Progressive damage modelling of SMC composite materials

The present work deals with the modelling of damage behaviour for sheet moulding compound (SMC) composite materials using a finite element analysis package. Specifically, a comparison is made between the results obtained experimentally for a three-point bending test, and those obtained from numerical simulation using a material model already implemented. The simulation has been performed for the material models available within the PAM-CRASH software. The simulation results are compared and validated with respect to experimentation.     

高抗挤厚壁套管的性能及应用效果评价

中原油田套管损坏的主要原因是现有套管强度不够,无法抵抗盐膏层段的巨大外挤力。开发了TP130TT型高抗挤厚壁套管,其强度能很好地抵抗盐膏层巨大外挤力。实验室试验表明,各项性能指标达到了设计要求,现场使用取得了很好的效果,解决了中原油田盐膏层段套管强度不足的难题。     

掺气减蚀保护作用的新概念

利用针式掺气流速仪测量原型和模型掺气浓度场、流速场，气泡尺寸及其概率分布的研究成果表明，原型水流韦伯数高，形成微小气泡的能力比模型强，气泡上浮慢，接近底部的小尺寸气泡概率及掺气浓度比模型大。初步研究认为：0.2mm或0.5mm以下的微小气泡在掺气减蚀中起着主要作用，可能只要很小掺气浓度即可达到掺气减蚀的效果。因此以小尺寸气泡的掺气浓度，作为判断掺气减蚀保护作用的指标将更为准确。     

低密度微泡沫压井液的研究与应用

吐哈油田部分区块地层压力系数小于0.9,常规水基压井液对储层伤害大,若使用油基压井液成本高,环境污染严重。通过实验优选出了一种低密度水基微泡沫压井液。该压井液具有密度低、泡沫强度高、稳定性好、携砂能力强等优点。现场应用表明,低密度微泡沫压井液稳定时间大于48 h,密度在0.70~0.99 g/cm3之间可调,抗油污染能力强,抗油大于8%,抗温在100℃以上,岩心污染后渗透率恢复值大于80%;并且施工方便,成本低,具有储层保护能力,使用微泡沫压井液的井表皮系数在0.20~2.34之间。     

A new monitoring system for piping systems in fossil fired power plants

A CEC-funded project has been performed to tackle the problem of producing an advanced Life Monitoring System (LMS) which would calculate the creep and fatigue damage experienced by high temperature pipework components. Four areas were identified where existing Life Monitoring System technology could be improved:

1. 1. the inclusion of creep relaxation

2. 2. the inclusion of external loads on components

3. 3. a more accurate method of calculating thermal stresses due to temperature transients

4. 4. the inclusion of high cycle fatigue terms.

The creep relaxation problem was solved using stress reduction factors in an analytical in-elastic stress calculation. The stress reduction factors were produced for a number of common geometries and materials by means of non-linear finite element analysis. External loads were catered for by producing influence coefficients from in-elastic analysis of the particular piping system and using them to calculate bending moments at critical positions on the pipework from load and displacement measurements made at the convenient points at the pipework. The thermal stress problem was solved by producing a completely new solution based on Green's Function and Fast Fourier transforms. This allowed the thermal stress in a complex component to be calculated from simple non-intrusive thermocouple measurements made on the outside of the component. The high-cycle fatigue problem was dealt with precalculating the fatigue damage associated with standard transients and adding this damage to cumulative total when a transient occurred.

The site testing provided good practical experience and showed up problems which would not otherwise have been detected.     

