Comparative analysis of formaldehyde and toluene sorption on indoor floorings and consequence on Indoor Air Quality

Indoor surfaces may be adsorptive sinks with the potential to change Indoor Air Quality. To estimate this effect, the sorption parameters of formaldehyde and toluene were assessed on five floorings by an experimental method using solid-phase microextraction in an airtight emission cell. Adsorption rate constants ranged from 0.003 to 0.075 m·h⁻¹, desorption rate constants from 0.019 to 0.51 h⁻¹, and the partition coefficient from 0.005 to 3.9 m, and these parameters vary greatly from one volatile organic compound/material couple to another indicating contrasted sorption behaviors. A rubber was identified as a sink of formaldehyde characterized by a very low desorption constant close to 0. For these sorbent floorings identified, the adsorption rates of formaldehyde are from 2 to 4 times higher than those of toluene. Two models were used to evaluate the sink effects of floorings on indoor pollutant concentrations in one room from different realistic conditions. The scenarios tested came to the conclusion that the formaldehyde sorption on one rubber (identified as a sink) has a maximum contribution from 15% to 21% for the conditions of low air exchange rate. For other floorings, the sorption has a minor contribution less than or equal to 5%, regardless of the air exchange rate.     

ATSP:时态网络可视化的自适应时间片划分方法

现有的时态网络可视化方法大多采用等量时间片来可视化网络的演变，不利于时态模式的快速挖掘和发现。为此，根据时态网络固有的特征提出自适应时间片划分方法（Adaptive Time Slice Partition method，ATSP）。在时态网络的两种表示方式（基于事件的表示方式和基于快照的表示方式）的基础上，构建了ATSP的基础模型，同时提出了一种改进模型用来描述事件间隔时间服从长尾分布的时态网络。为了实现时间片的不等量划分，针对探索任务的不同提出了基于时态模式的ATSP规则和基于中心节点的ATSP规则，并提出了实现算法--层次划分算法（Hierarchical Partition algorithm，HP）和增量划分算法（Incremental Partition algorithm，IP）。实验结果表明，ATSP方法比传统的时间片划分方法更能准确地表示网络的时态特征，且该方法应用于可视化时，能有效归纳并展示网络的特征，明显提高了视觉分析的效率。     

双级染料激光放大器泵浦能量分配的数值研究

用染料激光放大器的横向稳态泵浦理论，对不同的入射光能量选择不同的增益计算方法，研究了双级染料放大器的泵浦能量分配比例、泵浦光总能量和信号光能量大小对激光增益的影响。计算结果表明，对于其他参数确定的放大系统，存在着最佳的泵浦能量分配比例，可获得最大增益输出。通过自编程序的计算，可方便地找出特定系统泵浦能量分配比例的最佳值。     

An algorithm for architecture partitioning in high-speed networks with bursty traffic

This paper analyzes the performance of a switching architecture. The performance measures include the elapsed time of packet transfer and the waiting time to begin transfer. The architecture is partitioned depending on the type of network used and the expected traffic in the network. Every partition has a switch with a buffer that can absorb surges of bursty traffic within the network partition. The buffer size depends on the type of the network and incoming traffic. The partition size depends on the network bandwidth, network traffic, packet size and buffer size. Examples of different networks are used to show the applications of the model. The results show that the elapsed time of packet switch transfer depends exponentially on the number of partitions in the network.     

基于虚拟分割机制的多服务交换路由器的研究

本文提出了一处基于虚拟分割机制的可编程多服务器由器实现结构：PVSMR，并对它的三个层面的主要构成及其关键技术进行了深入研究。PVSMR基于一种有效而灵活的资源虚拟分割算法，它能够提供与多类应用相适应的、灵活的报文处理和转发控制能力。     

CRC计算方法的研究

本文丛面地介绍了ＣＲＣ的基本原理和计算方法，并给出了编程实例。     

提高曲面近似展开精度的方法与实现

通过对不可展曲面近似展开精度的研究，提出了根据曲面曲率的大小对曲面自动进行网格划分，通过对综合展开误差数据场进行数据拟合来选取最优展开基点，基于空间曲面与其展开图间近似的等距变换关系进行展开样形的误差矫正等3种方法，这几种方法的实现在不同程度上有效地减小了曲面的近似展开误差，提高了曲面的近似展开精度。     

穿壁焊极柱合金探索

本文对起动用铅酸蓄电池穿壁焊极柱用合金配方进行了探索 ,并得到了良好的应用效果     

Transient operation of a catalytic liquid-liquid plug flow reactor for kinetics measurements

A centrifugal partition chromatograph (CPC) was used as a liquid-liquid catalytic reactor for the isomerisation of hexen-3-ol into ethylpropylketone with a water soluble rhodium catalyst. Global mass transfer coefficients were measured and shown to depend on both the nature of the solute and the flow rate. Liquid-liquid partition isotherms were also determined with the CPC using elution chromatography. Finally, a reactor model was derived to account for the experimental results obtained both under stationary and transient (pulse) conditions. A parameter sensitivity evaluation is also presented.     

An environment for prototyping distributed applications

Designing a distributed application is an extremely complex task. Proper facilities for prototyping distributed applications can be useful in evaluating a design, and also in understanding the effect of different parameters on the performance of an application. We describe a language for prototyping distributed applications, that supports different communication primitives with specified delay, and provides primitives to aid debugging and evaluation. Our environment for executing distributed programs supports heterogeneous computation in which processes can execute on different hardware. Different source languages can be used for coding different modules of the processes. The system has a centralized control and monitoring facility which is based on the Suntools window system.