高等级生物安全实验室通风空调系统冗余设计原则探讨

对比分析了国内外标准有关高等级生物安全实验室通风空调系统冗余设计的要求。结合我国已有高等级生物安全实验室,重点分析了送风机、排风机、排风高效过滤器冗余设计的具体实施形式和存在的问题,给出了冗余设计原则建议。     

排风扇前盖注射模设计

分析了排风扇前盖塑件的工艺特点,介绍了排风扇前盖注射成型模结构及模具的工作过程。     

GK1C型内燃机车频繁停车现象探讨与解决方案

运用过程中各类相关因子的变化,会使得机车柴油机配气相位出现一定程度变化,采取某种措施调整或是处理可以解决动力不足的问题。     

CO2 abatement and CH4 recovery at vehicle exhausts: Comparison and characterization of Ru powder and pellet catalysts

The catalytic conversion of CO₂ to CH₄ (Sabatier reaction) has been studied to develop an after-treatment process at vehicles exhausts. Three different formulations of Ru commercial catalysts, two in powder and one in pellets shape, were tested and characterized by means of X-ray powder diffraction, scanning electron microscopy (SEM-EDX), N₂ adsorption at −196 °C and temperature-programmed reduction (TPR).Experimental results show a high CO₂ conversion (X_CO2 = 0.96 @ T = 280 °C) for one powder catalyst formulation whereas the other one has maximum CO₂ conversion = 0.69. In both cases a high CH₄ selectivity is measured. High CO₂ conversion (X_CO2 = 0.92 @ T = 300 °C) is obtained also with pellet catalysts but only at lower GHSV values. The different behavior of the catalysts was ascribed to the different physicochemical properties and the key parameters for the application development of the process were identified. In particular, the possibility to use pellets or monolithic reactors, thus minimizing the pressure drops in the reactor, makes possible a commercial application in the treatment of vehicles exhausts.     

采油树平板闸阀柔性密封圈结构优化设计

为了提高采油树平板闸阀密封圈的密封性能,在泛塞封的基础上,设计一种密封圈本体唇边开有锯齿状凸起的新型柔性密封结构;运用有限元分析方法模拟密封圈的工作状况,分析柔性密封结构特性参数对密封圈密封性能的影响,获得不同柔性密封圈结构参数下密封面间接触应力分布规律,并对新型密封结构进行优化。结果表明:密封面间最大接触应力随唇边锯齿数量、唇边夹角度数的增大而增大,随唇谷夹角度数的增大而减小;新型密封结构选择锯齿数量为3、唇边夹角为20°、唇谷夹角为30°的特性参数时,其最大接触应力比常规Y形密封圈提高了15倍;新型柔性密封结构的密封圈与阀杆、阀盖壁面间接触应力比常规Y形密封圈有显著提高,提高了密封圈的密封性能。     

抽油井不压井作业装置及抽油泵底阀设计

江苏油田的部分油井存在油管短路、地层高压低渗、漏失严重等问题,这些问题造成压井作业困难,并且压井作业过程中的井控与环境污染风险较大。为了进行不压井检泵作业,同时缩短检泵之后的产量恢复周期,进行了不压井作业技术研究,并研制了不压井作业装置。为解决起下抽油杆过程中的防喷问题,改进了抽油泵底阀结构,该结构可实现起下抽油杆过程中油管不带压、无溢流,并保障起下油管过程中的井控安全。该技术在江苏油田现场应用9井次,效果良好。     

光照水电站装设筒形阀分析

筒形阀是一种新型的水轮机进水阀,它与球阀或蝴蝶阀相比较有防止机组飞逸事故扩大效果明显、减轻导叶全关时导水机构的快速破坏并减少漏水量,以及动水开启方便、所需时间短等优点,但对运行条件也有一定的要求。光照水电站是贵州省第1个拟采用筒形阀的电站,为此对装设筒形阀的可行性和必要性进行了认真的分析。     

试油井选层压裂新工艺及现场试验

设计新型可洗井封隔器，保障油井有反洗井通道，有效防止封隔器以上砂埋所引发的管柱砂卡事故，并对新型封隔器、控制开关、密封接头、同心大通径压力计托筒等井下工具组合优化。解决了多层油井任意选层压裂、求产、测井温一体化的难题。     

双缸式气动-手动楔式闸阀在柴油罐上的应用

文章简单介绍了气动阀的结构、工作原理及特点,并时堆修保养注意事项以及可能发生的故障和排除故障的方法做了详细讲解。最后,将气动阀在柴油罐上的应用情况与普通闸阀相比较,分析其使用性能和优点,进一步推广气动闽在锦西石化分公司的应用。     

Performance of thermostatic and electronic valves controlling the compressor capacity

The performance of the energy consumption of an electronic valve and a classical thermostatic valve has been compared when these expansion valves are adopted in a vapour compression plant subjected to a cold store. The main aim is to verify experimentally which type of expansion valve would be preferable from energy point of view when a classical thermostat or a fuzzy logic algorithm are used as the control system for the refrigeration capacity. The fuzzy logic‐based control is able to modulate continuously the compressor speed through an inverter. The results show that with a fuzzy algorithm, the thermostatic expansion valve allows an energy saving of about 8% in comparison with the electronic valve. When on–off control is used, the electric energy consumption obtained both with the electronic valve and with the thermostatic valve is comparable. Copyright © 2006 John Wiley & Sons, Ltd.