基于滚动摩擦作用下玉米颗粒在模拟筒仓卸料中的力链分析（网络首发、推荐阅读）

针对颗粒滚动摩擦作用对筒仓中玉米颗粒的力链空间分布进行研究，通过EDEM离散元软件建立筒仓模型与仿真玉米颗粒模型进行卸粮仿真模拟，并与筒仓卸料实验作流态对比，验证模型与仿真结果的准确性。通过对模拟仓进行切片观察和数据处理，对比分析了不同摩擦情况下力链的细观参数随时间演化规律。模拟结果表明：颗粒间摩擦系数越大，卸粮完成的最终时间越长；颗粒间滚动摩擦系数越小，颗粒由整体流转变为管状流的时间越早。对于有漏斗的筒仓来说，减小颗粒间摩擦会改变整体流和管状流之间的极限，从而增加产生管状流的面积。标准滚动摩擦系数下玉米颗粒在卸料过程中会出现起拱-塌陷效应；减小滚动摩擦，玉米颗粒卸料较稳定，未出现起拱的应力突增、以及拱塌陷的应力衰减；增大颗粒间滚动摩擦不但会增加拱效应，且出现成拱高度距离漏斗口更高。     

Superswelling Microneedle Arrays for Dermal Interstitial Fluid (Prote)Omics

The noninvasive sampling of dermal interstitial fluid (ISF) for the monitoring of clinical biomarkers is a greatly appealing area of research. The identification of molecular biomarkers in biological fluids has been accelerated with -omics analyses but remains limited in ISF because of its time-consuming and complex extraction process. Here, the generation of microneedle (MN) patches made of superabsorbent acrylate-based hydrogels for the rapid sampling of dermal ISF is described to explore its proteome. In depth, iterative optimization allows the identification of novel acrylate-based compositions with the required chemical, mechanical, and biocompatibility properties allowing proteomic analysis of the extracted ISF for the first time after sampling with swelling MNs. The generated MN arrays show no cytotoxic effect, successfully cross the stratum corneum, and can collect up to 6 µL of dermal ISF in 10 min in vivo. Proteomics lead to the detection of 176 clinically relevant biomarkers in the collected samples validating the use of ISF as a relevant bodily fluid for disease monitoring and diagnostic. Importantly, it is discovered that extraction fingerprint is strongly dependent on the MNs chemistry, and thus specific biomarkers could be selectively extracted by tuning the composition of the patch, making the system versatile and specific.     

Ablation behavior of thin-blade co-deposited C/Cx-SiCy composites under the influence of the complex fluid conditions of the oxyacetylene torch

This paper offers a new way of testing the ablation property of material under an oxyacetylene torch using a thin-blade specimen, which costs much less time to reach the maximum temperature and provides a harsh turbulence fluid field that's closer to reality. The thin-blade specimen experiences a higher turbulent intensity than the traditional disk-like specimen, leading to more efficient heat exchange. The fluid field simulation agrees with the testing results. In addition, we manage to synthesize the C/Cx-SiCy composites with the co-deposition chemical vapor infiltration (CVI) method. The C/Cx-SiCy composites exhibit a similar anti-ablation property as C/C composites and consist of enough SiC phase simultaneously, combining the advantages of both C/C composites and C/SiC composites. The thin-blade C/Cx-SiCy composites show a lower linear ablation rate (1.6 μm/s) than C/C composites (4.1 μm/s) and C/SiC composites (19.6 μm/s) during the oxyacetylene test. The glass layer formed on the surface of C/Cx-SiCy could cling to the bulk material instead of peeling off due to the high PyC content in the matrix could protect the SiO₂ from blowing away.     

Optimization of flow in additively manufactured porous columns with graded permeability

Chemical engineering systems often involve a functional porous medium, such as in catalyzed reactive flows, fluid purifiers, and chromatographic separations. Ideally, the flow rates throughout the porous medium are uniform, and all portions of the medium contribute efficiently to its function. The permeability is a property of a porous medium that depends on pore geometry and relates flow rate to pressure drop. Additive manufacturing techniques raise the possibilities that permeability can be arbitrarily specified in three dimensions, and that a broader range of permeabilities can be achieved than by traditional manufacturing methods. Using numerical optimization methods, we show that designs with spatially varying permeability can achieve greater flow uniformity than designs with uniform permeability. We consider geometries involving hemispherical regions that distribute flow, as in many glass chromatography columns. By several measures, significant improvements in flow uniformity can be obtained by modifying permeability only near the inlet and outlet.     

