Strain‐rate‐dependent mechanical properties of polypropylene separator for lithium‐ion batteries

The mechanical integrity of battery separators is critical for battery safety and durability. A comprehensive study of strain‐rate‐dependent tensile and puncture properties of a polypropylene lithium‐ion battery separator is presented here with a new model. Due to anisotropy of the polymeric membrane, tensile testing was conducted for different directions. Results showed that tensile strength and elastic modulus were increased 1000% and 500%, respectively, for different directions. It was also demonstrated that tensile strength changed 10 to 25% with strain rate (1.67 × 10^?4 to 1.67 × 10^?1 s^?1) for different directions. An equation was obtained for the first time for flow stress versus strain rate at varied tensile directions with respect to machine direction. Moreover, puncture testing was performed and it was shown that puncture strength was increased 140% with increasing strain rate from 0.25 to 250 mm min^?1. Two failure modes were also observed in puncture samples. Finally, Eyring's model was used to calculate activation enthalpy of the porous polypropylene separator. © 2020 Society of Chemical Industry     

葛洲坝水利枢纽泄水建筑物进水口冲磨与修复

葛洲坝水利枢纽工程已运行20余年，近年水下检查中发现泄水建筑物进水口存在不同程度的冲磨，有些已威胁到建筑物安全运行，分析冲磨原因和探讨修复材料和手段是非常重要的，本文就此问题提出一些看法和建议供参考。     

高温旋风除尘器的设计

在PTA(精对苯二甲酸)的生产过程中,工艺废气经尾气膨胀透平机降压后进入RTO蓄热式焚烧炉将有毒有害的有机物焚烧分解后排入大气,为了达到粉尘的排放标准(小于120mg/m~3),在焚烧炉之后加上这台高温烟气除尘器,废气经除尘后达到了排放标准,而且最大程度地减少了热量损失,实践证明此项改造是成功的。文章探讨如何进行高温烟气除尘器的设计,并介绍了高温多管陶瓷旋风烟气除尘器的结构。     

丝网气液分离器分离性能和压力损失分析

对丝网气液分离器的分离机理进行了详细分析,在此基础上给出了丝网气液分离器的分离效率和压降计算公式。与HG/T 21618-1998《丝网除沫器》中的公式相比,此公式可以用于任意组合的丝网结构,更具普适性,并且能定量分析各种分离机理对分离的贡献。对丝网式空气过滤器计算的结果表明,此公式具有很好的精度,可以用于工程设计。     

井下液气分离器分离原理及结构改进

液气分离器就是充分利用电泵机组的高转速、气体和液体之间悬殊的密度差异进行液气离心分离。经过多年的发展,在传统的液气分离器结构基础上又出现了许多新的设计和改进,大大提高了液气分离器的分离效果。文章重点论述了液气分离器的分离原理和结构上的改进之处。     

水力旋流器用于酸性油分离的研究

采用自行研制的水力旋流器进行了降低酸性油酸值的工业实验。实验表明,水力旋流器可将酸值为13．3 mgKOH/g的酸性油酸值降至12 mgKOH/g左右,从而能满足工业生产要求,沉降时间大为缩短。     

重介选煤厂自动化控制系统

介绍了重介选煤厂实现全自动控制的系统原理及所能实现的各项功能。     

旋风分离器结构改进的研究

根据旋风分离器的工作原理及应用特点 ,分析了影响旋风分离器分离效率的因素及结构存在的问题 ,并提出了改进措施 ,即内管外壁增设螺旋翼片 ,扩散形锥体改为悬挂挡板。通过实验观察 ,改进结构的旋风分离器分离效率比常规旋风分离器高。实践证明 ,对于密度差异较小的非均相物系的分离 ,只要对旋风分离器作适当改进 ,仍能取得令人满意的效果 ,这大大拓宽了旋风分离器的应用领域     

PIM卧管式三旋在催化裂化装置上的应用

分析了PIM卧管式三旋在催化装置应用过程中所出现的问题 ,并且有针对性地进行了改造 ,取得了良好的效果     

Modeling and simulation of a fully air swept ball mill in a raw material grinding circuit

A raw material grinding circuit was modeled using plant data. Samples were collected from around the circuit and, following a crash stop, from inside the mill. The size distributions of the samples were determined down to a few microns. Using the data from inside the mill a modeling approach, based on perfect mixing, was developed. The modelling approach implicitly assumes that the mixture of feed materials broken is homogenous from the breakage point of view. The air classification around the circuit was modeled using the efficiency curve approach. In order to measure the success of the method the circuit performance was predicted by simulation studies while it was operating at different conditions. The results were then compared with the measured data. It is concluded that modeling gives a useful quantitative indication of what may occur in fully air swept mills.