Numerical approach to analyze fluid flow in a type C tank for liquefied hydrogen carrier (part 1: Sloshing flow)

The demand for clean energy use has been increasing worldwide, and hydrogen has attracted attention as an alternative energy source. The efficient transport of hydrogen must be established such that hydrogen may be used as an energy source. In this study, we considered the influences of various parameters in the transportation of liquefied hydrogen using type C tanks in shipping vessels. The sloshing and thermal flows were considered in the transportation of liquefied hydrogen, which exists as a cryogenic liquid at ?253 °C. In this study, the sloshing flow was analyzed using a numerical approach. A multiphase sloshing simulation was performed using the volume of fluid method for the observation and analysis of the internal flow. First, a sloshing experiment according to the gas-liquid density ratio performed by other researchers was utilized to verify the simulation technique and investigate the characteristics of liquefied hydrogen. Based on the results of this experiment, a sloshing simulation was then performed for a type C cargo tank for liquefied hydrogen carriers under three different filling level conditions. The sloshing impact pressure inside of the tank was measured via simulation and subjected to statistical analysis. In addition, the influence of sloshing flow on the appendages installed inside of the type C tank (stiffened ring and swash bulkhead) was quantitatively evaluated. In particular, the influence of the sloshing flow inside of the type C tank on the appendages can be utilized as an important indicator at the design stage. Furthermore, if such sloshing impact forces are repeatedly experienced over an extended period of time under cryogenic conditions, the behavior of the tank and appendages must be analyzed in terms of fatigue and brittle failure to ensure the safety of the transportation operation.     

综放工作面防治水技术应用实践

为解决21000工作面采空区及顶板涌水问题,根据工作面出水点的不同情况,采取了集水器导水、老塘设挡水堰截水、挖排水沟疏水等多项治水措施,经统计排水量达33~42m3/h,有效控制了水情,确保了工作面正常生产。     

葛洲坝水利枢纽泄水建筑物进水口冲磨与修复

葛洲坝水利枢纽工程已运行20余年，近年水下检查中发现泄水建筑物进水口存在不同程度的冲磨，有些已威胁到建筑物安全运行，分析冲磨原因和探讨修复材料和手段是非常重要的，本文就此问题提出一些看法和建议供参考。     

轻质滤料滤池的试验与研究

轻质滤料滤池是以比水密度略小的滤料为滤床的滤池，通过以净水厂的原水和污水处理厂的二级处理出水为过滤试验对象，所取得的结果表明：下向流轻质滤料滤池对浊度和悬浮固体（SS）的去除率分别可以达到80％和45％，而滤床的水头损失不超过15cm。因此轻质滤料滤池可以以预过滤的形式配置在过滤处理的净水和污水的处理工艺中。     

光纤光栅感温火灾探测报警系统在原油罐区的应用

通过对现有罐区火灾自动报警技术的认真考察、对比,在石西集中处理站原油罐区安装了光纤光栅感温火灾探测报警系统.该报警系统的传感信号是光的波长变化,传感器及其探测系统是靠光缆连接而进入被测现场,它具有高安全性、高可靠性、高绝缘性、高抗电磁干扰性、防潮耐蚀、寿命长等其他传统火灾探测报警系统无法比拟的优越性能.阐述了其系统构成和运行效果.该系统在石西集中处理站运用效果良好.     

炼油厂成品油罐区调度优化问题研究

研究了以集合论为基础的调度优化模型。给出了该离散型优化问题的求解算法。根据优化结果，在G2实时智能平台上开发了包含监视子系统和调度子系统的调度支持系统。在中国石化股份有限公司长岭分公司的试用结果表明，该调度系统可以提高炼油厂的生产效率，从而提高炼油厂的经济效益。     

板式塔中无伸缩型受液槽的改进

对板式塔中的受液槽进行了改进，将无伸缩型改性伸缩型，避免了漏液，提高了常压塔的分离效果。     

换热器小浮头螺栓断裂失效分析

针对换热器小浮头螺栓发生断裂的情况进行失效分析，找出原因，提出处理措施及材质选择时应注意的问题。