杭州湾南岸滩涂沉积物中HCHs与DDTs污染特征分析

摘 要：目的 了解六六六（hexachlorocyclohexanes,HCHs）与滴滴涕(dichloro diphenyl trichloroethanes,DDTs)在杭州湾南岸滩涂沉积物中的污染现状。方法 于2018年4月，采集杭州湾南岸地区4个采样点不同深度（0~80 cm）滩涂沉积物，利用气相色谱-串联质谱法（gas chromatography tandem mass spectrometry, GC-MS/MS）测定了该区域中HCHs与DDTs的含量，对其分布规律进行分析，使用共识沉积物质量基准法对其生态学风险进行了评估。结果 所有样品中均检出，HCHs与DDTs含量分别为4.20~6.24 μg/kg与3.37~4.73 μg/kg，主要以β-HCH、δ-HCH以及DDE为主，其污染主要来源于历史性工业品，整体污染处于较低水平；20.3%的沉积物样品中DDEs含量以及28.1%的样品DDTs总量介于阈值效应浓度(threshold concentration, TECs) 和可能效应浓度(probable effect concentration, PECs)之间。结论 杭州湾南岸沉积物中HCHs与DDTs的污染处于较低水平，具有较小的生态学风险。     

基于FPGA&ASIC的专用USB接口设计与实现

无驱型USB KEY专用接口的设计和实现是基于FPGA&ASIC的. 该设计主要使用Verilog语言在FPGA上实现USB协议,并提供针对USB收发器和微控制器的接口. 通过该接口USB KEY在接入系统后不需要驱动程序即可正常使用. 该设计通过了软件的仿真并在FPGA上进行了硬件验证.     

Vulnerability Analysis of the Grid Data Security Authentication System

ABSTRACT

A password-based authentication is still the most prevalent authentication method because of its convenience and easy implementations. Since a password is transmitted via network, it has an inherent vulnerability of password exposure to an attacker. A one-time password system reduces the risk of a security breach even when a password is exposed to an attacker, because the password is only meaningful at a given time. A grid data security system uses a technology, GridOne?, which allows the use of a one-time password without requiring preinstalled hardware or software infrastructures, and it provides strong security over conventional password-based authentication systems. We analyzed the weakness of the grid data security authentication system and provide a suggestion to compensate for its vulnerability.     

使用USB KEY控制Windows 2000/NT开机登录

分析了Windows 2000/NT系统中开机登录过程,提出了使用USB KEY控制Windows2000/NT开机登录的方法,从而克服了使用口令字控制开机登录所带来的安全性问题,文中提出的开机登录控制技术同样适用于指纹识别设备、视网膜扫描等其它硬件身份设别设备.     

建筑实践中的材料选择

文章的重点是讨论在具体的建筑实践中材料与建筑的本质性关联,亦即与设计的意图和特征、与建筑的发生密切相关的内容。在多数实践中,设计围绕核心意图展开,在意图的指引下选择对应的材料,形成特定的特征而达到预设的目标;而另外一些实践,则是因既定材料而引发设计,甚至发展出具有持续性的工作和研究方向,如"砌筑"和"组配";材料与空间、结构、形式的同一性也成为近年来特定类型建筑实践中的某种既定追求。     

基于建筑视觉场的广场标志物高度控制域研究

摘要　建筑视觉场是用来描述建筑体量与空间尺度对人的视觉心理感知影响程度的重要方法。通过建筑视觉场,结合 相关视觉机制与心理物理学,定量解析意大利经典支配型广场空间实例中标志物高度对人的视觉心理的影响程度,并 归纳出普遍性的视觉规律,揭示空间图景视觉平衡状态下标志物高度与广场尺度间内在的耦合关系,希望能够对当前 广场标志物的设计有所助益。     

