磨料有序排布电镀砂轮的制备及其把持力研究

为解决电镀砂轮磨削加工中容屑空间不足的问题，采用点胶微粘接的方法制备了磨料有序排布的电镀砂轮，分析了磨料粘接效果和镀层力学性能。通过SEM分析了磨料/镀层/导电胶的结合界面，并进行了干磨削试验。研究结果表明，直径约为磨料粒径40%的胶点可粘接住磨料，单个胶点上粘接多颗磨料的占比小于6%；双脉冲电镀工艺制备的镀层显微硬度大于500HV，表层残余应力小于100MPa，磨料/镀层/导电胶之间的界面贴合紧密，无明显缺陷；砂轮在磨削时没有出现磨料脱落现象。     

一种新型地雷战斗部的数值模拟研究

针对地雷的毁伤目标和特性,提出一种新颖的多棱柱状药型罩结构,其可看作由八个楔形罩对称排列相邻连接而成。应用非线性有限元软件完成了爆炸载荷下多棱柱状药型罩形成射流过程的数值模拟,结果表明新型药型罩结构能够实现预期设想,形成一股汇聚射流。研究结果为地雷战斗部研究提供了一种新的选择。     

Experimental study of crystal anisotropy based on ultra-precision cylindrical turning of single-crystal calcium fluoride

To realize ultimately efficient signal processing, it is necessary to replace electrical signal processing circuits with optical ones. The optical micro-resonator, which localizes light at a certain spot, is an essential component in optical signal processing. Single-crystal calcium fluoride (CaF₂) is the most suitable material for a highly efficient optical micro-resonator. The CaF₂ resonator can only be manufactured by ultra-precision machining processes, because its crystal anisotropy does not allow the application of chemical etching. However, the optical micro-resonator's performance depends definitely on the surface integrity.This study investigated the relationship between surface quality after ultra-precision machining and crystal anisotropy. Firstly, crack initiation was investigated on the (1 0 0), (1 1 0), and (1 1 1) planes using the micro-Vickers hardness test. Secondly, brittle-ductile transition was investigated by orthogonal cutting tests. Finally, cutting performance of cylindrical turning was evaluated, which could be a suitable method for manufacturing the CaF₂ resonator. The most difficult point in cylindrical turning of CaF₂ is that the crystalline plane and cutting direction vary continuously. In order to manufacture the CaF₂ optical micro-resonator more efficiently, analysis was conducted on crack initiation and surface quality of all crystallographic orientations from the perspective of slip system and cleavage.     

Study on the non-uniform contact during ELID groove grinding

This paper introduces the potential feasibility that ELID (electrolytic in-process dressing) grinding replaces superfinishing in bearing manufacturing, but ELID grinding will bring new challenges. Different regions present distinguish surface profile due to the non-uniform contact in ELID groove grinding. However, few reports explaining the non-uniform contact are available. This article explores the mechanisms of the non-uniform contact during ELID groove grinding. Experiments on the non-uniform contact between bearing raceway and grinding wheel have been carried out under different conditions. The results show that non-uniform contact exists in ELID groove grinding process and it exerts influence on the profile of the raceway surface. Non-uniform contact influences the Rsk and Rku value all the time, but it influences the Ra value occasionally. Improvement strategies of eliminating the non-uniform contact are also discussed based on the experimental study.     

M1080B无心外圆磨床改进

M1080B无心外圆磨床砂轮及导轮宽度较窄,磨削轴承套圈外圆时,磨削效率低,托板架调整较为繁琐、皮带打滑、磨损较为严重。针对上述问题,提出了相应的解决办法,提高了磨削效率。     

Waves in generalized thermo-viscoelastic infinite continuum with cylindrical cavity due to three-phase-lag time-nonlocal heat transfer

Abstract

Generalized thermoelastic interactions due to three-phase-lag time-nonlocal heat transfer in a Kelvin-Voigt type infinitely extended visco-thermoelastic continuum with cylindrical cavity has been investigated. The two-temperature generalized thermoelasticity theory has also been taken into account. The problem has been solved in the domain of Laplace on the assumption that the surface of the cavity is free from traction and is subjected to a smooth and time-dependent-heating effect. Laplace inversion of the transformed solutions has been carried out numerically. The obtained numerical data for different considerations are plotted in graphs to study the effects of time-nonlocal parameter, two-temperature parameter and visco-thermoelastic relaxation parameter on different thermoelastic quantities of physical interest.     

Range of the Applicability of the Wilkins Method to the Investigation of the Dynamic Stress-Strain State of Anisotropic Elastic Axisymmetric Shells

The exactness and stability of the Wilkins method in the investigation of the stress-strain state of axisymmetric anisotropic elastic shells, including thick-walled ones, have been studied for different values of artificial viscosity, pulse load rise and fall time, and different deformation process durations. A comparison of numerical calculations, performed by means of an application software package developed by V. A. Romashchenko on the basis of the Wilkins method, with experimental results, known numerical data, and with calculations using the computation kernel LS-DYNA 3D has been carried out.     

Simulation of Strength Distribution in Ground Ceramics by Incorporating Residual Stress Effect

Strength of ground ceramics may be affected by residual stress as well as surface flaws induced by grinding. Strength prediction for ground ceramics is convenient for mechanical design of ceramic components. In this article, a numerical procedure based on fracture mechanics was proposed to estimate strength distribution of ground ceramics by considering grinding-induced residual stress. Bending strength and residual stress of ground ceramics were measured for three grinding-conditions. By comparison of simulated results with experimental ones, it was revealed that strength characteristics in experiments were well simulated by using the proposed procedure.     

成形磨削中砂轮修整精度的研究

成形磨削一般采用金刚石笔来修整所需要的砂轮形状，金刚石笔在安装中的位置误差将影响被加工工件的精度，本文对此误差的大小进行了分析。     

在线磨辊辊面粗糙度的实验研究

影响轧辊表面粗糙度的因素很多，为此对影响辊面粗糙度的因素进行了系统分析和实验研究，得出了轧辊和砂轮的速度、砂轮粒度、砂轮直径及磨削液等主要因素对轧辊表面粗糙度影响的一般规律。利用回归分析的方法建立了轧辊表面粗糙度的数学模型，并将计算值与实测值进行了比较，发现两者基本一致。此项研究为适时控制冷轧带钢在线磨辊辊面粗糙度提供了计算模型。