气力输送在烧结电除尘输灰系统中的应用

针对烧结厂烧结电除尘灰的工况特性，介绍了输送烧结电除尘灰的正压气力输灰系统的特点、组成，还对在调试和试运行过程中遇到的故障进行了分析并制订了解决措施。     

An Experimental Investigation into the Feed Rate Capacity of Rotary Valve and Blow Tank Feeders

Industry widely uses rotary valves and blow tanks for the pneumatic conveying of products, each having their pros and cons depending on the specific application. This article shows the differing results obtained when low-velocity conveying a product through a common pipeline using both a drop-through rotary valve and a bottom-discharge blow tank feeder. A number of issues arise in the rotary valve system, the main one being rotary valve air leakage. A blow tank system, on the other hand, does not leak, as it is an enclosed system. The experimental results show dramatic differences in product throughput. Further exploration leads to a novel modification being made to the rotary valve system in an attempt to increase its capacity. The result of this modification shows a slight increase in output tonnage, but still significantly less than that obtained from the blow tank.     

三(明)钢烧结厂电除尘灰的气力输送

三钢烧结厂130m^2烧结机电除尘输灰首次采用了气力输送系统。该系统由气源、输送、管路、灰库及控制五部分组成，本文介绍了系统的工作原理及运行调试情况。系统投产后，运行平稳，达到了设计要求。     

瓶组气化站的建筑、结构设计要点

瓶组气化站的建筑，结构设计关系到安全，满足使用要求和投资的大小，本文根据多年的实践和最新的有关设计规范的要求，阐述瓶组气化站建筑，结构设计的要点。     

三聚氰胺粉料后处理工艺技术改造

经过技改后的三聚氰胺粉料后处理工艺，克服了以往采用螺旋输送机冷却和正压输送工艺所带来的工作环境恶劣、产品因温度较高而不易包装、机械故障频繁等许多难以解决的问题。改用吸送式气力输送后处理工艺后，既能输送，又能冷却、提纯三聚氰胺，实现自动化包装，并彻底改善工作环境。     

顶部定常吸气对高层建筑模型气动力的影响

为减少高层建筑受到的风荷载,提高高层建筑抗风性能,提出一种顶部吸气的主动控制方法。在一高宽比为H/d=5的正方形截面柱体的高层建筑模型上,通过在其顶部前边缘开设狭缝进行吸气来实现流动控制。通过风洞试验研究了顶部吸气对气动力与顶部分离流的影响.利用流动可视化与流场测试结果揭示了顶部狭缝吸气的控制机理.实验对比了不同吸气系数Q(=U/U_∞,U为狭缝吸气速度)对气动力控制效果的影响,并对Q=0,1和3的三种工况下风压分布与顶部剪切流进行了详细对比.研究发现狭缝吸气改变了顶部分离流特性,并对模型所有高度上的气动力均有显著影响.Q=1时控制效果最佳,脉动阻力与脉动升力分别减小17.8%和45.5%.此时顶面分离流被削弱并伴随有再附现象且湍流强度较大,最有利于顶部剪切流与尾流间的动量交换,从而削弱柱体展向涡脱落与脉动气动力.     

高线精轧机平衡缸漏油分析及改进

分析了广州钢铁企业集团公司高线厂精轧机平衡油缸漏油的危害和原因，指出了这种油缸在设计上存在的缺陷，并提出了改进措施，改进后漏油问题得到了解决。     

手功能康复机器人的鲁棒控制研究

以手功能康复机器人为研究对象,对被控对象建立数学模型,推导鲁棒控制器,基于simMechanics建立仿真模型,实现手功能康复机器人的鲁棒控制系统。考虑到手功能康复机器人是帮助偏瘫患者进行康复训练并最大限度地诱发患肢的主动作用,控制器中加入偏瘫患者的主动作用函数。控制系统在MATLAB／Simulink的环境下仿真,结果表明所设计的鲁棒控制器能适应不同程度的偏瘫患者,具有较佳的动态特性和很强的鲁棒性能。     

Comparison of image reconstruction by using near‐field and far‐field data for an imperfect conductor

Image reconstruction by using near‐field and far‐field data for an imperfectly conducting cylinder is investigated. A conducting cylinder of unknown shape and conductivity scatters the incident wave in free space and the scattered near and far fields are measured. By using measured fields, the imaging problem is reformulated into an optimization problem and solved by the genetic algorithm. Numerical results show that the convergence speed and final reconstructed results by using near‐field data are better than those obtained by using far‐field data. This work provides both comparative and quantitative information. © 2001 John Wiley & Sons, Inc. Int J RF and Microwave CAE 11: 69–73, 2001.     

Computing Green's function of the initial-boundary value problem for the wave equation in a layered cylinder

A new analytical method for the approximate computation of the time-dependent Green's function for the initial-boundary value problem of the three-dimensional wave equation on multi-layered bounded cylinder is suggested in this paper. The method is based on the derivation of eigenvalues and eigenfunctions for an ordinary differential equation with piecewise constant coefficients, and an approximate computation of Green's function in the form of the Fourier series with a finite number of terms relative to the orthogonal set of the derived eigenfunctions. The computational experiment confirms the robustness of the method.