交流伺服系统在玻璃裂片机中的应用

随着运动控制技术的飞速发展，交流伺服系统应用的日益广泛。介绍了液晶生产中的关键设备玻璃裂片机，并详细分析松下MINAS A系列交流伺服系统在玻璃裂片机中的应用。     

Performance of thermostatic and electronic valves controlling the compressor capacity

The performance of the energy consumption of an electronic valve and a classical thermostatic valve has been compared when these expansion valves are adopted in a vapour compression plant subjected to a cold store. The main aim is to verify experimentally which type of expansion valve would be preferable from energy point of view when a classical thermostat or a fuzzy logic algorithm are used as the control system for the refrigeration capacity. The fuzzy logic‐based control is able to modulate continuously the compressor speed through an inverter. The results show that with a fuzzy algorithm, the thermostatic expansion valve allows an energy saving of about 8% in comparison with the electronic valve. When on–off control is used, the electric energy consumption obtained both with the electronic valve and with the thermostatic valve is comparable. Copyright © 2006 John Wiley & Sons, Ltd.     

欠平衡钻井过程中的井控新设备

文章简述了欠平衡钻井中不压井操作的设备和方法,介绍了威得福公司的井下套管阀和海底泥浆举升钻井工业联合项目在深水钻井中研发的新钻杆阀在欠平衡钻井中的应用。通过在钻杆上安装钻杆阀和在套管上安装套管阀解决接单根及起下钻操作时因压井可能破坏欠平衡状态的问题,使全过程的欠平衡钻井得以实现。     

Electrochemical mass transfer between an impinging jet and a rotating disk in a confined system

This paper presents the mass transfer results from an impinging liquid jet to a rotating disk. The mass transfer coefficients were measured using the electrochemical limiting diffusion current technique (ELDCT). Rotational Reynolds number (Re_r) in the range of 3.4 × 10⁴–1.2 × 10⁵, jet Reynolds number (Re_j) 1.7 × 10⁴–5.3 × 10⁴ and non-dimensional jet-to-disk spacing (H/d) 2–8 were taken into consideration as parameters. It was found that the jet impingement resulted in a substantial enhancement in the mass transfer compared to the case of the rotating disk without jet.     

Eigenspannungen als Messgröße zur Qualitätssicherung

Residual stress as measured quantity in quality assurance The x‐ray method is used in the Volkswagen Automotive Group at different world‐wide locations as a standard procedure to determine residual stress. As an important measured quantity in the quality assurance residual stresses are specified in drawings of different components (e.g. gears, coil springs). Measurements are carried out during quality assurance, production, damage analyse, technical development department and design control of components from suppliers. An optimum efficiency can be achieved, if it exists a unique correlation between residual stress values and loading capacity of components, and if the processes to introduce residual stress can be optimized using residual stress measurements during the production.     

蓄热式均热炉生产中存在问题的分析及解决方案

介绍了高温空气燃烧技术在均热炉上的应用情况，对应用中出现的问题进行了分析，并提出了解决方案。     

CPLD在雷达伺服轴角编码电路中的应用

介绍一种针对正、余弦旋转变压器—数字转换器(RDC)模块，用复杂可编程逻辑器件(CPLD)技术实现伺服轴角编码电路设计的方案。分析了轴角编码器系统中14XSZ系列旋转变压器—数字转换器的原理、轴角粗精组合原理及轴角纠错原理。详细介绍了CPLD的内部功能电路、CPLD轴角粗精组合和纠错实现电路，以及CPLD的工作时序图。提出了利用CPLD实现轴角粗精组合处理的方案，并通过了实际系统运行的考验，证明该方案可行。     

液晶光阀光电导层光吸收系数的研究

用化学气相沉积法制备了液晶光阀中光电导层———非晶硅薄膜,从实验中得出最佳制备工艺的参数取值。给出了用包络线法测量非晶硅薄膜光吸收系数的原理,测量了样品的光吸收系数随波长的变化规律。得到样品在最佳工艺条件下的光吸收系数高于1×103cm-1。     

电接点压力表补水泵定压系统的应用

阐述了电接点压力表补水泵定压系统的一些应用问题 ,给出了电接点压力表定压点的上、下限计算公式 ,并提出了该系统补给水泵、补给水箱及安全阀的设计选型方法