Mechanical properties,corrosion resistance,and rubber pad forming of cold differential speed-rolled pure titanium for bipolar plates of proton-exchange membrane fuel cells

Due to problems such as pores on surface-treated coatings, the corrosion resistance of pure titanium bipolar plates for proton-exchange membrane fuel cells can be further improved by increasing the corrosion resistance of pure titanium by using differential speed-rolling (DSR); however, these materials have not yet reached the standard requirements of bipolar plates (corrosion current density i_corr＜10³ nA·cm^?2). In this work, the corrosion resistance of pure titanium was improved by optimizing the DSR process while the strength was maintained. The best corrosion resistance of the DSR pure titanium was achieved when the roller speed ratio was 2, while i_corr was 429 nA·cm^?2 in a solution of 0.5 M H₂SO₄ and 2 mg/L HF at room temperature. The formability of the DSR pure titanium for bipolar plates was verified. The optimal holding pressure range was 6.8–7.0 kN.     

Nonlinear response in glass fibre non-crimp fabric reinforced vinylester composites

This paper addresses the nonlinear stress-strain response in glass fibre non-crimp fabric reinforced vinylester composite laminates subjected to in-plane tensile loading. The nonlinearity is shown to be a combination of brittle and plastic failure. It is argued that the shift from plastic to brittle behaviour in the vinylester is caused by the state of stress triaxiality caused by the interaction between fibre and vinylester. A model combining damage and plasticity is calibrated and evaluated using data from extensive experimental testing. The onset of damage is predicted using the Puck failure criterion, and the evolution of damage is calibrated from the observed softening in plies loaded in transverse tension. Shear loading beyond linear elastic response is observed to result in irreversible strains. A yield criterion is implemented for shear deformation. A strain hardening law is fitted to the stress-strain response observed in shear loaded plies. Experimental results from a selection of laminates with different layups are used to verify the numerical models. A complete set of model parameters for predicting elastic behaviour, strength and post failure softening is presented for glass fibre non-crimped fabric reinforced vinylester. The predicted behaviour from using these model parameters are shown to be in good agreement with experimental results.     

[Zr0.73(Cu0.59Ni0.41)0.27]87Al13合金过冷液相区热塑性成形研究

为探究[Zr_(0.73)(Cu_(0.59)Ni_(0.41))_(0.27)]_(87)Al_(13)非晶合金的热塑性成形性能以及绘制其对应的热加工图谱,用Gleeble3500型热模拟压缩实验机对该非晶合金进行不同参数下的热模拟压缩实验。结果表明,合金在压缩过程中变形行为由牛顿流变演变为非牛顿流变;同时,过高或过低的热加工温度均能导致合金晶化;进一步对数据分析得到该合金在不同热塑性成形参数下的功率耗散图与流变失稳图,并绘制出相应的热加工谱图,谱图分析结果表明,该合金在温度为420与430℃、应变速率为10~(-3) s~(-1)时具有较高功率耗散系数且没有失稳区域,因此,合金可选的热塑性加工参数为温度420～430℃,应变速率10~(-3) s~(-1)。     

Densification mechanism during reactive hot pressing of B4C-ZrO2 mixtures

The densification behaviors of pure B₄C and B₄C-ZrO₂ mixtures were compared during hot pressing. The results showed that in-situ formed ZrB₂ effectively enhanced the densification process of B₄C-ZrO₂ mixtures, more significantly during the intermediate stage. Within the relative density ranging from 0.75 to 0.90, the B₄C-15?wt%ZrO₂ mixture (B15Z) achieved the maximum densification rate as twice much as that of pure B₄C. The stress exponent n>3 indicated plastic deformation was the dominant densification mechanism of B15Z. The viscosities of plastic flow were evaluated using Murray-Rodger-William equation and the viscosity of B15Z was only a quarter of that in pure B₄C. The sintering activation energy was calculated to be 305.9?kJ/mol for pure B₄C and 197?kJ/mol for B15Z, respectively. It was proposed that the lower viscosity of plastic flow and activation energy accelerated the sliding and propagating motions of plastic flow, by which underlain the enhanced densification behaviors of B₄C-ZrO₂ mixtures.     

An efficient manufacturing method for I-shaped cross-sectional CFRP beam with arbitrary arrangement of carbon fiber using electro-activated resin molding

Abstract

The I-shaped cross-sectional beam of CFRP (CFRP I-beam) is usually manufactured by the continuous protrusion method. Carbon fibers can only be arranged in the longitudinal direction. The CFRP I-beam with arbitrary arrangement of carbon fiber was manufactured with applying the electro-activated deposition molding method. The carbon fiber fabric was immersed in the deposition solution and energized, epoxy resin precipitated around carbon fiber and impregnated. The resin-impregnated fabric was installed to the mold, and the CFRP I-beam was fabricated. The CFRP I-beam was subjected to three-point bending tests, and the relationship between load-deflection was simulated by finite-element analysis.     