基于防范疫情的健康住区风环境设计研究 ——以岭南月岛住区为例

摘要　随着新冠疫情的发展,住区的健康问题成为人们关注的焦点。旨在防范疫情的视角上,系统的对健康住区风环 境的设计进行研究。采用文献阅读、实地调研、现场实测、数值模拟等方法,在新冠疫情防范及健康住区文献综述的 基础上,梳理出健康住区风环境设计的必要性。以岭南月岛住区为例,通过实地调研、现场实测对月岛住区进行深入 了解,结合健康住区风环境的相关规范导则,总结出健康住区风环境设计的具体要求。从而使用Phoenics 软件对月 岛住区从群落、组团、单体三个层面进行数值模拟、对标评判、系统分析,进而发现三个层面存在通风不佳,空气污 染等问题。然后对这些问题进行重点优化、模拟验证、再次评判。最终,提炼总结出在防范疫情的同时,对于健康住 区风环境的设计,应以绿色、智慧、健康为导向,因地制宜,健康发展。     

Development of process for thermomechanical treatment of ultrahigh strength steel prepared by electroslag refining

Abstract

Thermomechanical treatment (TMT) is the simultaneous use of work hardening, and grain refinement along with solid solution and precipitation strengthening. In this investigation, four alloys, with a base composition of 0·28%C, 1·0%Mn, 4·2%Cr, 1·0%Mo, 0·34%V, were prepared by electroslag refining (ESR) and by addition of small amounts of Ti and Nb and by increasing Cr and V to 4·8 and 0·48% respectively. In two of the alloys a yield strength in excess of 1550 MPa was obtained in the as cast quenched and tempered condition. Attempts were made to further increase the yield strength by thermomechanical treatment. The process parameters for thermomechanical treatment were optimised by adopting procedures such as calculation of stability of precipitates, hot compression test, determination of cooling rates in different coolants, and modelling of TTT and CCT diagrams. The process involved prerolling of the ESR ingot to a bar at 1200°C, followed by hot rolling in two passes starting from 950°C and finishing at 850°C with equal deformation of 25% in each pass to convert the bar into plates. These were immediately cooled in one of the cooling media: air, polymer–water solution (1 : 1·5) and oil. Yield strength in excess of 1750 MPa was obtained in oil cooled specimens of the alloy with titanium addition and that where Cr and V were increased. The niobium added specimen gave strengths, similar to that obtained for the base alloy, in spite of the fact that the as cast alloy had shown very high strengths, presumably because of the high soaking temperatures and grain growth. Air cooling gave the lowest strengths and oil cooling the highest.     

Steady Crawl Gait Generation Algorithm for Quadruped Robots

The capability of stable walking on irregular terrain is the primary advantage of legged robots over wheeled mobile robots. However, the traditional foothold selection-based gait generation algorithms are not suitable at some points for blind robots which cannot obtain the exact terrain information. A velocity-based gait generation algorithm with real-time adaptation rules which are necessary for steady walking is suggested. Particularly, we have developed a steady crawl gait with duty factor β = 0.75. The main feature of the suggested algorithm is that it is not based on foothold selection and it can be used for the walking of blind robots on more realistic irregular terrain. The adaptation rules are the translational velocity modification to satisfy the steady gait requirement and the swing period modification to avoid the kinematic limitation. The suggested gait generation algorithm has been implemented in a simple quadruped robot that has a total of eight actuated joints on the legs. Using PD controllers for each actuated joint for the trajectory following and the adaptation algorithm of gait parameters, the steady periodic crawl gait on irregular terrain has been demonstrated.     

Influence of clamping support distance on distortion of welded T joints

Abstract

A study is presented on the influence of the clamping support distance on welding distortion of 6 mm thick gas metal arc welded structural steel T joints. Experiments were performed for two clamping conditions and are compared to simulations based on a previously presented model. It was found that clamping closer to the weld seam reduces angular as well as bending distortion. In order to assess the accuracy of the results, sensitivity analyses were performed on the influence of predeformation and material parameters. It is shown that an initial predeformation has an influence on the final welding distortion. Additionally, it has been found that selection of material properties within the range of variations permitted by the material norms has a strong influence on the predicted distortion. Results were improved using material specific data rather than generic data for the relevant material class. Also the assumed phase volume change plays an important role.