磨料有序排布电镀砂轮的制备及其把持力研究

为解决电镀砂轮磨削加工中容屑空间不足的问题，采用点胶微粘接的方法制备了磨料有序排布的电镀砂轮，分析了磨料粘接效果和镀层力学性能。通过SEM分析了磨料/镀层/导电胶的结合界面，并进行了干磨削试验。研究结果表明，直径约为磨料粒径40%的胶点可粘接住磨料，单个胶点上粘接多颗磨料的占比小于6%；双脉冲电镀工艺制备的镀层显微硬度大于500HV，表层残余应力小于100MPa，磨料/镀层/导电胶之间的界面贴合紧密，无明显缺陷；砂轮在磨削时没有出现磨料脱落现象。     

Mechanical Properties of Single-Layer Diamond Reinforced Poly(vinyl alcohol) Nanocomposites through Atomistic Simulation

Low-dimensional carbon nanostructures are ideal nanofillers to reinforce the mechanical performance of polymer nanocomposites due to their excellent mechanical properties. Through molecular dynamics simulations, the mechanical performance of poly(vinyl alchohol) (PVA) nanocomposites reinforced with a single-layer diamond – diamane is investigated. It is found the PVA/diamane exhibits similar interfacial strengths and pull-out characteristics with the PVA/bilayer-graphene counterpart. Specifically, when the nanofiller is fully embedded in the nanocomposite, it is unable to deform simultaneously with the PVA matrix due to the weak interfacial load transfer efficiency, thus the enhancement effect is not significant. In comparison, diamane can effectively promote the tensile properties of the nanocomposite when it has a laminated structure as it deforms simultaneously with the matrix. With this configuration, the interlayer sp³ bonds endows diamane with a much higher resistance under compression and shear tests, thus the nanocomposite can reach very high compressive and shear stress. Overall, enhancement on the mechanical interlocking at the interface as triggered by surface functionalization is only effective for the fully embedded nanofiller. This work provides a fundamental understanding of the mechanical properties of PVA nanocomposites reinforced by diamane, which can shed lights on the design and preparation of next generation high-performance nanocomposites.     

M1080B无心外圆磨床改进

M1080B无心外圆磨床砂轮及导轮宽度较窄,磨削轴承套圈外圆时,磨削效率低,托板架调整较为繁琐、皮带打滑、磨损较为严重。针对上述问题,提出了相应的解决办法,提高了磨削效率。     

埋地管道泄漏内封堵装置设计与研究

针对流体输送埋地管道泄漏问题,设计了一种利用管道机器人携带封堵气囊进行快速应急封堵修复的埋地管道泄漏内封堵装置。采用矩阵变换方法建立了牵引系统驱动轮过弯方程,利用MATLAB软件对过弯方程进行了验证,同时利用ADAMS软件仿真分析过弯路径与驱动轮转角对牵引系统行走速度的影响。研究结果表明:由两个串联封堵器组成的应急封堵系统可满足复杂工况下的管道泄漏封堵要求;牵引系统驱动轮在弯管内部行走时,单轮速度呈周期性变化,但三个驱动轮整体周期运动特性一致;驱动轮转角在25°~40°时,牵引系统行走速度与驱动轮转角成正比,且转角为30°时驱动效果最好。该内封堵装置的结构设计可为管道泄漏应急封堵领域装备的研发提供重要参考。     

Effect of grinding-induced cyclic heating on the hardened layer generation in the plunge grinding of a cylindrical component

This paper discusses the effects of the grinding-induced cyclic heating on the properties of the hardened layer in a plunge cylindrical grinding process on the high strength steel EN26. It was found that a multi-pass grinding brings about a uniform and continuous hardened layer along the circumference of the cylindrical workpiece. An increase of the number of grinding passes, leads to a thicker layer of hardening, a larger compressive residual stress and a deeper plastic deformation zone. Within the plastic deformation zone, the martensitic grains are refined by the thermo-mechanical loading, giving rise to a hardness of 12.5% higher than that from a conventional martensitic transformation. The coupled effects of heat accumulation and wheel wear in the multi-pass grinding are the main causes for the thickening of the hardened layer. A too small infeed per workpiece revolution would result in insufficient grinding heat, and in turn, bring about an undesirable tempered hardened layer and a reduction of its hardness.     

