Studies on influence of hydrogen and carbon monoxide concentration on reduction progression behavior of molybdenum oxide catalyst

Temperature programmed reduction (TPR) analysis was applied to investigate the chemical reduction progression behavior of molybdenum oxide (MoO₃) catalyst. The composition and morphology of the reduced phases were characterized by X-ray diffraction spectroscopy (XRD), X-ray photoelectron spectroscopy (XPS), and field emission scanning electron microscopy (FE-SEM). The reduction progression of MoO₃ catalyst was attained with different reductant types and concentration (10% H₂/N₂, 10% and 20% CO/N₂ (%, v/v)). Two different modes of reduction process were applied. The first approach of reduction involved non-isothermal mode reduction up to 700 °C, while the second approach of reduction involved the isothermal mode reduction for 60 min at 700 °C. Hydrogen temperature programmed reduction (H₂-TPR) results showed the reduction progression of three-stage reduction of MoO₃ (Mo⁶⁺ → Mo⁵⁺ → Mo⁴⁺ → Mo⁰) with Mo⁵⁺ and Mo⁴⁺. XRD analysis confirmed the formation of Mo₄O₁₁ phase as an intermediate phase followed by MoO₂ phase. After 60 min of isothermal reduction, peaks of metallic molybdenum (Mo) appeared. Whereas, FESEM analysis showed porous crater-like structure on the surface cracks of MoO₂ layer which led to the growth of Mo phase. Meanwhile, the reduction of MoO₃ catalyst in 10% carbon monoxide (CO) showed the formation of unstable intermediate phase of Mo₉O₂₆ at the early stage of reduction. Furthermore, by increasing 20% CO led to the carburization of MoO₂ phase, resulted in the formation of Mo₂C rather than the formation of metallic Mo, as confirmed by XPS analysis. Therefore, the presented study shows that hydrogen gave better reducibility due to smaller molecular size, which contributed to high diffusion rate and achieved deeper penetration into the MoO₃ catalyst compared to carbon monoxide reductant. Hence, the reduction of MoO₃ in carbon monoxide atmosphere promoted the formation of Mo₂C which was in agreement with the thermodynamic assessment.     

Size-controlled synthesis of Mo powders via hydrogen reduction of MoO2 powders with the assistance of Mo nuclei

The size-controlled preparation of Mo powders is always a challenge and important task in the molybdenum metallurgy. In the current study, Mo powders with controllable sizes are synthesized by hydrogen reduction of MoO₂ powders with the assistance of Mo nuclei in the range of 900–1100 °C. The influences of the particle sizes of Mo nuclei, the additive amount as well as reaction temperature on the morphology and particle sizes of the final products are studied. For the hydrogen reduction of MoO₂ without any additive, the obtained Mo powders always have large particle sizes. However, the addition of small amounts of nuclei in MoO₂ can help Mo nucleate dispersedly, and the growth of Mo could be also controlled by adjusting the sizes of added nuclei, amount of addition and the reaction temperature. With the addition of Mo nuclei, the different sizes of Mo powders with the good dispersity can be prepared. As adding commercial Mo powders with the particle size of about 2.03 μm, the micron-sized Mo powders ranged from 2.11 μm to 3.25 μm could be prepared. While for the case of adding ultrafine Mo nuclei of about 170 nm, Mo powders from 0.28 μm to 0.88 μm can be obtained. Moreover, the more the amounts of nuclei added and the lower the reaction temperature (in the range of 900–1100 °C) is, the smaller the particle size of the prepared Mo powder will be. The current method is a facile and feasible method, and is potential to be used for industrial production of Mo powder with controllable particle sizes.     

Behaviour of Surface Defects in Wire Rod Rolling

Defects are often present in rolled products, such as wire rod. The market demand for wire rod without any defects has increased. In the final wire rod products, defects originating from steel making, casting, pre‐rolling of billets and during wire rod rolling can appear. In this work, artificial V‐shaped longitudinal surface cracks have been analysed experimentally and by means of FEM. The results indicate that the experiments and FEM calculations show the same tendency except in two cases, where instability due to fairly “round” false round bars disturbed the experiment. FE studies in combination with practical experiments are necessary in order to understand the behaviour of the material flows in the groove and to explain whether the crack will open up as a V‐shape or if it will be closed as an I‐shape.     

钻井钢丝绳检测方法与装置的研究

钻井钢丝绳对于钻井平台安全可靠性有直接影响。采用磁性检测方法对钻井钢丝绳进行检测,并对钻井钢丝绳的励磁方式、聚磁方法及传感器与钢丝绳的配合间隙问题进行分析。在此基础上,研制了钻井钢丝绳检测仪器,能够实现对钻井钢丝绳断丝、磨损等缺陷的定性、定量检测,并能够对缺陷进行定位,为钻井钢丝绳的寿命评估提供了依据,对提高钻井平台的安全性具有重要意义。     

FZ-870绕线机排线机构电控系统分析

文章分析了FZ-870绕线机排线机构电控系统，并就存在的问题提出了对策。     

丝网气液分离器分离性能和压力损失分析

对丝网气液分离器的分离机理进行了详细分析,在此基础上给出了丝网气液分离器的分离效率和压降计算公式。与HG/T 21618-1998《丝网除沫器》中的公式相比,此公式可以用于任意组合的丝网结构,更具普适性,并且能定量分析各种分离机理对分离的贡献。对丝网式空气过滤器计算的结果表明,此公式具有很好的精度,可以用于工程设计。     

Improving Short-Circuit Current Capacity, Resistance, and Breaking Load of OPGW Constructions by Modifying Aluminium Alloy With AlB2

This article presents a method that can be applied to molten AA-6101 alloy to improve electrical properties of the aluminium part of the optical ground wire (OPGW) used in overhead transmission lines to protect phase conductors from lightning strike and to transmit signals and data. AA-6101 alloy in casting of the log as 6 m length and 178 mm diameter for extrusion has been inoculated by AlB₂ to decrease detrimental effects of Cr, Ti, V, and Zr on the conductivity of the material. After inoculation, improved billets were extruded as 9.5 mm diameter feedstock. Required wires drawn from the feedstock according to the construction types of OPGW to be tested were exposed to aging at 175°C, 6 h (T-8). Upon completion of the back-twist and performing-type stranding process, resistance, and short-circuit current capacity and breaking load of the OPGW 88/44 constructions with other metal combinations have been examined and tested to show improvement. Results are summarized in tables and graphically.     

加强民用电管理的技术措施

提出并实施了住宅楼集中计量配电系统，为加强民用电管理提供了技术措施。     

吐丝圈径对大规格高碳盘条组织性能的影响

计算与分析了斯太尔摩冷线上盘条的吐丝圈径、搭接密度及"佳灵"装置横向布风曲线之间的关系,研究了吐丝圈径的大小对大规格82B盘条组织和性能的影响,确定了大规格82B盘条最小吐丝圈径应为980mm.     

浅析6063铝型材表面“铝丝印”的成因与对策

在介绍“铝丝印”概念的基础上，从金属腐蚀学的观点出发，分析了“铝丝印”形成的电化学腐蚀机理，并提出了具体的解决措施。