The influence of volume fraction of amorphous phase on corrosion resistance of Mg67Zn 29Ca 4 alloy

The aim of this study was to investigate the structure and corrosion resistance of amorphous, amorphous‐crystalline, and crystalline Mg₆₇Zn₂₉Ca₄ alloy for biodegradable applications. This paper presents a preparation method and results of the structural characterization and corrosion resistance analysis of the material. Samples were prepared in the form of 3 mm diameter rods. The structure of the alloy was examined with the use of X‐ray diffractometry and scanning electron microscopy. The thermal properties of the samples were examined with differential scanning calorimetry (DSC). Results of DSC analysis were used to determine heat treatment temperatures, allowing to obtain different fractures of crystalline phase in the material. Corrosion resistance of heat‐treated samples was investigated by immersion tests and electrochemical measurements performed in the simulated body fluid. The X‐ray diffraction results confirmed that the prepared Mg₆₇Zn₂₉Ca₄ alloy's structure is fully amorphous. After heat treatment, samples with different fractions of amorphous phase in the structure were obtained. Immersion tests of the samples showed that the structure significantly influenced corrosion resistance in examined materials. It should be pointed out, that certain amounts of crystalline phase in amorphous matrix can greatly improve the corrosion resistance of Mg₆₇Zn₂₉Ca₄ alloy.     

Nature of heterophase inclusions in high-purity optical fiber materials as studied with 3D laser ultramicroscopy

3D laser ultramicroscopy (3D LUM) is intended specially for determining the concentration and size distribution of submicron inclusions in the bulk samples of high-purity materials for visible and IR fiber optics. In this work the 3D LUM technique is shown to be able to identify the nature of individual inclusions detected. The measurement of the light scattered by an inclusion at a varied probe beam wavelength and polarization and at a varied scattered light collection angle makes it possible to determine the inclusion refractive index. The 3D LUM possibilities are illustrated by the example of studying the inclusion nature in the As₂S₃ glass samples prepared by the direct synthesis from elements in a quartz container at elevated temperatures.     

Tribological behavior of Zr-based bulk metallic glass sliding against polymer,ceramic, and metal materials

The tribological properties of zirconium-based bulk metallic glass (BMG) sliding against polymers, steels, and ceramics at different loads and speeds were investigated. Acoustic emission (AE) technology was used to analyze wear states. The frictional coefficients of the BMG slid against the steel and ceramic balls were high but decreased with increased applied normal load and sliding speed. As the steel balls were more ductile than the ceramic ones, the steel–BMG sliding pairs generated weaker AE signals and exhibited larger wear rates. The BMG tested against the polymer balls had much lower and more stable frictional coefficients than the ones against the steel or ceramic balls because of transferred polymer layers on the BMG surfaces. The BMG against the polymer balls also exhibited the highest AE signals among the three types of counter materials used, indicating that abrasive wear dominated in the polymer-BMG sliding pairs. These results demonstrated the potential application of the BMG as a new tribomaterial that could be an alternative to the traditional crystalline metals for various counter materials.     

机械合金化Fe-Ni粉末的相结构

使用XRD和Moessbauer等方法，研究了在Ar气氛下机械合金化Fe—Ni粉末相结构的变化．结果表明，在机械合金化Fe64-Ni36粉末过程中，fcc相的数量随着球磨时间的增加先增加然后减少，与加乙醇球磨Fe64-Ni36的情形相同．当Ni的含量(原子分数)大于50％时，有fcc相、顺磁相和FeNi3形成，当Ni的含量低于50％时，bcc相的数量随着Ni含量减少而增加．Moessbauer谱的结果表明，因球磨时间或Fe、Ni比例的不同，Fe—Ni球磨粉末固溶体具有不同结构的原子配比。     

大块非晶合金的性能、制备及应用

综述了大块非晶合金的性能、制备方法及应用，对比了吸铸法制备的棒状Zr41.2Ti13.8Cu12.5Ni10Be22.5,Zr57Cu20Al10Ni8Ti5,Zr52.5Ti5Cu17.9Ni14.6Al10(原子分数)大块非晶样品的过冷温度区间宽度(△Tx)，给出了3种大块非晶合金系列的热稳定性参数Tg、Tx及△Tx，提出了大块非晶合金领域存在的问题及发展方向．     

Physical Aging of Amorphous Fructose

ABSTRACT: Physical aging of amorphous anhydrous fructose at temperature 5 °C and at 22 °C was studied using differential scanning calorimetry (DSC). The dynamic glass transition temperature, T_g0 for unaged samples was 16 °C and 13.3 °C for heating rate of 10 °C/min and 1 °C/min, respectively. The fictive temperature, T_f0 for unaged samples calculated by Richardson and Savill method was 12 °C, which is close to the dynamic value obtained from the lower DSC heating rate. The fictive temperature T_f of the aged fructose glasses at temperatures both below and above the transition region was fitted well by a non-exponential decay function (Williams-Watts form). Aging above the transition region (22 °C) for 18 d increased both the dynamic glass transition temperature T_g and the fictive temperature T_f. However, aging below the transition region (5 °C) for 1 d increased the dynamic glass transition temperature T_g but decreased the fictive temperature T_f.     

A One-Dimensional Nonlocal Damage-Plasticity Model for Ductile Materials

This paper presents a new 1-D non-local damage-plasticity deformation model for ductile materials. It uses the thermodynamic framework described in Houlsby and Puzrin (2000) and holds, nevertheless, some similarities with Lemaitre’s (1971) approach. A 1D finite element (FE) model of a bar fixed at one end and loaded in tension at the other end is introduced. This simple model demonstrates how the approach can be implemented within the finite element framework, and that it is capable of capturing both the pre-peak hardening and post-peak softening (generally responsible for models instability) due to damage-induced stiffness and strength reduction characteristic of ductile materials. It is also shown that the approach has further advantages of achieving some degree of mesh independence, and of being able to capture deformation size effects. Finally, it is illustrated how the model permits the calculation of essential work of rupture (EWR), i.e. the specific energy per unit cross-sectional area that is needed to cause tensile failure of a specimen.     

锌电积的节电探讨

分析厂影响锌电积电能消耗的因素，提出了锌电积的节电对策与展望。     

Solid State Concepts to Understand Catalysis Using Nanoscale Metallic Particles

New advances in theoretical background and recent experimental results concerning nanometer scale metallic clusters are presented. We will begin by a presentation of the advantages and the limitations of synchrotron radiation techniques to characterise nanometer scale entities. Then, through a review of recent papers, we try to make a link between metallic surfaces and nanometer scale monometallic clusters in the case of the interaction with a small molecule, namely NO.     

金属矿山当前面临的主要问题及对策

叙述了为了解我国金属矿山当前面临的突出问题，必须充分依靠科技进步和技术创新，大力提高矿山企业的技术水平，装备水平和管理水平。