Assessment of spray quality from an external mix nozzle and its impact on SQL grinding performance

Spray quality is the critical factor which decides the efficacy of Small Quantity Lubrication (SQL) technology in a high specific energy involved machining process like grinding. Yet, the understanding about spray quality, the actual process mechanics and its effect on machining performance is inadequate. The present work is an attempt to establish a correlation between the spray input variables, quality of the spray and machining performance of SQL grinding through modelling and experiments. Using computational fluid dynamic techniques, the variation of droplet size, droplet velocity, number of droplets and heat transfer coefficient have been analysed at different input parameters and the computed trends have been verified and validated. CFD modelling of spray indicates that it is possible to produce aerosol medium with high heat dissipation ability at moderately high air pressure and low flow rate. It also shows that any increase in atomising air pressure favourably leads to notable increase in wetting area and also results in substantial enhancement in heat dissipation ability. Reduction of residual stress is thus remarkably good. On the other hand, grinding fluid flow rate, if increased, offers significantly better lubricity and reduces the grinding force which also reduces tensile residual stress. Short spell grinding test results are found to be in good agreement with CFD results.     

Compiler compatible 5.66 Mb/mm2 8T 1R1W register file in 14 nm FinFET technology

1-read/1-write (1R1W) register file (RF) is a popular memory configuration in modern feature rich SoCs requiring significant amount of embedded memory. A memory compiler is constructed using the 8T RF bitcell spanning a range of instances from 32 b to 72 Kb. An 8T low-leakage bitcell of 0.106 μm² is used in a 14 nm FinFET technology with a 70 nm contacted gate pitch for high-density (HD) two-port (TP) RF memory compiler which achieves 5.66 Mb/mm² array density for a 72 Kb array which is the highest reported density in 14 nm FinFET technology. The density improvement is achieved by using techniques such as leaf-cell optimization (eliminating transistors), better architectural planning, top level connectivity through leaf-cell abutment and minimizing the number of unique leaf-cells. These techniques are fully compatible with memory compiler usage over the required span. Leakage power is minimized by using power-switches without degrading the density mentioned above. Self-induced supply voltage collapse technique is applied for write and a four stack static keeper is used for read Vmin improvement. Fabricated test chips using 14 nm process have demonstrated 2.33 GHz performance at 1.1 V/25 °C operation. Overall V_min of 550 mV is achieved with this design at 25 °C. The inbuilt power-switch improves leakage power by 12x in simulation. Approximately 8% die area of a leading 14 nm SoC in commercialization is occupied by these compiled RF instances.     

嵌人式与独立存储器设计上的差异分析和研究

进入21世纪,随着集成电路的发展,SoC(System on Chip)片上系统应运而生。而作为SoC重要组成部分的嵌入式存储器,在SoC中所占的比重正逐步增加,并起着越来越重要的作用,那么嵌入式存储器与独立的存储器芯片在设计上存在着哪些差异?对此本文将以NOR型闪存为例在制造工艺的选取、衍生产品的设计、功耗与噪声、后端功能仿真、测试与修复等方面进行分析和研究。     

构建媒体网络信息安全体系

通过对广州市电视台综合信息平台网络系统的应用现状及安全风险进行分析,提出基于网络层、系统层、用户层和安全策略管理全方位的网络信息安全体系.     

提高托盘利用效率的重要手段——电子信息化管理

托盘能否有效运用对物流的畅通与否关系重大,这已经引起了国内外专家和学者们的重视,并就此制定了托盘电子信息化管理系统,旨在更合理地使用托盘,推进托盘一体化和共用系统的建立。而RFID技术在托盘的电子信息化管理的应用更将大大提高物流的效率与准确性,托盘电子信息化管理将成为今后托盘管理的趋势。     

Nonstationary Simulation Model of Absorber with Falling Film of Suspension

A nonstationary model of SO₂ absorption from a gas phase to a countercurrent falling film of absorbing slurry was developed. Laminar, wavy and turbulent film structures were considered based on published information. Resistances to the mass transfer on the gas and the liquid sides of the interphase were considered, together with chemical reactions in the liquid phase. Relevant chemical equilibria in the liquid phase were modeled. Original experimental data on the neutralization reagent dissolution rate presented as a polydispersed two‐phase system of solids and on the rate of dissolved sulfite oxidation were used. The model was verified with experimental data from a laboratory‐scale falling‐film absorber using a single vertical tube under various geometrical and operating conditions, and a very good agreement was found with the experiment. Parametric sensitivity analysis showed the critical parts of the model.     

从微电子到"活动的硅"--系统集成的未来潜力

本文主要介绍微电子发展趋势、微电子与微机械结合、系统集成的未来潜力。     

数字电视用户管理系统

课题实现了数字电视用户管理系统的设计与开发,以Oracle数据库作为后台数据库,以C Builder 6作为前台开发工具,包括表的设计与界面的设计.实现了数字电视用户管理系统基本功能,基本上满足了实际商业运营的需要.     

阴,阳离子聚合物地层内凝胶化改善水驱效果的研究

研究了一杆阴离子聚合物（Ａｃ５３０）和一种阳离子聚合物（Ｍｂ５８１）在水溶液中形成凝胶的条件和过程、凝胶化学结构、形态、稳定性和力学性能。在模拟地层的二维微观模型内观测了两种聚合物驱替渗流、相逼、形成凝胶、凝胶封堵大孔道的机理。在亲水填砂模型内测定了阴、阳离子聚合物凝胶体系降低渗透率的能力。     

Test Case Generation as an AI Planning Problem

While Artificial Intelligence techniques have been applied to a variety of software engineering applications, the area of automated software testing remains largely unexplored. Yet, test cases for certain types of systems (e.g., those with command language interfaces and transaction based systems) are similar to plans. We have exploited this similarity by constructing an automated test case generator with an AI planning system at its core. We compared the functionality and output of two systems, one based on Software Engineering techniques and the other on planning, for a real application: the StorageTek robot tape library command language. From this, we showed that AI planning is a viable technique for test case generation and that the two approaches are complementary in their capabilities.