Piezoelectric properties of PVDF-conjugated polymer nanofibers

This study presents the development and characterization of PVDF-conjugated polymer nanofiber-based systems. Five different conducting polymers (CPs) were synthesized successfully and used to create the nanofiber systems. The CPs used are polyaniline (PANI), polypyrrole (PPY), polyindole (PIN), polyanthranilic acid (PANA), and polycarbazole (PCZ). Nanofiber systems were produced utilizing the Forcespinning® technique. The nanofiber systems were developed by mechanical stretching. No electrical field or post-process poling was used in the nanofiber systems. The morphology, structure, electrochemical and piezoelectric performance was characterized. All of the nanofiber PVDF/CP systems displayed higher piezoelectric performance than the fine fiber PVDF systems. The PVDF/PPY nanofiber system displays the highest piezoelectric performance of 15.56 V. The piezoelectric performance of the PVDF/CP nanofiber systems favors potential for an attractive source of energy where highly flexible membranes could be used in power actuators, sensors and portable, and wireless devices to mention some.     

Statistical Piezotronic Effect in Nanocrystal Bulk by Anisotropic Geometry Control

Utilizing inner-crystal piezoelectric polarization charges to control carrier transport across a metal-semiconductor or semiconductor–semiconductor interface, piezotronic effect has great potential applications in smart micro/nano-electromechanical system (MEMS/NEMS), human-machine interfacing, and nanorobotics. However, current research on piezotronics has mainly focused on systems with only one or rather limited interfaces. Here, the statistical piezotronic effect is reported in ZnO bulk composited of nanoplatelets, of which the strain/stress-induced piezo-potential at the crystals’ interfaces can effectively gate the electrical transport of ZnO bulk. It is a statistical phenomenon of piezotronic modification of large numbers of interfaces, and the crystal orientation of inner ZnO nanoplatelets strongly influence the transport property of ZnO bulk. With optimum preferred orientation of ZnO nanoplatelets, the bulk exhibits an increased conductivity with decreasing stress at a high pressure range of 200–400 MPa, which has not been observed previously in bulk. A maximum sensitivity of 1.149 µS m⁻¹ MPa⁻¹ and a corresponding gauge factor of 467–589 have been achieved. As a statistical phenomenon of many piezotronic interfaces modulation, the proposed statistical piezotronic effect extends the connotation of piezotronics and promotes its practical applications in intelligent sensing.     

A Highly Sensitive,Reversible, and Bidirectional Humidity Actuator by Calcium Carbonate Ionic Oligomers Incorporated Poly(Vinylidene Fluoride)

Sensitivity and multi-directional motivation are major two factors for developing optimized humidity-response materials, which are promising for sensing, energy production, etc. Organic functional groups are commonly used as the water sensitive units through hydrogen bond interactions with water molecules in actuators. The multi-coordination ability of inorganic ions implies that the inorganic ionic compounds are potentially superior water sensitive units. However, the particle forms of inorganic ionic compounds produced by classical nucleation limit the number of exposed ions to interact with water. Recent progress on the inorganic ionic oligomers has broken through the limitation of classical nucleation, and realized the molecular-scaled incorporation of inorganic ionic compounds into an organic matrix. Here, the incorporation of hydrophilic calcium carbonate ionic oligomers into hydrophobic poly(vinylidene fluoride) (PVDF) is demonstrated. The ultra-small calcium carbonate oligomers within a PVDF film endow it with an ultra-sensitive, reversible, and bidirectional response. The motivation ability is superior to other bidirectional humidity-actuators at present, which realizes self-motivation on an ice surface, converting the chemical potential energy of the humidity gradient from ice to kinetic energy.     

Dielectric,ferroelectric, and piezoelectric properties of lead-free Ba0.95Ca0.05Ti1-xZrxO3 ceramics

Abstract

Ba_0.95Ca_0.05Ti_1-xZr_xO₃ (BCTZO) ceramics were prepared by a solid state reaction method. The samples were characterized by X-ray diffraction (XRD), Scanning electron microscopy (SEM) and X-ray absorption near edge structure (XANES). The ceramics exhibit a pure perovskite structure. The average grain size gradually decreases with increasing Zr concentration. XANES results indicate that the intensities of pre-edge peaks dropped with increasing Zr concentration. The BCTZO ceramic of x?=?0.05 has the optimum electrical properties with the maximum dielectric constant (ε'_m), remanent polarization (2P_r), coercive electric field (2E_c) and piezoelectric charge constant (d₃₃) of 7,244, 12.54 (μC/cm²), 5.29 (kV/cm) and 288 (pC/N), respectively.     

