排气系统在注射模中的应用

介绍了排气系统在注射模中的重要性,排气系统位置的选择,排气系统的种类以及应用等     

橡胶Mooney—Rivlin模型材料系数对轴向刚度影响分析

在橡胶小变形范围内，采用理论推断的方法，得到在相同硬度下橡胶Mooney—Rivlin模型材料系数由C2／C1决定的关系式。并采用ABAQUS有限元软件分析的方法，结合橡胶轴向刚度常规解，分析了C2／C1不同值对橡胶轴向刚度的影响进行，结果显示其影响呈现一定规律性。     

AXIAL PHASES DISTRIBUTION AND HOMOGENIZATION IN THREE-PHASE FLUIDIZED BEDS

We have investigated the axial distribution of the liquid phase in a three-phase fluidized bed in which the particles were glass beads of two different diameters, 710-850 μm and 2 mm. Two methods were used to reduce the axial heterogeneity and homogenize the bed: the use of packing elements and the addition of a small quantity of a high molecular weight polymer. The use of packing elements was shown to be very efficient in controlling phases distribution in the bed. The packing consisted of 1 mm thick steel horizontal plates punched and stretched to obtain parallelogram-shaped openings. The addition of a high molecular weight polyisobutylene (BASF Oppanol B246, M_u, =6.15 Lo⁶) on the phase distribution was also studied. Low polymer concentrations up to 397 ppm (based on the liquid phase) were investigated. The addition of the polymer reduced bubble coalescence and allowed for a better distribution of the phases.     

POWER CONSUMPTION WITH ANCHOR MIXERS EFFECT OF BOTTOM CLEARANCE

The effect of bottom clearance on power draw for anchors is investigated. The results suggest that power input decreases as the bottom clearance ratio b/D increases. A new correlation is proposed in which both bottom and wall clearance effects on power input are considered. The dependence of power input on these effects is additive rather than multiplicative. Thus, the total power consumption is the sum of the power inputs generated by the wall and bottom clearance. Power results from 3D-CFD numerical simulations are also presented. These results confirm fairly well the experimental points.     

容器设计中搅拌装置的轴向力分析

搅拌装置在化工厂中应用很广，在磷肥、钛白粉装置中（15kt/a)使用较多，仅钛白粉装置中就大约有40－50台，如增稠结晶器，中和槽等，搅拌操作所涉及的因素极为复杂，浆叶形式的选择，从力学的观点来说，迄今研究不够，本文就搅拌装置产生的轴向力问题进行了初步研究。     

Set methods of left-turn waiting zone at signalized intersection

To maximize the number of vehicles passing by the stop-line in a cycle and improve the operation efficiency of intersection in China,the settlement of left-turn lane waiting-zone is becoming prevailing. Based on conflicting-point method,the internal mechanism of left-turn flow after stopping line was analyzed through taking postposition left-turn lane waiting-zone intersection for instance. The relationship between the first left-turn vehicle and the last vehicle of previous phase passing the conflicting point was expounded. According to the time of successive arriving of two vehicle flows at conflicting-point,the reasonable layout for waiting area of left-turn vehicles was researched when the clearance index was less than 0. The results suggest that the appropriate layout for waiting area of left-turning vehicles can improve the operation efficiency of intersections.     

橡胶冲裁模具刃口间隙的探讨与研究

阐述了合理选择丁基橡胶瓶塞冲裁模具的刃口间隙是提高模具使用寿命的关键，介绍了模具刃口间隙的确定方法。     

同轴型热虹吸系统轴向传热特性实验研究

对一种用于冷中子源系统的自然循环进行了轴向传热特性研究,建立了以氟里昂为工质的同轴型热虹吸管传热实验系统。研究表明:同轴型热虹吸系统可强化轴向热传输能力,其传热工况有过冷沸腾流动振荡工况、稳定工况和烧干工况3类。在低功率区,过冷沸腾和携带机制造成启动过程的两相流振荡;进入稳定工况区后,系统具有自调适能力,能够维持恒定的循环质量流率;在高功率区,蒸发器烧干产生传热极限。本研究显示出同轴型热虹吸系统的动力特性与普通自然循环系统有明显区别,其循环机制与普通热虹吸系统有本质区别。     

蒸发时间对两级凝胶法制备的聚醚砜膜结构和性能的影响

主要探讨了蒸发时间对用两级凝胶法(dual—bath coagulation method)所制得的聚醚砜(PES)超滤膜的性能和结构的影响．结果表明，随着蒸发时间的延长，水通量先减小后增大；肌肝和尿素去除率均是先升高而后降低，然后再升高的趋势；膜的孔隙率上升，平均孔径下降．在蒸发时间为10s时，肌肝和尿素去除率最高，且水通量适中，是血液净化用聚醚砜膜的最佳成形条件．     

Axial offset control of PWR nuclear reactor core using intelligent techniques

Improved load following capability is one of the main technical performances of advanced PWR (APWR). Controlling the nuclear reactor core during load following operation encounters some difficulties. These difficulties mainly arise from nuclear reactor core limitations in local power peaking, while the core is subject to large and sharp variation of local power density during transients. Axial offset (AO) is the parameter usually used to represent of core power peaking, in form of a practical parameter. This paper, proposes a new intelligent approach to AO control of PWR nuclear reactors core during load following operation. This method uses a neural network model of the core to predict the dynamic behavior of the core and a fuzzy critic based on the operator knowledge and experience for the purpose of decision-making during load following operations. Simulation results show that this method can use optimum control rod groups maneuver with variable overlapping and may improve the reactor load following capability.