Effect of grinding-induced cyclic heating on the hardened layer generation in the plunge grinding of a cylindrical component

This paper discusses the effects of the grinding-induced cyclic heating on the properties of the hardened layer in a plunge cylindrical grinding process on the high strength steel EN26. It was found that a multi-pass grinding brings about a uniform and continuous hardened layer along the circumference of the cylindrical workpiece. An increase of the number of grinding passes, leads to a thicker layer of hardening, a larger compressive residual stress and a deeper plastic deformation zone. Within the plastic deformation zone, the martensitic grains are refined by the thermo-mechanical loading, giving rise to a hardness of 12.5% higher than that from a conventional martensitic transformation. The coupled effects of heat accumulation and wheel wear in the multi-pass grinding are the main causes for the thickening of the hardened layer. A too small infeed per workpiece revolution would result in insufficient grinding heat, and in turn, bring about an undesirable tempered hardened layer and a reduction of its hardness.     

Bulging in incremental sheet forming of cold bonded multi-layered Cu clad sheet: Influence of forming conditions and bending

Bulge is a defect that causes geometrical inaccuracy and premature failure in the innovative incremental sheet forming (ISF) process. This study has two-fold objectives: (1) knowing the bulging behavior of a Cu clad tri-layered steel sheet as a function of forming conditions, and (2) analyzing the bending effect on bulging in an attempt to identify the associated mechanism. A series of ISF tests and bending analysis are performed to realize these objectives. From the cause-effect analysis, it is found that bulge formation in the layered sheet is sensitive to forming conditions in a way that bulging can be minimized utilizing annealed material and performing ISF with larger tool diameter and step size. The bending under tension analysis reveals that the formation of bulge is an outgrowth of bending moment that the forming tool applies on the sheet during ISF. Furthermore, the magnitude of bending moment depending upon the forming conditions varies from 0.046 to 10.24 N·m/m and causes a corresponding change in the mean bulge height from 0.07 to 0.91 mm. The bending moment governs bulging in layered sheet through a linear law. These findings lead to a conclusion that the bulge defect can be overcome by controlling the bending moment and the formula proposed can be helpful in this regards.     

Stress-strain relations in elastoplastic solids with Dugdale-type cracks

Mechanical behavior of a two-dimensional elastoplastic solid with rectilinear cracks is investigated. Plastic strip model is used to reduce plasticity problem to the equivalent linear elasticity formulation. Two realizations of the mixed mode plastic strip model are considered: in-line plastic strips as proposed by Becker and Gross [Int. J. Fract. 37 (1988) 163], and inclined plastic strips of Panasyuk and Savruk [Appl. Mech. Rev. 47 (1994) 151]. The effective mechanical response predictions are based on the procedure presented in Kachanov et al., [Appl. Mech. Rev. 47 (1994) 151]. Stress-strain relations are obtained for parallel and randomly oriented non-interacting cracks. Results are compared with known elastic solutions.     

东营凹陷王庄-宁海地区流体包裹体分析与流体充注研究

利用流体包裹体分析技术，系统地分析了东营凹陷王庄-宁海地区覆盖所有含油层位的流体包裹体样品。包裹体荧光观察和均一温度特征分析揭示了包裹体发育期次为5期，说明该区油藏存在5次流体充注过程；据此确定了备期烃类的成藏期次。东营组沉积时期和明化镇组沉积末期的油气运聚均在成藏后遭受大气淡水淋滤和降解作用。沙三段原油可能经历至少2期稠油化作用。荧光观察进一步证实该区主要发生2期充注、2期成藏。     

The influence of plastic properties on chip formation

A two-dimensional finite-element model of the chip formation process is used to study the influence of the material law determining plastic flow on chip formation of titanium alloys at high cutting speeds. For simplicity, friction and thermo-mechanical properties of the tool are neglected in the simulations. Titanium chips are strongly segmented and therefore especially suitable to study the role of segmentation for the cutting force and other cutting parameters. Of special interest is the influence of the thermal softening parameter in the material law. Increasing thermal softening leads to a drastic decrease in the cutting force and a corresponding increase in chip segmentation. A variation of the hardening exponent is also performed. It is shown that the simulation results can be understood by using adiabatic flow stress curves. The variation of the hardening exponent leads to strongly differing chip shapes, although the cutting force stays nearly constant. This shows that mean cutting forces should not be used as simulation verification parameters.