber to produce a uniform distribution of Ni ions in the ZnO films (ZnO:Ni). The synthesis of ZnO:Ni films is reported as well as the magnetoresistive characteristics, the used method yields films with reproducible and homogeneous properties. The films were also characterized structurally by X-Ray Diffraction (XRD) and Raman spectroscopy, and by Hall–van der Pauw measurements. The XRD measurements confirm the nanocrystalline films character. The films resulted of n-type conductivity with electron concentrations of ~10²⁰ cm⁻³ in average and carrier mobilities of 5 cm²/V s. The Magnetoresistance (MR) behavior of the films at 300 K shows negative changes of ΔR~0.5% in accordance with the usual literature reports on samples produced by other methods.     

Influences of magnetic fields on current–voltage characteristics of gold-DNA-gold structure with variable gaps

Achieving highly sensitive magnetic sensors by means of Metal-DNA-Metal (MDM) structure is a key issue. DNA, being a genetic information carrier in living cells reveals tunable semiconducting response in the presence of external electric and magnetic fields, which is promising for molecular electronics. The influence of magnetic fields up to 1200 mT on the current–voltage (I–V) behavior of Gold-DNA-Gold (GDG) structure having variable gap sizes from 20–50 μm are reported in this work. These structures were fabricated using UV lithography, DC magnetron sputtering and thermal evaporation techniques. DNA strands were extracted from Boesenbergia rotunda plant via standard protocol. The acquired I–V characteristics display the semiconducting diode nature of DNA in GDG structures. The potential barrier for all the structures exhibit an increasing trend with the increase of externally imposed magnetic field irrespective of variable gap sizes. Furthermore, the potential barrier in GDG junction at higher magnetic field strengths (>1000 mT) is found to be considerably enhanced. This enhancement in the junction barrier height at elevated magnetic fields is attributed to the reduction of carrier mobility and augmentation of resistance. The achieved admirable features of magnetic sensitivity suggest the viability of using these GDG sandwiches as a prospective magnetic sensor.     

Chemical leaching and magnetic properties of non-equilibrium Al(Co–Cu) powders produced by rod milling

We report upon the chemical leaching and magnetic properties of nanoscale crystalline Al_0.6(Co₂₅Cu₇₅)_0.4 alloy powders produced by rod milling. X-Ray diffractometry (XRD), transmission electron microscopy, differential scanning calorimetry, vibrating sample magnetometry, and superconducting quantum interference device magnetometry were used to characterize the as-milled and leached specimens. After 400 h of milling, only the b.c.c. phase of the intermetallic compound γ-Al_3.892Cu_6.10808 was detected by XRD. After annealing the leached specimen at 600 °C for 1 h, the nanoscale crystalline phase was transformed into the f.c.c. Cu phase, and this was accompanied by a change in the magnetic properties. The peaks of the magnetization shifted towards lower temperature with increasing external field. The temperature behavior at T_f (45 K) for direct current (d.c.) magnetic susceptibility measurements was quite different for field cooling and zero-field cooling. After cooling the leached specimen from 800 °C, magnetization increased gradually.     

Cif2000平台下的核磁共振测井解谱方法研究

介绍了在Cif2000多井解释平台下的核磁共振解谱方法与编程实现。解谱采用加入平滑因子后在特征矩阵的奇异值分解中截去小的非零奇异值的方法，可以在低信噪比时得到稳定的弛豫谱，在油田实际应用中证明了该方法的有效性。根据该方法在Cif2000平台上编制了完整的解谱处理程序，可以直接用于油田的生产实际。     

Influence of accelerated ageing on methacrylate‐based denture resins heterogeneity as viewed by ESR‐spin‐probe method

The electron‐spin‐resonance (ESR) spin‐probe method, was used to study the heterogeneity of denture resins based on poly(methyl methacrylate). Results for three resins processed by microwave energy, conventional curing and cold curing (depending on the curing procedure and exposed to ageing in various environmental conditions) were compared. All three cured resins were stored over the same time (1200 h) in distilled water at ambient temperature and in artificial saliva at 348 K. The temperature‐dependent ESR spectra of a spin probe dispersed in the denture resins are analyzed in terms of line‐shapes and line‐widths. The appearance of two spectral components was taken as an indication of resin heterogeneity. The results reveal that the cold‐cured resin has a lower local density in comparison with microwave and conventionally cured resin. The amount of residual monomer also contributes to the local motion of polymer segments. The change of denture resins exposed to ageing is influenced both by the structure of the original resin and the ageing conditions. Restricted motion of a spin probe incorporated into the acrylic resins exposed to accelerated ageing suggests additional crosslinking of polymer chains. The differences are observed for all the investigated resins, but the highest change is observed with the cold‐cured resin. The ESR results are accompanied by T_g and T_m measurements. Copyright © 2005 Society of Chemical Industry     

天津独流减河工程监控系统现地通信单元设计

提出一种配电网电容电流测量的新方法，在零序电压互感器的开口三角侧串联一个可调电感，通过注入一个变频恒流信号寻找配电网的谐振频率，改变可调电感的数值后寻找另一谐振频率，联立2个谐振方程求解电容电流，该方法消除了电压互感器漏抗对测量的影响。开发了配电网电容电流测量仪，经模拟试验和现场测试表明，该方法具有安全、快捷、准确等特点，适用于中性点不接地或经随调式消弧线圈接地配电网。     

基于复数主成分分析的磁共振波谱信号衰减系数的自动校正

衰减系数的校正是磁共振波谱信号处理和分析过程中的一个关键难题。本文基于复数主成分分析，提出了一种自动的磁共振波谱衰减系数的校正方法，较成功地解决了这个难点问题。文中的模拟数据及其实现结果充分验证了该方法的有效性。     

Schwingfestigkeit von Schraube‐Mutter‐Verbindungen

High cycle fatigue of bolted connections Extensive tests regarding the influences on the fatigue of bolt‐nut‐connections of preloading with torsion, of preloading with yielding, of loading with superimposed bending and of the tested lot are processed. These influences are not yet known according to VDI 2230. New testing devices were designed for these tests, which allow a far less expensive operation and may easily be used for bolts of diameters up to M100 and testing frequencies up to 1000 Hz. The validity of fatigue resistance according to VDI 2230 is specified with respect to the test results. The determined influence of the tested lots is unexpectedly high. The manufacturing process of bolts should be improved to minimize this influence.