Estimation of gradient size of interfacial strain and its optimization for effective magnetoelectric coupling in (CoFe2O4) – (0.93Na0.5Bi0.5TiO3 – 0.07BaTiO3), 2-2 nano-composites

Strain-mediated coupling between the magnetic and electrically ordered phases plays a significant role in magnetoelectric (ME) nano-composites. This study explores a method to analyse and quantify interfacial strain using a grazing angle scan (α) in a ME composite optimised for a specific microstructure. The details of strain around the interface CoFe₂O₄ (CFO) – 0.93Na_0.5Bi_0.5TiO₃ – 0.07BaTiO₃ (NBT-BT) was determined by performing ‘α’ scan, in order to gather information at various depths of the NBT-BT layer around maximum intensity (110) reflection. The strain around the interface was observed to dominate over a spatial region of ～20–30 nm away from the interface. The Piezoresponse force microscopy (PFM) studies performed near the interface reveal that the strain constrain experienced by the ferroelectric layer operates such that polarisation rotation and domain wall motion are constrained compared to the strain relaxed region of the film. For effective strain transfer, heterostructures grown with optimised thicknesses (～20–30 nm) exhibited a superior inverse piezomagnetic effect.     

Designing amorphous formulations of polyphenols with naringin by spray-drying for enhanced solubility and permeability

Naringin (NAR), a major flavanone (FVA) glycoside, is a component of food mainly obtained from grapefruit. We used NAR as a food additive to improve the solubility and permeability of hydrophobic polyphenols used as supplements in the food industry. The spray-dried particles (SDPs) of NAR alone show an amorphous state with a glass transition temperature (T_g) at 93.2 °C. SDPs of hydrophobic polyphenols, such as flavone (FVO), quercetin (QCT), naringenin (NRG), and resveratrol (RVT) were prepared by adding varying amounts of NAR. All SDPs of hydrophobic polyphenols with added NAR were in an amorphous state with a single T_g, but SDPs of hydrophobic polyphenols without added NAR showed diffraction peaks derived from each crystal. The SDPs with NAR could keep an amorphous state after storage at a high humidity condition for one month, except for SDPs of RVT/NAR. SDPs with NAR enhanced the solubility of hydrophobic polyphenols, especially NRG solubility, which was enhanced more than 9 times compared to NRG crystal. The enhanced solubility resulted in the increased membrane permeability of NRG. The antioxidant effect of the hydrophobic NRG was also enhanced by the synergetic effect of NAR. The findings demonstrated that NAR could be used as a food additive to enhance the solubility and membrane permeability of hydrophobic polyphenols.     

Evaluation of hydrodynamic behavior of the perforated gas distributor of industrial gas phase polymerization reactor using CFD-PBM coupled model

A 2D computational fluid dynamics (Eulerian–Eulerian) multiphase flow model coupled with a population balance model (CFD-PBM) was implemented to investigate the fluidization structure in terms of entrance region in an industrial-scale gas phase fluidized bed reactor. The simulation results were compared with the industrial data, and good agreement was observed. Two cases including perforated distributor and complete sparger were applied to examine the flow structure through the bed. The parametric sensitivity analysis of time step, number of node, drag coefficient, and specularity coefficient was carried out. It was found that the results were more sensitive to the drag model. The results showed that the entrance configuration has significant effect on the flow structure. While the dead zones are created in both corners of the distributors, the perforated distributor generates more startup bubbles, heterogeneous flow field, and better gas–solid interaction above the entrance region due to jet formation.     

Upscaled DEM-CFD model for vibrated fluidized bed based on particle-scale similarities

Simulation based on discrete element method (DEM) coupled with computational fluid dynamics (CFD), coupled DEM-CFD, is a powerful tool for investigating the details of dense particle–fluid interaction problems such as in fluidized beds and pneumatic conveyers. The addition of a mechanical vibration to a system can drastically alter the particle and fluid flows; however, their detailed mechanisms are not well understood. In this study, a DEM-CFD model based on a non-inertial frame of reference is developed to achieve a better understanding of the influence of vibration in a vibrated fluidized bed. Because the high computational cost of DEM-CFD calculations is still a major problem, an upscaled coarse-graining model is also employed. To realize similar behaviors with enlarged model particles, non-dimensional parameters at the particle scale were deduced from the governing equations. The suitability and limitations of the proposed model were examined for a density segregation problem of a binary system. To reduce the computational costs, we show that the ratio between the bed width and model particle size can be reduced to a minimum value of 100; to obtain similar segregation behaviors, the ratio between the bed height and model particle size is considered unchanged.     

表面活性剂对低渗透油藏渗吸的影响

采用不同类型的表面活性剂进行自发渗吸实验,并对表面活性剂改善岩石润湿性、降低界面张力的能力进行了分析。实验结果表明,阴离子型表面活性剂改善润湿性的能力好于其他类型的表面活性剂,且在岩心中的自发渗吸效果最好,这是由于阴离子型表面活性剂改善润湿性的机理为离子对形成机理,强于阳离子的吸附机理;接触角是决定渗吸能否发生的决定性因素,只有接触角小于70°时渗吸才能发生;界面张力影响渗吸速度和最终采出程度,对于渗透率为1 mD的岩心,最佳界面张力为10~(-1) mN/m。