Suggestions for the quantitative X-ray microanalysis of thin sections of frozen-dried and embedded biological tissues

When a microregion in a thin section of frozen-dried and embedded tissue is analysed by the conventional electron-probe X-ray continuum-normalization method, the measured quantity is in mmol of element per kg of embedded specimen. As each microregion contains an unknown amount of embedding medium, this quantity generally lies indeterminately somewhere within the wide range between mmol of element per kg of hydrated tissue and mmol of element per kg of dehydrated tissue. However, if a ‘tag’ element is incorporated in the embedding medium, the contribution of the medium to the local continuum count in each probed field should be measurable, and the X-ray data may then unambiguously yield mmol of element per kg of dehydrated tissue. This result should not be affected by shrinkage on freeze-drying or by incomplete replacement of water by embedding medium. The same X-ray data can additionally provide estimates of mmol of element per unit volume, mmol of element per kg of hydrated tissue and local dry-mass fraction. However, these estimates are subject to errors due to tissue shrinkage, incomplete replacement of water and beam damage.     

A One-Dimensional Nonlocal Damage-Plasticity Model for Ductile Materials

This paper presents a new 1-D non-local damage-plasticity deformation model for ductile materials. It uses the thermodynamic framework described in Houlsby and Puzrin (2000) and holds, nevertheless, some similarities with Lemaitre’s (1971) approach. A 1D finite element (FE) model of a bar fixed at one end and loaded in tension at the other end is introduced. This simple model demonstrates how the approach can be implemented within the finite element framework, and that it is capable of capturing both the pre-peak hardening and post-peak softening (generally responsible for models instability) due to damage-induced stiffness and strength reduction characteristic of ductile materials. It is also shown that the approach has further advantages of achieving some degree of mesh independence, and of being able to capture deformation size effects. Finally, it is illustrated how the model permits the calculation of essential work of rupture (EWR), i.e. the specific energy per unit cross-sectional area that is needed to cause tensile failure of a specimen.     

降低气体悬浮焙烧炉焙烧过程中Al_2O_3粒度破损的措施

为了降低气体悬浮焙烧炉焙烧过程中Al_2O_3粒度的破损,对气体悬浮焙烧炉焙烧过程中氧化铝粒度的影响因素进行了分析,提出了降低粒度破损的一些措施。     

Oxygen content of the fixative is important in the interpretation of the ultrastructure of ischaemic myocardium

Isolated rat hearts were subjected to 15, 45, or 60 minutes of global ischaemia and then fixed by perfusion at 37°C with glutaraldehyde containing various amounts of oxygen. This either had been bubbled with 100% oxygen (PO₂ 620 mm Hg) or with 100% nitrogen (PO₂ 40 mm Hg) immediately before use, or it had been routinely prepared and stored exposed to atmospheric oxygen (PO₂ 245 mm Hg). The ultrastructure of myocytes and endothelial cells subjected to 15 minutes of ischaemia was not affected by the treatment of the fixative. However, when the tissue subjected to longer periods of ischaemia was fixed with routinely prepared or oxygen-bubbled glutaraldehyde, ultrastructural changes characteristic of reoxygenation damage were uniformly evident in both the microvasculature and myocytes. These qualitatively distinct changes included mitochondrial swelling, cell swelling, endothelial bleb formation, and narrowing of capillary lumina. These abnormalities were not observed in tissue fixed with nitrogen-bubbled glutaraldehyde. These findings indicate that deliberate steps should be taken to reduce or eliminate dissolved oxygen from the fixatives used to study ischaemic tissues. Otherwise artefactual reoxygenation damage in vitro may occur and make valid ultrastructural interpretation difficult or impossible.     

Self-Irradiation Cascade Simulations in Plutonium Metal: Model Behavior at High Energy

The Modified Embedded Atom Method model for Pu metal is revised so that it more accurately captures the behavior of the Ziegler-Biersack-Littmark model of ion-ion interactions. Two revision are tested with somewhat different stiffnesses in the 2-1000 eV range. The revised models show higher damage levels at 20 KeV than an earlier model, suggesting that the behavior of the models above 100 eV is dominating damage production, at least in the earlier stages of the cascade. Work was performed at Los Alamos National Laboratory under the auspices of the US Department of Energy, under contract DE-AC52-06NA25396.