Influence of iron oxide pigments on the properties of concrete interlocking blocks

Concrete interlocking blocks (CIBs) are utilized in a variety of commercial, municipal, and industrial applications. Superior engineering properties, low maintenance, ease of placement and removal, reuse of original blocks, aesthetic appeal, and immediate availability are the primary reasons for choosing concrete block pavement over other paving surfaces. It is a common practice to pigment building materials, such as mortar, concrete pavers, concrete roof tiles, and prefabricated concrete products; CIBs are colored using iron oxide pigments. This article presents experimental results detailing the properties of CIBs dyed with pigments. The results of these experiments are as follows: Because the particles of iron oxide pigments are finer than those of brown iron oxide, interlocking blocks mixed with the former acquired higher color strength than with the latter. Additional analysis determined a definite relationship between the flexural strength and the absorption ratio of pigment-dyed blocks; the correlation coefficient (R²) of interlocking blocks at 91 days was .90. It is suggested that if iron oxide pigments are to be used to color CIBs, the pigment-to-cement ratio should be below 4%.     

A portable cryo-storage system for low-temperature scanning electron microscopy,suitable for international transport of cryo-specimens

A cryo-specimen storage system for low-temperature scanning electron microscopy (LTSEM) specimens is described, which: liberates multi-specimen experiments from sampling restrictions imposed by the rate at which LTSEM specimens can be examined in the SEM; provides security against experiment loss resulting from breakdown of the SEM or cryo-system; enables collection of specimens in the field or in laboratories remote from the SEM laboratory; and facilitates international air transport of LTSEM specimens. The components of the system, which has a capacity of 98 stub-mounted specimens, are readily made in a laboratory workshop. The details of the design may be altered to suit particular specimen types or experimental approaches.     

What causes differences of C-S-H gel grey levels in backscattered electron images?

Backscattered electron (BSE) images of heat-cured concretes show alite grains surrounded by inner C-S-H gel of two distinct grey levels (referred to as two-tone inner C-S-H gel). The lighter rim forms at elevated temperature whereas the darker rim develops during subsequent exposure to moisture at 20 °C. This microstructural feature can potentially be used as an indicator to assess the curing history of a concrete. However, microstructural examinations of room-temperature concretes containing silica fume or which have been exposed to severe conditions (external sulfate, carbonation) also show distinct rims of two-tone inner C-S-H gel.The chemical compositions of the rims were determined by EDX microanalysis in the scanning electron microscope (SEM). Our results show that for heat-cured samples, the different grey levels of the two-tone inner C-S-H are caused by relative differences in microporosity and water content and not by ones in chemical composition. However, in silica-fume blended concrete, sulfate attacked or carbonated specimens the different grey levels of the two-tone inner C-S-H gel were associated with significant differences in chemical composition. This difference allows two-tone inner C-S-H gel arising from heat curing to be distinguished from that arising from these other causes.     

特征X射线能谱法测定Fe^＋注入小麦种子的深度

用１１０ｋｅＶ Ｆｅ＾＋离子束垂直注入小麦种胚后，在扫描电子显微镜上沿种子纵沟剖面，在不同深度上测量Ｆｅ元素被激发出的特征Ｘ射线强度分布，结果表明分布呈指数衰减，与晶体中的热扩散分布相类似，并对此进行了讨论。     

Dissolution of Ti wires in sulphuric acid and hydrochloric acid solutions

Ti wire electrodes were immersed in acidic solutions containing H₂SO₄ and HCl of various concentrations at 353 K to evaluate corrosion rate by measurement of electric resistance change (resistometry). Addition of hydrochloric acid to sulphuric acid solution promoted depassivation of Ti. After depassivation, the immersion potential dropped to the hydrogen evolution potential and a hydride layer was formed on the surface. The hydride layer dissolved continuously in the acidic solution. SEM observation showed that Ti wires dissolved almost uniformly in the early stage and that the dissolution then trace became irregular due to nonuniform growth of the hydride layer. Dissolution rate of a Ti wire was estimated almost accurately by resistometry.     

钙矾石膨胀机理的SEM研究

本文利用扫描电镜观察了在具有不同矿物组成的系统中生成的钙矾石的形成与膨胀机理。发现能够产生膨胀的钙矾石是由局部化学反应所生成；它们在未水化的铝酸盐矿物表面原地结晶，呈放射状生长。通过溶解，沉淀生成的钙矾石不能凝结，没有膨胀性。     

Antimicrobial finishing of regular and modified polyethylene terephthalate fabrics

An effective two-stage method has been developed for imparting antimicrobial properties to regular polyethylene terephthalate (R-PET), polyethylene glycol modified polyethylene terephthalate (PEG-M-PET), R-PET/Cotton blend (R-PET/C) and PEG-M-PET/Cotton blend (PEG-M-PET/C) fabrics. The method consists of partial hydrolysis of the fabrics to create carboxylic groups in PET macromolecules followed by subsequent reaction with dimethylalkylbenzyl ammonium chloride (DMABAC) under alkaline conditions. The reaction conditions such as pH, reaction temperature and time, carboxylic content, and DMABAC concentration were studied. Characterization of the finished fabrics was carried out through scanning electron microscopy (SEM) and Fourier transform infrared spectra (FTIR). All the modified PET fabrics showed excellent antibacterial activity towards Gram-positive (Bacillus mycoides), Gram-negative (Escherichia coli), and nonfilamentous fungus (Candida albicans). The achieved antimicrobial functions on the PET fabrics are durable in repeated laundering processes. Even after laundering 10 times the fabrics could still provide more than 85% of its antimicrobial activity against B. mycoides, E. coli, and C. albicans. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Morphological aspects of rubber fracture and wear

Morphology of carbon black (CB)‐filled rubber was studied with AFM and SEM and the classification of filler agglomerates, based on their internal structure and filler–matrix interactions, has been proposed. It varies according to the activity of CB and the kind of rubber. It has been shown that fracture of rubber starts either inside filler agglomerates (de‐cohesion) or in a filler–matrix interphase (de‐adhesion) initiating wear of the material. Microscopic observations correlate well with TGA and EPR data of wear debris collected during friction of rubber. The increase of thermal stability of CB and the appearance of additional spin signals, respectively, for elongated samples or debris, are proposed to be associated with de‐cohesion or de‐adhesion of the agglomerates. New approach to the fracture of rubber called “fatal agglomerate concept” is presented. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Compatibility between Polyamide 6 and Polycarbonate

Polyamide （PA6） and polycarbonate （PC） were prepared by a Brabender mixer （ PLV- 151） at 240℃ with 30 rpm for duration of 8 and 6 minutes respectively. The epoxy resin （E） addition can lead to substantial microstructural changes in the PA6/PC blends. Scanning electron microscope （SEM） was used to observe the mixtures characterized by the domains of clearly segregated homophases and voids between the two polymers. PA6/PC of polyamide 6 and polycarbonate with epoxy resin addition under the composition ratio of 20/80, 20/80/1, 40/60/1 and 40/60, were tested to verify the key role of epoxy in promoting the compatibility of PA6 with PC during blending.     

特种钢用结晶器铜管破裂原因分析

通过对某特钢厂破裂的结晶器铜管进行金相实验、扫描电镜和能谱分析,并结合结晶器的生产、使用及失效过程情况,综合受力分析,认为铜管破裂原因主要是环境介质硫渗入形成硫化物,在拉应力作用下,裂纹沿脆性质点扩展导致的破坏。