基于AFM的微结构加工实验研究

本文建立了微动工作台和原子力显微镜相结合的微加工系统，在该系统上采用金刚石针尖进行微加工实验，与SPI系统本身的刻划软件刻划出的图形进行了比较分析，得出这个系统适合微结构的加工；并给出了采用该方法加工的1111面及多边形面微结构；还分析了金刚石针尖几何角度及SPM和工作台的相关参数对加工的影响。     

预处理工艺对硬质合金与金刚石膜间粘结力的影响

在两种经不同预处理的硬质合金YG8基底上，采用微波等离子体化学气相沉积法，在微波功率2kW，压强4.0kPa和6.5kPa，CH4和H2流量分别为1.6cm/s和100.0cm/s的条件下生长金刚石薄膜。利用X射线衍射检测了金刚石薄膜是否存在，用拉曼光谱分析了薄膜的质量，用金相显微镜观察了薄膜的洛氏硬度压痕，标定并比较了不同预处理工艺膜与基底的结合力。实验结果表明，不同的预处理方法对于粘结力的影响不大，最主要的因素是钴含量的多少。     

金刚石膜的计算机虚拟制备技术中的分子动力学模拟

综述了近年来金刚石薄膜形成过程的分子动力学（Molecular Dynamics，简称MD）模拟研究，详细地阐述了原子间相互作用势的选取，总结了不同沉积条件下MD的计算模型和几种典型情况下的模拟结果。研究表明：在原子尺度上，MD方法能较全面地提供有关膜生长的信息，对进一步了解金刚石膜形成的微观机制以及为细观层次仿真提供基本信息均具有重要意义。     

铁路桥梁横向振动模拟及适应快速行车结构型式的研究

针对铁路提速后出现的上承式简支钢板梁桥跨中横向振幅过大的问题,以羊楼司桥(L=32m单跨上承式简支钢板梁桥)为例进行实桥检测和数值模拟,建立车辆、线路、桥梁三者的联合模型,考虑轮轨接触力,应用MSC/DYTRAN大型结构分析程序进行车线桥动力相互作用的仿真分析。研究揭示我国用量最多的C62型货车以70∽80km/h的速度空载通过时,该跨度的钢板梁桥发生横向谐振的机理。此外,用该方法对32m跨长的组合梁结构进行桥梁动力特性及列车走行性分析,表明该结构满足提速货车和高速电动旅客列车走行的要求。研究结果对我国高速铁路桥梁建设和既有桥梁的改造具有积极意义。     

Frequency weighting for the evaluation of steering wheel rotational vibration

The human perception of rotational hand–arm vibration has been investigated by means of a test rig consisting of a rigid frame, an electrodynamic shaker unit, a rigid steering wheel, a shaft assembly, bearings and an automobile seat. Fifteen subjects were tested while seated in a driving posture. Four equal sensation tests and one annoyance threshold test were performed using sinusoidal excitation at 18 frequencies in the range from 3 to 315 Hz. In order to guarantee the generality of the equal sensation data, the four tests were defined to permit checks of the possible influence of three factors: reference signal amplitude, psychophysical test procedure and temporary threshold shift caused by the test exposure. All equal sensation tests used a reference sinusoid of 63 Hz at either 1.0 or 1.5 m/s² r.m.s. in amplitude. The four equal sensation curves were similar in shape and suggested a decrease in human sensitivity to hand–arm rotational vibration with increasing frequency. The slopes of the equal sensation curves changed at transition points of approximately 6.3 and 63 Hz. A frequency weighting, called W_s, was developed for the purpose of evaluating steering wheel rotational vibration. The proposed W_s has a slope of 0 dB per octave over the frequency range from 3 to 6.3 Hz, a slope of −6 dB per octave from 6.3 to 50 Hz, a slope of 0 dB per octave from 50 to 160 Hz and a slope of −10 dB per octave from 160 to 315 Hz. W_s provides a possible alternative to the existing W_h frequency weighting defined in International Standards Organisation 5349-1 (2001) and British Standards Institution BS 6842 (1987).

Relevance to industry

For the manufacturers of tyres, steering systems and other vehicular components the proposed W_s frequency weighting provides a more accurate representation of human perception of steering wheel rotational vibration than the W_h weighting of ISO 5349-1 and BS6842.