基于FLAC3D的破碎围岩巷道支护效果分析

为了解破碎围岩分别采用锚杆支护、锚喷支护以及锚喷+锚索耦合三种支护方式下的支护效果,进而为破碎围岩巷道选择合理的支护方式提供参考。通过借助FLAC^3D软件建立数值模型,分析不同支护条件下的破碎围岩巷道位移量、应力分布以及塑性区的时空演化特征。结果表明,采用锚喷+锚索耦合支护时,可以较好的控制巷道围岩的位移量、减小应力集中效应、缩小塑性区的影响范围。     

面向工程应用的单片机课程教学改革与实践

在分析传统单片机教学存在问题的基础上,提出面向工程应用,聚焦企业需要,构建能力递进、面向应用的内容体系,搭建资源共享、实践创新、师生互动的自主学习平台,组建培养兴趣,突出技能的“双师型”教学团队,实践表明,在传授知识的同时,能有效提升学习兴趣,优化人才素质结构。     

Influences of chip serration on micro-topography of machined surface in high-speed cutting

Saw-tooth chip changes from macroscopically continuous ribbon to separated segments with the increase of cutting speed. The aim of this study is to find the correlations between chip morphology and machined surface micro-topography at different chip serration stages encountered in high speed cutting. High strength alloy steel AerMet100 was employed in orthogonal cutting experiments to obtain chips at different serration stages and corresponding machined surfaces. The chips and machined surfaces obtained were then examined with optical microscope (OM), scanning electron microscope (SEM), and white light interferometer (WLI). The result shows that chip serration causes micro-waves on machined surface, which increases machined surface roughness. However, wave amplitudes (surface roughness) at different serration stages are different. The principal factor influencing wave amplitude is the thickness of the sawed segment (tooth) of saw-tooth chip. With cutting parameters in this study, surface roughness contributed by chip serration ranges from 0.39 μm to 1.85 μm. This may bring on serious problems in the case of trying to replace grinding with high-speed cutting in rough machining. Some suggestions have been proposed to control the chip serration-caused surface roughness in high-speed cutting based on the results of the current study.     

新型的芯片间互连用CMOS/BiCMOS驱动器

从改善不同类型 IC芯片之间的电平匹配和驱动能力出发 ,设计了几例芯片间接口 (互连 )用 CMOS/Bi CMOS驱动电路 ,并提出了采用 0 .5 μm Bi CMOS工艺 ,制备所设计驱动器的技术要点和元器件参数。实验结果表明所设计驱动器既具有双极型电路快速、大电流驱动能力的特点 ,又具备 CMOS电路低压、低功耗的长处 ,因而它们特别适用于低电源电压、低功耗高速数字通信电路和信息处理系统。     

单片机控制下液晶显示器的使用

介绍液晶显示器EDM12864B的原理及其在单片机控制下的简单应用。     

基于EPF10K30的ISA接口设计

随着计算机技术日新月异的发展。计算机控制已经深入到了各个领域，特别是在工业控制领域，计算机通过ISA总线与接口电路进行通信，然后由接口电路去控制被控设备，从而完成预期的控制工作．     

AT89C51单片机在电话远程控制器中的应用

设计以AT89C51单片机作为控制核心的电话远程控制器,重点介绍该控制器的各模块组成、原理及具体实现的电路,该控制器采用现有的电话线路进行通信,无需重新布线且通信距离不受限制,经实际运行表明,该控制器具有运行可靠、成本低、操作方便,适用性强的特点、可以广泛应用于城市社区,具有较大的推广价值。     

Failure analysis of a broken tooth

Several days after heart surgery, a patient discovered his upper right canine tooth had broken at the root. Such tooth damage, recognized post-operatively, is usually assumed to be caused by blunt mechanical force from an instrument used by the anesthesiologist during placement of a breathing tube at the start of surgery. In this case, the patient had saved the crown portion of the broken tooth, and it was possible to examine the root fracture characteristics. The curvature and direction of the crack path and natural tooth situation suggested that failure could be described through a cantilever beam model. This was confirmed when a whole extracted sample tooth was embedded and broken by a measured force in a manner consistent with the model. The resulting fracture surface matched that of the patient’s broken canine tooth. However, the high load and force direction necessary to fracture the root was inconsistent with forces applied during the anesthesia procedure. The failure analysis and further investigation indicated tooth clenching on the breathing tube during recovery was the likely cause of fracture. This paper presents an alternate explanation for intubation-related dental injury, demonstrates the practicality of fractographic analysis of biological materials, and introduces a methodology for simulating in vitro tooth settings for mechanical testing.     

一种单片机控制的指令转换器的设计

采用89C51单片机，串口扩展芯片8251、中断扩展芯片8259等器件设计了一种指令格式转换器。     

用6805实现宽范围高精度频率测量

采用ＭＣ６８０５系列单片机并充分利用其定时器，选择测频法或测周法，可以实现定范围、高精度频率测量。此种方法只占用１个内部定时器，节省了硬件开销。