Study on the non-uniform contact during ELID groove grinding

This paper introduces the potential feasibility that ELID (electrolytic in-process dressing) grinding replaces superfinishing in bearing manufacturing, but ELID grinding will bring new challenges. Different regions present distinguish surface profile due to the non-uniform contact in ELID groove grinding. However, few reports explaining the non-uniform contact are available. This article explores the mechanisms of the non-uniform contact during ELID groove grinding. Experiments on the non-uniform contact between bearing raceway and grinding wheel have been carried out under different conditions. The results show that non-uniform contact exists in ELID groove grinding process and it exerts influence on the profile of the raceway surface. Non-uniform contact influences the Rsk and Rku value all the time, but it influences the Ra value occasionally. Improvement strategies of eliminating the non-uniform contact are also discussed based on the experimental study.     

可调偏迈步式胶带自移机尾的研究

随着掘进工作面自动化程度的提高,掘进巷道速度也在日益加快,而现有的顺槽皮带机机尾移动缓慢且移动时工作量大,需要两三人配合操作,存在一定的安全隐患。针对以上问题,研发可调偏迈步式胶带自移机尾,具有与悬挂二运皮带转载机搭接行程长,可以迈步式前进,自动调偏等功能,同时,可以降低工人的劳动强度,加快巷道掘进速度。     

皮带秤秤架的响应特性曲线分析

介绍了皮带秤秤架响应特性曲线分析方法，对四种结构形式的秤架进行了响应特性曲线分析和比较，得出的结论是：悬浮式秤架的计量特性最好。     

Methods of Verifying Continuous Automatic Belt Weighers: State and Prospects

The basic methods of verifying continuous automatic belt weighers are described. A comparative analysis of these methods on the basis of experimental studies is made and ways of implementing the results in industry are recommended.     

浅谈延迟焦化装置露天栈桥的设计

根据延迟焦化装置露天栈桥的工程设计实践,围绕一炉两塔(一个加热炉两个焦炭塔)的焦化装置,分析了露天栈桥设计中的要点及难点,对其在平面布置、基础安排和吊车梁选型等设计方面做一些介绍和论述。     

长距离钢带传动的张紧机构设计与应用

比较了几种长距离传动方式的特点与适用场合，重点探讨了实现长距离精密传动的技术要点。结合实际工程，完成了长距离钢带精密传动的应用，并指出张紧机构的设计与应用是钢带实现长距离精密传动的关键。为此文中对钢带传动的典型张紧机构进行了比较，并分析了这几类张紧机构的应用情况，有参考和应用价值。     

Simulation of Strength Distribution in Ground Ceramics by Incorporating Residual Stress Effect

Strength of ground ceramics may be affected by residual stress as well as surface flaws induced by grinding. Strength prediction for ground ceramics is convenient for mechanical design of ceramic components. In this article, a numerical procedure based on fracture mechanics was proposed to estimate strength distribution of ground ceramics by considering grinding-induced residual stress. Bending strength and residual stress of ground ceramics were measured for three grinding-conditions. By comparison of simulated results with experimental ones, it was revealed that strength characteristics in experiments were well simulated by using the proposed procedure.     

煤炭码头带式输送机控制系统

介绍煤炭码头带式输送机联锁控制系统设计的一种方法，详细阐述了整个系统的工艺流程、启动方式以及控制原理等。这种方法可以实现带式输送机远程中控室控制，也可进行就地带式输送机机侧控制。     

成形磨削中砂轮修整精度的研究

成形磨削一般采用金刚石笔来修整所需要的砂轮形状，金刚石笔在安装中的位置误差将影响被加工工件的精度，本文对此误差的大小进行了分析。     

非织造产业中塑胶网带的用途

介绍了塑胶网带的用途和网带的种类 (玻璃纤维网带、金属网带和塑胶网带 )及其优缺点 ,并对网带的透风率、网带清理及网带收缩等问题进行了讨论