混凝土结构的压电声波检测分析

本文介绍了混凝土结构的压电体波和表面波检测的主要进展,对两种压电声波检测的优缺点进行了总结。体波检测设备一般埋入混凝土内部,需要选择合理的检测部位,检测结果较为精确;声表面波检测无需选择特定的部位,但是检测深度有限。在实际检测工作过程中,可以联合两种方法相互验证。     

Modelling,simulation and identification of an engine air path electromechanical actuator

This paper deals with the modelling and the identification of an electromechanical Diesel engine actuator. The studied Bosch GPA-S actuator is designed for swirl/tumble flaps to control the air amount entering into the cylinder. This study aims to design a complete simulator that reproduces, with sufficient accuracy, the actuator dynamics taking into account the effects of the friction phenomenon. Hence, an overview of the actuator structure and its operation principle is first given. Then, its mathematical model as well as the nonlinearity, related to its behaviour, is discussed. Next, three identification procedures, which allow estimating both the system parameters and the friction model coefficients, are introduced. Finally, simulation results, using MATLAB, and experimental results, using LabVIEW, are presented demonstrating the effectiveness of the proposed techniques.     

Experimental research on dynamic response of PZT-5H under impact load

In order to improve the stability of PZT-based sensors, the mechanical, dielectric, ferroelectric and piezoelectric properties of PZT-5H under impact load were studied experimentally by using the separated Hopkinson pressure bar (SHPB) with an electrical output measurement device. At the same time, the experimental study on the material properties of PZT-5H before and after the impact was carried out. The effect of impact cracks on the output voltage of PZT-5H was also analyzed. The results show that the dynamic piezoelectric constants of PZT-5H under low stress impact (10–50 MPa) are different from those under quasi-static state, and the empirical relationship between them and the peak stress is obtained through experiments. The dielectric properties of PZT-5H did not change under low stress impact, but micro-cracks occurred in the material and dielectric loss increased at high frequencies. Under short circuit, the residual polarization intensity of PZT-5H decreases sharply due to impact load. While the impact load causes the secondary polarization and the increase of the residual polarization intensity of PZT under open circuit. When the stress is over 45 MPa, the PZT-5H breaks. The formation of cracks causes abnormal discharge voltage and gap discharge.     

压电驱动器迟滞特性的Preisach模型研究

压电驱动器的迟滞特性是影响其位移输出精度的主要因素。该文采用改进的Preisach模型对压电驱动器的迟滞特性进行建模，并进行了相应的实验研究。实验结果表明该模型可以很好地预测压电驱动器在经过一定的控制电压序列以后的位移输出值．能够有效地降低迟滞特性对压电驱动器位移输出精度的影响。     

基于压电陶瓷动态信息的结构裂纹识别方法

利用压电陶瓷的动态特性和压电系统的动态信息,对铝梁的裂纹损伤进行了分析研究。随着梁裂纹尺寸的增加,压电陶瓷片的导钠幅值下降,且系统固有频率减小。利用导钠幅值的变化和系统的动态信息,可以对裂纹的位置和尺寸大小进行识别。实验证明该方法的有效性。     

Study of elastic wave propagation induced by piezoelectric actuators for crack identification

The current paper provides a theoretical study of elastic wave propagation in a cracked elastic medium induced by an embedded piezoelectric actuator. The formulation of the problem is based on a newly developed actuator model and the solution of coupled crack and actuator problems. The interaction between an actuator and a crack is studied to develop basic understanding of the effect of the crack upon the wave field generated. The resulting wave field is used to simulate 'sensor signals'. Scattered wave from the crack is then regenerated by solving a reverse elastodynamic problem and used in an imaging technique to identify the crack.