土的最大干密度和最优含水率快速测定法

对快速击实试验研究成果进行了总结,并介绍了应用快速击实试验研究成果的经验.不论是重型击实还是轻型击实,也不论击实试验所给定的击实功能多大,应用"一点法"或"快速法"击实试验原理,对土料都有一定要求."一点法"击实试验与快速击实试验所用土体的比重在2.67～2.73之间,当被测土样的比重超越此范围时,在绘制击实曲线时可适当偏离ρdmax计算值的点,但这个误差是很小的,通常ρdmax的影响在±0.01 g/cm3以内,而对ωop的影响在±0.5%以内.结合工程实例,对击实试验成果的简化校正作了详细介绍.     

Density Measurement of Liquid Ni-Ta Alloys by a Modified Sessile Drop Method

The density of liquid Ni- Ta alloys was measured by using a modified sessile drop method. It is found that the density of the liquid Ni- Ta alloys decreases with the increasing temperature, but increases with the increase of tantalum concentration in the alloys. The molar volume of liquid Ni- Ta binary alloys increases with the increase of temperature ancl tantalum concentration.     

Volumetric properties of mixtures of 1,4-dioxane and water at high pressures

Densities of aqueous of 1,4-dioxane have been measured at temperatures from 298 to 348 K and at pressures up to 40 MPa by a vibrating-tube method. Molar volumes obtained with an estimated uncertainty of ±0.2°,% are correlated with pressure by the Tait equation within the experimental uncertainty. Pressure and composition dependences of the excess molar volume, partial molar volume, and isothermal compressibility are determined and they are compared with those of other aqueous solutions.     

Analysis of supersaturation and nucleation in a moving solution droplet with flowing supercritical carbon dioxide

A supercritical antisolvent (SAS) process is employed for production of solid nanoparticles from atomized droplets of dilute solution in a flowing supercritical carbon dioxide (SC CO₂) stream by attaining extremely high, very rapid, and uniform supersaturation. This is facilitated by a two‐way mass transfer of CO₂ and solvent, to and from the droplet respectively, rendering rapid reduction in equilibrium solubility of the solid solute in the ternary solution. The present work analyses the degree of supersaturation and nucleation kinetics in a single droplet of cholesterol solution in acetone during its flight in a flowing SC CO₂ stream. Both temperature and composition are assumed to be uniform within the droplet, and their variations with time are calculated by balancing the heat and mass transfer fluxes to and from the droplet. The equilibrium solubility of cholesterol with CO₂ dissolution has been predicted as being directly proportional to the Partial Molar Volume Fraction (PMVF) of acetone in the binary (CO₂–acetone) system. The degree of supersaturation has been simulated up to the time required to attain almost zero cholesterol solubility in the droplet for evaluating the rate of nucleation and the size of the stable critical nuclei formed. The effects of process parameters have been analysed in the pressure range of 7.1–35.0 MPa, temperature range of 313–333 K, SC CO₂ flow rate of 0.1136–1.136 mol s^?1, the ratio of the volumetric flow rates of CO₂‐to‐solution in the range of 100–1000, and the initial mole fraction of cholesterol in acetone solution in the range of 0.0025–0.010. The results confirm an extremely high and rapid increase in degree of supersaturation, very high nucleation rates and stable critical nucleus diameter of the order of a nanometre. Copyright © 2005 Society of Chemical Industry     

Synthesis and Evaluation of Blends Formed by Polymeric Crown Ethers and a Fullerene-Containing Primary Ammonium Salt in Organic Thin Films

The synthesis of a series of polymers and cyclopolymers bearing crown ethers of differing structure and affinities towards primary ammonium ions is discussed. These polymers have been tested in their efficiency to form structurally homogeneous thin films when blended with an amphiphilic C₆₀ compound containing a primary ammonium ion functional group. The X-ray reflectivity characterization of the films revealed that the polymer bearing the crown ether with the least affinity for primary ammonium ions, but having the highest degree of polymerization, is the most effective in forming structurally homogeneous thin films.     

热带钢连轧机工作辊温度场和热凸度预报模型

采用一种具有较高精度的样条有限条法对轧制过程中工作辊的温度场和热凸度进行计算和预报。结果证明，该模型理论计算值与现场实测值吻合较好，可以较准确地计算和预报热带钢连轧机工作辊的热凸度。     

A method of estimating the standard gibbs free energy of formation

Standard Gibbs free energy of formation (ΔG_f⁰), an important property needed in design calculations has been estimated using molar refraction, R_M. The linear relationships derived between ΔG_f⁰ and R_M tested with the data on 8 series of hydrocarbons at 228 compounds yielded average deviations comparable to the methods cited in recent literature. The method can be used as an alternative to the existing ones, because of its simplicity combined with reasonable accuracy.     

Production of biodiesel from waste fryer grease using mixed methanol/ethanol system

Transesterification of waste fryer grease (WFG) containing 5–6 wt.% free fatty acid (FFA) was carried out with methanol, ethanol, and mixtures of methanol/ethanol maintaining the oil to alcohol molar ratio of 1:6, and initially with KOH as a catalyst. Mixtures of methanol and ethanol were used for transesterification in order to use the better solvent property of ethanol and rapid equilibrium using methanol. Formation of soap by reaction of FFA present in WFG with KOH instigated difficulty in the separation of glycerol from biodiesel ester. To untangle this problem, two-stage (acid and alkali catalyzed) method was used for biodiesel synthesis. More than 90% ester was obtained when two-stage method was used compared to ∼ 50% ester in single stage alkaline catalyst. In the case of mixed alcohol, a relatively smaller amount of ethyl esters was formed along with methyl esters. Acid value, viscosity, and cetane number of all the esters prepared from WFG were within the range of the ASTM standard. Esters obtained from WFG showed good performance as a lubricity additive.     

基于遗传算法的工作辊温度场参数优化模型

针对热连轧机工作辊热辊形计算中温度场模型的热交换等参数难以确定的问题 ,建立了基于遗传算法的参数优化模型 ,可以解决复杂条件下的热参数的求解问题。利用优化参数计算的轧辊温度场与实际测量结果一致。